Hongyu Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hongyu Lu has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Patrick P. Mercier
Department of Electrical and Computer Engineering, University of California, San Diego, La Jolla, CA, USA
7 shared publications - Nader Sherif Kassem Fathy
Department of Electrical and Computer Engineering, University of California at San Diego, La Jolla, CA, USA
2 shared publications - Abraham Akinin
Lawrence Livermore National Laboratory, Livermore, CA, USA
1 shared publication - Ahmed Gharib Gadel-Karim
Department of Electrical and Computer Engineering, University of California San Diego, La Jolla, CA, USA
1 shared publication Ahmed Gharib Gadelkarim
Department of Electrical and Computer Engineering, University of California at San Diego, La Jolla, CA, USA
1 shared publication- Akshay Paul
Shu Chien-Gene Lay Department of Bioengineering, University of California San Diego, La Jolla, CA, USA
1 shared publication
Latest Publications
- 14 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 9, 57-60
A Ring-Oscillator-Based Digital Harmonic-Mixing Fractional- N PLL
This letter presents a low-jitter digital harmonic-mixing fractional- $N$ phase-locked loop (PLL) using a ring oscillator. To extend the loop bandwidth, a mixer with unity gain in the phase domain is adopted, which helps suppress phase noise of the phase detector and delta-sigma modulator. Furthermore, to reduce mixing harmonics that would otherwise dominate the in-band jitter, the sinusoidal reference is buffered by a linear source follower, in contrast to the inverters used in other LC-oscillator-based harmonic-mixing PLLs. Implemented in 65 nm CMOS, the proposed PLL achieves 603.8 fs root-mean-square jitter with a 100 MHz integration bandwidth. It occupies $0.12~\text {mm}^{2}$ of silicon area and consumes 12.72 mW of power.
- 14 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 9, 57-60
A Ring-Oscillator-Based Digital Harmonic-Mixing Fractional- N PLL
This letter presents a low-jitter digital harmonic-mixing fractional- $N$ phase-locked loop (PLL) using a ring oscillator. To extend the loop bandwidth, a mixer with unity gain in the phase domain is adopted, which helps suppress phase noise of the phase detector and delta-sigma modulator. Furthermore, to reduce mixing harmonics that would otherwise dominate the in-band jitter, the sinusoidal reference is buffered by a linear source follower, in contrast to the inverters used in other LC-oscillator-based harmonic-mixing PLLs. Implemented in 65 nm CMOS, the proposed PLL achieves 603.8 fs root-mean-square jitter with a 100 MHz integration bandwidth. It occupies $0.12~\text {mm}^{2}$ of silicon area and consumes 12.72 mW of power.
- 27 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (12) , 6021-6033
Linear Periodically Time-Variant Digital PLL Phase Noise Modeling Using Conversion Matrices and Uncorrelated Upsampling
This paper introduces a conversion matrix method for linear periodically time-variant (LPTV) digital phase-locked loop (DPLL) phase noise modeling that offers precise and computationally efficient results to enable rapid design iteration and optimization. Unlike many previous studies, which either assume linear time-invariance (LTI) and therefore overlook phase noise aliasing effects, or solve LPTV systems with noise folding and multiple sampling rate conversions that heightens modeling and computational complexity, the proposed conversion matrix method allows the designer to represent LPTV systems using intuitive LTI-like transfer functions with excellent accuracy. Additionally, the uncorrelated upsampling method addresses the cross-correlated spectrum of cyclostationary noise sources by a simple matrix multiplication. This eliminates the need to consider the beat frequency of the upsampled noise source and the system with different sampling rates, thus improving computational efficiency. The proposed algorithm is applied to modeling a integer- $N$ DPLL with time-varying proportional loop gain, and the modeling accuracy is validated with Simulink transient simulations.
- 27 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (12) , 6021-6033
Linear Periodically Time-Variant Digital PLL Phase Noise Modeling Using Conversion Matrices and Uncorrelated Upsampling
This paper introduces a conversion matrix method for linear periodically time-variant (LPTV) digital phase-locked loop (DPLL) phase noise modeling that offers precise and computationally efficient results to enable rapid design iteration and optimization. Unlike many previous studies, which either assume linear time-invariance (LTI) and therefore overlook phase noise aliasing effects, or solve LPTV systems with noise folding and multiple sampling rate conversions that heightens modeling and computational complexity, the proposed conversion matrix method allows the designer to represent LPTV systems using intuitive LTI-like transfer functions with excellent accuracy. Additionally, the uncorrelated upsampling method addresses the cross-correlated spectrum of cyclostationary noise sources by a simple matrix multiplication. This eliminates the need to consider the beat frequency of the upsampled noise source and the system with different sampling rates, thus improving computational efficiency. The proposed algorithm is applied to modeling a integer- $N$ DPLL with time-varying proportional loop gain, and the modeling accuracy is validated with Simulink transient simulations.
