Ting Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ting Yang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Kaibin Li
Key Laboratory of Pressure System and Safety, Ministry of Education, East China University of Science and Technology, Shanghai 200237, China
3 shared publications - Weize Wang
Key Laboratory of Pressure System and Safety, Ministry of Education, East China University of Science and Technology, Shanghai, China
3 shared publications - Shilong Yang
Key Laboratory of Pressure System and Safety, Ministry of Education, East China University of Science and Technology, Shanghai 200237, China
2 shared publications - Yangguang Liu
Key Laboratory of Pressure System and Safety, Ministry of Education, East China University of Science and Technology, Shanghai 200237, China
2 shared publications - Pengpeng Liu
Key Laboratory of Pressure System and Safety, Ministry of Education, East China University of Science and Technology, Shanghai 200237, China
1 shared publication - Tianying Wang
Key Laboratory for Advanced Corrosion and Protection of Aviation Materials, AECC Beijing Institute of Aeronautical Materials, Beijing 100195, China
1 shared publication
Latest Publications
- Open Access
Experimental and Simulation Studies on Thermal Shock of Multilayer Thermal Barrier Coatings with an Intermediate Transition Layer at 1500 °C
Strain tolerance is a crucial factor affecting the thermal life of coatings, and a higher strain tolerance can effectively alleviate the thermal stresses on coatings during thermal shock. To improve the strain tolerance, the coating structure was optimized by introducing an intermediate transition layer in this study. The intermediate transition layer material was prepared using a 1:1 volume ratio mixture of 6–8 wt. % Yttria-stabilized zirconia (YSZ) and NiCrAlY powders in the experiments. The coating structure consisted of an Al2O3-GdAlO3 (AGAP) anti-erosion layer, a YSZ layer, an intermediate transition layer, and a bonding layer from top to bottom. After thermal shock experiments at 1500 °C, the coatings with the addition of the intermediate transition layer exhibited different failure modes, with the crack location shifting from between the YSZ and the bonding layer to within the intermediate transition layer, compared to the coatings without the intermediate transition layer. Finite element simulation analysis showed that the intermediate transition layer effectively increased the strain tolerance of the coating and significantly reduced the thermal stress. Furthermore, incorporating an embedded micron agglomerated particle-based (EMAP) thermal barrier coating structure into the intermediate transition layer effectively alleviated thermal stresses and enhanced the coating’s thermal insulation performance.
Open AccessExperimental and Simulation Studies on Thermal Shock of Multilayer Thermal Barrier Coatings with an Intermediate Transition Layer at 1500 °C
Strain tolerance is a crucial factor affecting the thermal life of coatings, and a higher strain tolerance can effectively alleviate the thermal stresses on coatings during thermal shock. To improve the strain tolerance, the coating structure was optimized by introducing an intermediate transition layer in this study. The intermediate transition layer material was prepared using a 1:1 volume ratio mixture of 6–8 wt. % Yttria-stabilized zirconia (YSZ) and NiCrAlY powders in the experiments. The coating structure consisted of an Al2O3-GdAlO3 (AGAP) anti-erosion layer, a YSZ layer, an intermediate transition layer, and a bonding layer from top to bottom. After thermal shock experiments at 1500 °C, the coatings with the addition of the intermediate transition layer exhibited different failure modes, with the crack location shifting from between the YSZ and the bonding layer to within the intermediate transition layer, compared to the coatings without the intermediate transition layer. Finite element simulation analysis showed that the intermediate transition layer effectively increased the strain tolerance of the coating and significantly reduced the thermal stress. Furthermore, incorporating an embedded micron agglomerated particle-based (EMAP) thermal barrier coating structure into the intermediate transition layer effectively alleviated thermal stresses and enhanced the coating’s thermal insulation performance.
- Open Access
Investigation on the Thermal–Mechanical Properties of YbRESiO5 (RE = Yb, Eu, Gd, Ho, Tm, Lu, Y, Sc): First-Principles Calculations and Thermal Performance Experiments
Environmental barrier coatings are critically needed in the future to safeguard SiC-based ceramic matrix composites (SiC CMCs) used in gas turbines. Element doping of rare earth monosilicates could further improve the properties of the coating. The crystal structure, elastic properties, and resistance to water vapor corrosion of Yb2SiO5 and YbRESiO5 (where RE = Sc, Y, Eu, Gd, Ho, Tm, Lu) were examined in this study using first-principles calculations. When RE is Yb, the material is Yb2SiO5. Based on the outcomes of the calculation, we prepared YbRESiO5 (RE = Sc, Yb, Eu) and studied the thermodynamic properties. The findings show that YbReSiO5’s resistance to water vapor corrosion is as follows: YbLuSiO5 < YbEuSiO5 < YbGdSiO5 < YbYSiO5 < Yb2SiO5 < YbTmSiO5 < YbHoSiO5 < YbScSiO5. YbScSiO5 has a lower unit cell volume, average Re-O bond length, and thermal expansion coefficient than Yb2SiO5, while YbEuSiO5 has the reverse pattern. Moreover, of the eight materials, YbScSiO5 has the greatest elastic modulus and lattice distortion. After doping with Eu, YbEuSiO5 exhibits a decrease in thermal conductivity by nearly thirty percent compared to Yb2SiO5, due to the formation of oxygen vacancies. The development of environmental barrier coating materials may benefit from these discoveries.
