Rishabh Chaturvedi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rishabh Chaturvedi has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Majed A. Alotaibi
2 shared publicationsManzoore Elahi M. Soudagar
2 shared publications- V. Mohanavel
Centre for Sustainable Materials Research, Department of Mechanical Engineering, Academy of Maritime Education and Training (AMET) Deemed to be University, Kanathur, Chennai, India
2 shared publications Vinayagam Mohanavel
2 shared publicationsA. Mohana Krishnan
1 shared publicationAbdulaziz Ibrahim Almohana
1 shared publication
Latest Publications
- 18 November 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (23) , 14389-14402
Enhancement of solar cooking performance by utilizing hybrid SiC/Ag featured nano-PCM heat exchanger integrated with parabolic trough collector
- 18 November 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (23) , 14389-14402
Enhancement of solar cooking performance by utilizing hybrid SiC/Ag featured nano-PCM heat exchanger integrated with parabolic trough collector
- Open Access
- 1 November 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (11)
Experimental and numerical analysis on the cutting force, cutting temperature, and tool wear of alloy steel (4340) during turning process
This paper focuses primarily on the wear behavior observed in AISI4340 steel when machining with a multi-layered coated carbide tool. Numerical and experimental examination is processed out to predict the wear performance of AISI 4340 steel along with its cutting force and temperature. In this process, four layers of different coated material are bonded together to form a multi-layered coated carbide tool. The coated thickness is assessed with the assistance of a Scanning Electron Microscope (SEM). Experimental analysis takes place with a heavy duty lathe machine equipped with an infrared thermometer and force dynamometer. Simulation is performed using DEFORM-2D software to simulate cutting forces and interface temperature, and the output results obtained have been compared with the experimental work. With the help of the SEM image, maximum crater wear depth is evaluated and analyzed. Feed plays a crucial role in increasing the chip interface temperature and cutting force. For varied feed rates, the cutting tool edge radius, depth of cut, and cutting speed are taken as the input parameters. The proposed 2D finite element model provides effective parameter values for reducing wear. Results measured indicate that the output parameter values of interface temperature and cutting force obtained from simulation and experimental investigation match each other with high accuracy. Simulation results for temperature distribution around the tool tip show that a maximum temperature of 654 °C is formed at the feed rate of 0.4 mm/rev, leading to high heat flux. For the feed rate of 0.3 and 0.2 mm/rev, there is not much deviation in heat flux around the tool tip. The maximum temperature around the tool tip is near 527 °C for both 0.3 and 0.2 mm/rev. Simulation results show that the lowest tool wear of 0.001 23 mm was obtained for a feed rate of 0.2 mm/rev, followed by 0.004 25 (0.1 mm/rev), 0.005 09 mm (0.4 mm/rev), and 0.007 14 mm/rev.
- 1 November 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (11)
Open AccessExperimental and numerical analysis on the cutting force, cutting temperature, and tool wear of alloy steel (4340) during turning process
This paper focuses primarily on the wear behavior observed in AISI4340 steel when machining with a multi-layered coated carbide tool. Numerical and experimental examination is processed out to predict the wear performance of AISI 4340 steel along with its cutting force and temperature. In this process, four layers of different coated material are bonded together to form a multi-layered coated carbide tool. The coated thickness is assessed with the assistance of a Scanning Electron Microscope (SEM). Experimental analysis takes place with a heavy duty lathe machine equipped with an infrared thermometer and force dynamometer. Simulation is performed using DEFORM-2D software to simulate cutting forces and interface temperature, and the output results obtained have been compared with the experimental work. With the help of the SEM image, maximum crater wear depth is evaluated and analyzed. Feed plays a crucial role in increasing the chip interface temperature and cutting force. For varied feed rates, the cutting tool edge radius, depth of cut, and cutting speed are taken as the input parameters. The proposed 2D finite element model provides effective parameter values for reducing wear. Results measured indicate that the output parameter values of interface temperature and cutting force obtained from simulation and experimental investigation match each other with high accuracy. Simulation results for temperature distribution around the tool tip show that a maximum temperature of 654 °C is formed at the feed rate of 0.4 mm/rev, leading to high heat flux. For the feed rate of 0.3 and 0.2 mm/rev, there is not much deviation in heat flux around the tool tip. The maximum temperature around the tool tip is near 527 °C for both 0.3 and 0.2 mm/rev. Simulation results show that the lowest tool wear of 0.001 23 mm was obtained for a feed rate of 0.2 mm/rev, followed by 0.004 25 (0.1 mm/rev), 0.005 09 mm (0.4 mm/rev), and 0.007 14 mm/rev.
- Retracted
- 10 January 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 51, 1142-1155
RETRACTED: Thermodynamic performance optimization and environmental analysis of a solid oxide fuel cell powered with biomass energy and excess hydrogen injection
- 10 January 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 51, 1142-1155
RetractedRETRACTED: Thermodynamic performance optimization and environmental analysis of a solid oxide fuel cell powered with biomass energy and excess hydrogen injection