Young-Seong Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Young-Seong Kim has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Hee Chang Jeon
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
8 shared publications - Joong Yeon Lim
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
8 shared publications - Seonghwan Kim
University of Calgary
4 shared publications Minwook Park
Department of Mechanical, Robotics, and Energy Engineering, Dongguk University-Seoul, Seoul, Republic of Korea
3 shared publicationsSeonghwan Kim
Department of Mechanical and Manufacturing Engineering, Schulich School of Engineering, University of Calgary, Calgary, Canada
3 shared publications- Woohyuk Jang
Department of Mechanical, Robotics and Energy Engineering, Dongguk University, Jung-gu, Seoul 04620, Republic of Korea
3 shared publications
Latest Publications
- Open Access
Fabrication of Electrospun PAN–CNT–CNC Composite Nanofiber Films for Hydrovoltaic Energy Harvesting
Water-induced electrical responses were investigated using porous electrospun PAN-based composite membranes containing CNTs and CNCs. Following the injection of 20 μL of a 2 wt% NaCl solution, transient open-circuit voltage responses were observed from the PAN, PAN–CNT, and PAN–CNT–CNC devices, with maximum values of approximately 47, 42, and 68 mV, respectively, in the tested devices. Three successive injection–drying cycles demonstrated repeated transient responses within individual devices but did not establish device-to-device reproducibility or long-term stability. Raman and FTIR analyses supported the incorporation of CNTs and the modification of the water-interacting environment following CNC addition, respectively. The voltage waveform depended on the liquid type, NaCl concentration, and wetting–drying history, including a transient reverse-voltage response during drying. These results provide a proof-of-concept observation of wetting–drying-dependent electrical behavior in electrospun PAN-based porous membranes. Load-dependent power, long-term durability, and device-to-device reproducibility remain to be established.
Open AccessFabrication of Electrospun PAN–CNT–CNC Composite Nanofiber Films for Hydrovoltaic Energy Harvesting
Water-induced electrical responses were investigated using porous electrospun PAN-based composite membranes containing CNTs and CNCs. Following the injection of 20 μL of a 2 wt% NaCl solution, transient open-circuit voltage responses were observed from the PAN, PAN–CNT, and PAN–CNT–CNC devices, with maximum values of approximately 47, 42, and 68 mV, respectively, in the tested devices. Three successive injection–drying cycles demonstrated repeated transient responses within individual devices but did not establish device-to-device reproducibility or long-term stability. Raman and FTIR analyses supported the incorporation of CNTs and the modification of the water-interacting environment following CNC addition, respectively. The voltage waveform depended on the liquid type, NaCl concentration, and wetting–drying history, including a transient reverse-voltage response during drying. These results provide a proof-of-concept observation of wetting–drying-dependent electrical behavior in electrospun PAN-based porous membranes. Load-dependent power, long-term durability, and device-to-device reproducibility remain to be established.
- Open Access
- 30 August 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (17) , 7770
Nanoscale Electromechanical and Conductive Properties of a Layered Two-Dimensional Hybrid Perovskite
Two-dimensional (2D) organic–inorganic hybrid perovskites exhibit coupled ionic, electronic, and electromechanical responses that can strongly influence local charge transport. Here, solution-processed mixed-halide butylammonium lead perovskite crystals were mechanically exfoliated and investigated using X-ray diffraction, atomic force microscopy, piezoresponse force microscopy (PFM), and conductive atomic force microscopy (c-AFM). PFM measurements under −5, 0, and +5 V revealed clear bias-dependent changes in amplitude and phase, indicating an electric field-sensitive local electromechanical response. Local c-AFM measurements showed nonlinear bipolar hysteresis, with a pronounced increase in current near +7–8 V and a decrease near −7 to −6 V during the subsequent negative sweep. Because the crystals are mixed ionic–electronic conductors and the nanoscale tip–sample junction introduces substantial injection and contact barriers, the observed behavior is interpreted as resistive switching-like conductivity modulation, rather than definitive ferroelectric switching. The results are consistent with the combined contributions of charge injection, trap filling, possible ionic redistribution, and piezoelectricity-associated modulation of the local transport barrier. These findings provide nanoscale insight into electric field-dependent electromechanical and out-of-plane conductive behaviors in layered 2D hybrid perovskites.