Open AccessInvestigation on the Thermal–Mechanical Properties of YbRESiO5 (RE = Yb, Eu, Gd, Ho, Tm, Lu, Y, Sc): First-Principles Calculations and Thermal Performance Experiments
Environmental barrier coatings are critically needed in the future to safeguard SiC-based ceramic matrix composites (SiC CMCs) used in gas turbines. Element doping of rare earth monosilicates could further improve the properties of the coating. The crystal structure, elastic properties, and resistance to water vapor corrosion of Yb2SiO5 and YbRESiO5 (where RE = Sc, Y, Eu, Gd, Ho, Tm, Lu) were examined in this study using first-principles calculations. When RE is Yb, the material is Yb2SiO5. Based on the outcomes of the calculation, we prepared YbRESiO5 (RE = Sc, Yb, Eu) and studied the thermodynamic properties. The findings show that YbReSiO5’s resistance to water vapor corrosion is as follows: YbLuSiO5 < YbEuSiO5 < YbGdSiO5 < YbYSiO5 < Yb2SiO5 < YbTmSiO5 < YbHoSiO5 < YbScSiO5. YbScSiO5 has a lower unit cell volume, average Re-O bond length, and thermal expansion coefficient than Yb2SiO5, while YbEuSiO5 has the reverse pattern. Moreover, of the eight materials, YbScSiO5 has the greatest elastic modulus and lattice distortion. After doping with Eu, YbEuSiO5 exhibits a decrease in thermal conductivity by nearly thirty percent compared to Yb2SiO5, due to the formation of oxygen vacancies. The development of environmental barrier coating materials may benefit from these discoveries.
- Open Access
Simulation of 1500 °C Thermal Shock for Novel Structural Thermal/Environmental Barrier Coatings System
In recent years, with the development of SiC composites in aero-engine hot-end components, environmental barrier coatings (EBCs) have received extensive attention. Moreover, in order to elevate the service temperature, it is a developing trend to apply thermal barrier coatings (TBCs) with low thermal conductivity on EBCs coating system to form thermal/environmental barrier coatings (T/EBCs). However, the combination of high coefficient of thermal expansion (CTE) of TBCs with low CTE of EBCs often leads to premature failure due to excessive thermal expansion mismatch stress. However, a novel structural thermal barrier coating with embedded micro-agglomerated particles (EMAP TBC) by using atmospheric plasma spraying (APS) process has brought hope to solve this problem due to its low elastic modulus. Therefore, in this study, an innovative EMAP Gd2Zr2O7 T/EBCs coating system (EMAP Gd2Zr2O7/Yb2Si2O7/Si) under 1500 °C flame thermal shock was simulated and systematically studied on the SiC substrate. The results showed that the EMAP Gd2Zr2O7 T/EBCs coating system has much lower thermal stress than the conventional Gd2Zr2O7/Yb2Si2O7/Si T/EBCs coating system. Furthermore, when the thickness of each layer of the EMAP Gd2Zr2O7 T/EBCs coating system varies, to meet the thermal insulation requirements of Yb2Si2O7 layer and reduce the thermal shock stress, the thickness of the EMAP Gd2Zr2O7 layer is recommend being about 100 μm. Meanwhile, the thicknesses of Yb2Si2O7 and Si layers can be set as large as needed. In addition, with the increase in Yb2SiO5 doping content in the Yb2Si2O7 intermediate layer, the EMAP Gd2Zr2O7 T/EBCs coating system suffers a greater risk of spalling failure due to the increase in thermal stress.
Open AccessSimulation of 1500 °C Thermal Shock for Novel Structural Thermal/Environmental Barrier Coatings System
In recent years, with the development of SiC composites in aero-engine hot-end components, environmental barrier coatings (EBCs) have received extensive attention. Moreover, in order to elevate the service temperature, it is a developing trend to apply thermal barrier coatings (TBCs) with low thermal conductivity on EBCs coating system to form thermal/environmental barrier coatings (T/EBCs). However, the combination of high coefficient of thermal expansion (CTE) of TBCs with low CTE of EBCs often leads to premature failure due to excessive thermal expansion mismatch stress. However, a novel structural thermal barrier coating with embedded micro-agglomerated particles (EMAP TBC) by using atmospheric plasma spraying (APS) process has brought hope to solve this problem due to its low elastic modulus. Therefore, in this study, an innovative EMAP Gd2Zr2O7 T/EBCs coating system (EMAP Gd2Zr2O7/Yb2Si2O7/Si) under 1500 °C flame thermal shock was simulated and systematically studied on the SiC substrate. The results showed that the EMAP Gd2Zr2O7 T/EBCs coating system has much lower thermal stress than the conventional Gd2Zr2O7/Yb2Si2O7/Si T/EBCs coating system. Furthermore, when the thickness of each layer of the EMAP Gd2Zr2O7 T/EBCs coating system varies, to meet the thermal insulation requirements of Yb2Si2O7 layer and reduce the thermal shock stress, the thickness of the EMAP Gd2Zr2O7 layer is recommend being about 100 μm. Meanwhile, the thicknesses of Yb2Si2O7 and Si layers can be set as large as needed. In addition, with the increase in Yb2SiO5 doping content in the Yb2Si2O7 intermediate layer, the EMAP Gd2Zr2O7 T/EBCs coating system suffers a greater risk of spalling failure due to the increase in thermal stress.