- Open Access
- 19 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 4, 57-68
A 0.69-mW Subsampling NB-IoT Receiver Employing a Linearized Q-Boosted LNA
This paper presents a receiver for NB-IoT that eliminates the need for an RF local oscillator (LO) via a sub-sampling architecture. A pseudo-balun Q-boosted LNA provides sharp anti-aliasing filtering with a noise figure (NF) of 5.6 dB. A direct-coupling derivative superposition technique where low-Vt and thick-gate transistors with opposite non-linear characteristics are combined to improve the measured IIP3 by 7 dB to -18 dBm with little NF overhead. Fabricated in 65 nm CMOS, the entire receiver, including the LNA, a S/H circuit and a 10-bit SAR ADC, consumes only 0.69 mW while meeting NB-IoT specifications.
- 19 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 4, 57-68
Open AccessA 0.69-mW Subsampling NB-IoT Receiver Employing a Linearized Q-Boosted LNA
This paper presents a receiver for NB-IoT that eliminates the need for an RF local oscillator (LO) via a sub-sampling architecture. A pseudo-balun Q-boosted LNA provides sharp anti-aliasing filtering with a noise figure (NF) of 5.6 dB. A direct-coupling derivative superposition technique where low-Vt and thick-gate transistors with opposite non-linear characteristics are combined to improve the measured IIP3 by 7 dB to -18 dBm with little NF overhead. Fabricated in 65 nm CMOS, the entire receiver, including the LNA, a S/H circuit and a 10-bit SAR ADC, consumes only 0.69 mW while meeting NB-IoT specifications.
- 26 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 18 (2) , 263-273
A Low-Noise Low-Power 0.001Hz–1kHz Neural Recording System-on-Chip With Sample-Level Duty-Cycling
Advances in brain-machine interfaces and wearable biomedical sensors for healthcare and human-computer interactions call for precision electrophysiology to resolve a variety of biopotential signals across the body that cover a wide range of frequencies, from the mHz-range electrogastrogram (EGG) to the kHz-range electroneurogram (ENG). Existing integrated wearable solutions for minimally invasive biopotential recordings are limited in detection range and accuracy due to trade-offs in bandwidth, noise, input impedance, and power consumption. This article presents a 16-channel wide-band ultra-low-noise neural recording system-on-chip (SoC) fabricated in 65nm CMOS for chronic use in mobile healthcare settings that spans a bandwidth of 0.001 Hz to 1 kHz through a featured sample-level duty-cycling (SLDC) mode. Each recording channel is implemented by a delta-sigma analog-to-digital converter (ADC) achieving 1.0 μ V rms input-referred noise over 1Hz–1kHz bandwidth with a Noise Efficiency Factor (NEF) of 2.93 in continuous operation mode. In SLDC mode, the power supply is duty-cycled while maintaining consistently low input-referred noise levels at ultra-low frequencies (1.1 μ V rms over 0.001Hz–1Hz) and 435 MΩ input impedance. The functionalities of the proposed SoC are validated with two human electrophysiology applications: recording low-amplitude electroencephalogram (EEG) through electrodes fixated on the forehead to monitor brain waves, and ultra-slow-wave electrogastrogram (EGG) through electrodes fixated on the abdomen to monitor digestion.
- 26 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 18 (2) , 263-273
A Low-Noise Low-Power 0.001Hz–1kHz Neural Recording System-on-Chip With Sample-Level Duty-Cycling
Advances in brain-machine interfaces and wearable biomedical sensors for healthcare and human-computer interactions call for precision electrophysiology to resolve a variety of biopotential signals across the body that cover a wide range of frequencies, from the mHz-range electrogastrogram (EGG) to the kHz-range electroneurogram (ENG). Existing integrated wearable solutions for minimally invasive biopotential recordings are limited in detection range and accuracy due to trade-offs in bandwidth, noise, input impedance, and power consumption. This article presents a 16-channel wide-band ultra-low-noise neural recording system-on-chip (SoC) fabricated in 65nm CMOS for chronic use in mobile healthcare settings that spans a bandwidth of 0.001 Hz to 1 kHz through a featured sample-level duty-cycling (SLDC) mode. Each recording channel is implemented by a delta-sigma analog-to-digital converter (ADC) achieving 1.0 μ V rms input-referred noise over 1Hz–1kHz bandwidth with a Noise Efficiency Factor (NEF) of 2.93 in continuous operation mode. In SLDC mode, the power supply is duty-cycled while maintaining consistently low input-referred noise levels at ultra-low frequencies (1.1 μ V rms over 0.001Hz–1Hz) and 435 MΩ input impedance. The functionalities of the proposed SoC are validated with two human electrophysiology applications: recording low-amplitude electroencephalogram (EEG) through electrodes fixated on the forehead to monitor brain waves, and ultra-slow-wave electrogastrogram (EGG) through electrodes fixated on the abdomen to monitor digestion.