- 30 August 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (17) , 7770
Open AccessNanoscale Electromechanical and Conductive Properties of a Layered Two-Dimensional Hybrid Perovskite
Two-dimensional (2D) organic–inorganic hybrid perovskites exhibit coupled ionic, electronic, and electromechanical responses that can strongly influence local charge transport. Here, solution-processed mixed-halide butylammonium lead perovskite crystals were mechanically exfoliated and investigated using X-ray diffraction, atomic force microscopy, piezoresponse force microscopy (PFM), and conductive atomic force microscopy (c-AFM). PFM measurements under −5, 0, and +5 V revealed clear bias-dependent changes in amplitude and phase, indicating an electric field-sensitive local electromechanical response. Local c-AFM measurements showed nonlinear bipolar hysteresis, with a pronounced increase in current near +7–8 V and a decrease near −7 to −6 V during the subsequent negative sweep. Because the crystals are mixed ionic–electronic conductors and the nanoscale tip–sample junction introduces substantial injection and contact barriers, the observed behavior is interpreted as resistive switching-like conductivity modulation, rather than definitive ferroelectric switching. The results are consistent with the combined contributions of charge injection, trap filling, possible ionic redistribution, and piezoelectricity-associated modulation of the local transport barrier. These findings provide nanoscale insight into electric field-dependent electromechanical and out-of-plane conductive behaviors in layered 2D hybrid perovskites.
- 13 August 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (31) , 16539-16548
DMSO-incorporated low-dimensional butylammonium lead iodide hybrid crystal
A DMSO-incorporated low-dimensional BA–Pb–I hybrid crystal with a 1D Pb–I ribbon motif is formed by room-temperature mixed-solvent crystallization and exhibits excitonic emission with reduced phonon-induced linewidth broadening.
- 13 August 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (31) , 16539-16548
DMSO-incorporated low-dimensional butylammonium lead iodide hybrid crystal
A DMSO-incorporated low-dimensional BA–Pb–I hybrid crystal with a 1D Pb–I ribbon motif is formed by room-temperature mixed-solvent crystallization and exhibits excitonic emission with reduced phonon-induced linewidth broadening.
- Open Access
- 8 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1) , 27525
Temperature-dependent thermoelectric behavior of metal-doped nanoporous carbon with tailored pore structures for multilevel temperature sensing
Metal-doped nanoporous carbon (MDNC) derived from core–shell metal–organic frameworks (MOFs) exhibits temperature-dependent thermoelectric behavior that is highly sensitive to nanoporous structure and surface interactions. In this study, a pellet-based approach is employed to enable systematic investigation of the Seebeck coefficient and electrical conductivity of MDNC as a function of temperature. Differential scanning calorimetry (DSC) reveals a pronounced desorption process in the temperature range of 80–100 ℃, which is closely correlated with significant changes in electrical transport properties. To further elucidate this behavior, MDNC samples with different particle sizes (~ 200 nm and ~ 800 nm) are examined, demonstrating distinct temperature-dependent variations in both Seebeck coefficient and electrical conductivity. These results indicate that temperature-induced desorption plays a critical role in modulating carrier transport through changes in interfacial barriers, scattering mechanisms, and conductive pathway connectivity. The particle-size-dependent nanoporous structure further influences this behavior by altering adsorption/desorption characteristics. Overall, this study provides insight into the coupling between nanoporous structure and temperature-dependent transport behavior in MDNC, offering a framework for understanding and tuning thermoelectric responses in nanoporous carbon systems.
- 8 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1) , 27525
Open AccessTemperature-dependent thermoelectric behavior of metal-doped nanoporous carbon with tailored pore structures for multilevel temperature sensing
Metal-doped nanoporous carbon (MDNC) derived from core–shell metal–organic frameworks (MOFs) exhibits temperature-dependent thermoelectric behavior that is highly sensitive to nanoporous structure and surface interactions. In this study, a pellet-based approach is employed to enable systematic investigation of the Seebeck coefficient and electrical conductivity of MDNC as a function of temperature. Differential scanning calorimetry (DSC) reveals a pronounced desorption process in the temperature range of 80–100 ℃, which is closely correlated with significant changes in electrical transport properties. To further elucidate this behavior, MDNC samples with different particle sizes (~ 200 nm and ~ 800 nm) are examined, demonstrating distinct temperature-dependent variations in both Seebeck coefficient and electrical conductivity. These results indicate that temperature-induced desorption plays a critical role in modulating carrier transport through changes in interfacial barriers, scattering mechanisms, and conductive pathway connectivity. The particle-size-dependent nanoporous structure further influences this behavior by altering adsorption/desorption characteristics. Overall, this study provides insight into the coupling between nanoporous structure and temperature-dependent transport behavior in MDNC, offering a framework for understanding and tuning thermoelectric responses in nanoporous carbon systems.