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 46-49
A Mixer-First Receiver With On-Demand Passive Harmonic Rejection
This letter presents a mixer-first RF receiver that: 1) nominally operates in a low-NF $N$ -path filter mode; 2) features an on-chip harmonic blocker detection circuit running in the background; 3) switches to a harmonic rejection mode upon detection of harmonic content; and 4) passively rejects harmonic blockers through a current-mode circuit that uses resistor sizing to set the amplitude of each path, but with capacitive termination to minimize conversion loss to 1.9 dB while providing a sharp, down-converted filter response. Implemented in 65nm CMOS, the receiver achieves 36/40-dB HR3/5,+21 dBm IIP3, +1 dBm blocker 1-dB compression point (B1dB) and 4/8-dB NF while consuming 10–23 mW.
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 46-49
A Mixer-First Receiver With On-Demand Passive Harmonic Rejection
This letter presents a mixer-first RF receiver that: 1) nominally operates in a low-NF $N$ -path filter mode; 2) features an on-chip harmonic blocker detection circuit running in the background; 3) switches to a harmonic rejection mode upon detection of harmonic content; and 4) passively rejects harmonic blockers through a current-mode circuit that uses resistor sizing to set the amplitude of each path, but with capacitive termination to minimize conversion loss to 1.9 dB while providing a sharp, down-converted filter response. Implemented in 65nm CMOS, the receiver achieves 36/40-dB HR3/5,+21 dBm IIP3, +1 dBm blocker 1-dB compression point (B1dB) and 4/8-dB NF while consuming 10–23 mW.
- 11 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 225-228
LTE-Powered BLE-to-WiFi Backscattering Chip Toward Single-Device Interrogation RFID-Like Systems
This paper presents a backscattering chip that is powered via LTE signals, and reflects an incident reverse-whitened Bluetooth Low Energy (BLE) tone-like advertisement packet into a re-radiated single-side-band (SSB) 802.11b WiFi packet at a configurable WiFi channel location, all towards enabling an RFID-like single-device interrogation system. The chip includes an RF energy harvester, a WiFi wake-up receiver, an intermediate frequency (IF) ring oscillator whose frequency is calibrated with a successive-approximation-register (SAR) frequency-lock-loop (FLL), and a QPSK SSB backscatter modulator. Implemented in 65-nm CMOS, the chip consumes 4.5 μW power in wake-up mode and 11 to 45 μW power in backscatter mode, with on-chip ring oscillator frequencies ranging from 33 to 253 MHz in order to support 8 different BLE-to-WiFi backscatter schemes. Wireless measurement showed that the chip can be charged to 1V before backscattering within 1 sec on a 1μF off-chip storage capacitor up to a 50cm distance.
- 11 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 225-228
LTE-Powered BLE-to-WiFi Backscattering Chip Toward Single-Device Interrogation RFID-Like Systems
This paper presents a backscattering chip that is powered via LTE signals, and reflects an incident reverse-whitened Bluetooth Low Energy (BLE) tone-like advertisement packet into a re-radiated single-side-band (SSB) 802.11b WiFi packet at a configurable WiFi channel location, all towards enabling an RFID-like single-device interrogation system. The chip includes an RF energy harvester, a WiFi wake-up receiver, an intermediate frequency (IF) ring oscillator whose frequency is calibrated with a successive-approximation-register (SAR) frequency-lock-loop (FLL), and a QPSK SSB backscatter modulator. Implemented in 65-nm CMOS, the chip consumes 4.5 μW power in wake-up mode and 11 to 45 μW power in backscatter mode, with on-chip ring oscillator frequencies ranging from 33 to 253 MHz in order to support 8 different BLE-to-WiFi backscatter schemes. Wireless measurement showed that the chip can be charged to 1V before backscattering within 1 sec on a 1μF off-chip storage capacitor up to a 50cm distance.
- 2 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 5-8
A 0.11-mW 2.4-GHz Receiver Employing a Q-Boosted Impedance Transformer and Regenerative Amplifier Achieving −101-dBm Sensitivity and −28-dB SIR
This letter presents a 2.4 GHz OOK receiver that employs a Q-boosted impedance transformer and a regenerative amplifiers (RA) to provide high gain and sharp filtering prior to demodulation. A differential envelope detector (ED) is also used to increase the conversion gain further to help nullify the noise contribution of the subsequent baseband stages. Fabricated in 65 nm, the receiver achieves a sensitivity of -101 dBm at a data rate of 5 kbps, all while consuming 112 µW. The sharp RF filtering helps enable a signal-to-interference ratio (SIR) of -28 dB.
- 2 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 6, 5-8
A 0.11-mW 2.4-GHz Receiver Employing a Q-Boosted Impedance Transformer and Regenerative Amplifier Achieving −101-dBm Sensitivity and −28-dB SIR
This letter presents a 2.4 GHz OOK receiver that employs a Q-boosted impedance transformer and a regenerative amplifiers (RA) to provide high gain and sharp filtering prior to demodulation. A differential envelope detector (ED) is also used to increase the conversion gain further to help nullify the noise contribution of the subsequent baseband stages. Fabricated in 65 nm, the receiver achieves a sensitivity of -101 dBm at a data rate of 5 kbps, all while consuming 112 µW. The sharp RF filtering helps enable a signal-to-interference ratio (SIR) of -28 dB.