- Open Access
- 30 April 2026
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 39 (2) , 111-114
Finite-Element Analysis of Dental-Implant Screws Based on Thread Geometry Conditions
- 30 April 2026
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 39 (2) , 111-114
Open AccessFinite-Element Analysis of Dental-Implant Screws Based on Thread Geometry Conditions
- 14 April 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1026
High temperature coefficient of resistance material with metal-doped nanoporous carbon for low-temperature sensor
- 14 April 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1026
High temperature coefficient of resistance material with metal-doped nanoporous carbon for low-temperature sensor
- 11 April 2025
- Published by Wiley in Advanced Optical Materials
- Vol. 13 (20)
Alternating Current Photodetectors in Hybrid Perovskites with Modulated Oscillation Frequency
Growing interest has emerged in the alternating current (AC) photovoltaic effect, distinct from the traditional direct‐current (DC)‐based photovoltaic effect. This effect arises from the relative movement and reorganization of quasi‐Fermi levels at material interfaces when light is toggled on or off. In this study, a halide‐perovskite‐based photodetector is successfully fabricated, demonstrating the AC photovoltaic effect through oscillation frequency modulation and light‐chopping‐induced optical frequency tuning. For the first time, in sample impedance and the AC photovoltaic effect in this system are observed changes. Under specific conditions—light‐chopping frequency of 4 Hz, 0 V bias, 500 mV oscillation voltage, and resonance frequency of 16.8 MHz—a distinctive AC photoresponse at 405 nm wavelength is confirmed. This phenomenon is attributed to the influence of oscillation frequency on charge carriers, impacting electron dynamics such as capture and emission within the energy bands. The developed photodetector exhibits efficient responses to optical frequency and light intensity changes, aligning with the characteristics of conventional AC photodetectors. This work establishes a novel pathway for high‐performance AC photodetectors with superior sensitivity and tunability, surpassing traditional DC devices, and sets the foundation for further advancements in optoelectronic applications.
- 11 April 2025
- Published by Wiley in Advanced Optical Materials
- Vol. 13 (20)
Alternating Current Photodetectors in Hybrid Perovskites with Modulated Oscillation Frequency
Growing interest has emerged in the alternating current (AC) photovoltaic effect, distinct from the traditional direct‐current (DC)‐based photovoltaic effect. This effect arises from the relative movement and reorganization of quasi‐Fermi levels at material interfaces when light is toggled on or off. In this study, a halide‐perovskite‐based photodetector is successfully fabricated, demonstrating the AC photovoltaic effect through oscillation frequency modulation and light‐chopping‐induced optical frequency tuning. For the first time, in sample impedance and the AC photovoltaic effect in this system are observed changes. Under specific conditions—light‐chopping frequency of 4 Hz, 0 V bias, 500 mV oscillation voltage, and resonance frequency of 16.8 MHz—a distinctive AC photoresponse at 405 nm wavelength is confirmed. This phenomenon is attributed to the influence of oscillation frequency on charge carriers, impacting electron dynamics such as capture and emission within the energy bands. The developed photodetector exhibits efficient responses to optical frequency and light intensity changes, aligning with the characteristics of conventional AC photodetectors. This work establishes a novel pathway for high‐performance AC photodetectors with superior sensitivity and tunability, surpassing traditional DC devices, and sets the foundation for further advancements in optoelectronic applications.
- Open Access
- 18 February 2025
- Published by Elsevier in Results in Physics
- Vol. 70
Modulated magnetic and piezoresponse phase by applied electric field in 2D layered materials at room temperature
- 18 February 2025
- Published by Elsevier in Results in Physics
- Vol. 70
Open AccessModulated magnetic and piezoresponse phase by applied electric field in 2D layered materials at room temperature
- Open Access
Enhancing Piezoelectricity of Polyacrylonitrile–Cellulose Composite Nanofibers via Zigzag Conformation
A novel piezoelectric material, polyacrylonitrile (PAN) nanofibers, exhibits significant piezoelectric effects when a high content of planar zigzag structures is present. To enhance the contribution of planar zigzag structures to energy conversion while preserving the structure of PAN nanofibers, a novel approach was developed to increase planar zigzag content by incorporating cellulose nanocrystals (CNCs) rather than modifying conventional synthesis conditions. In this study, CNCs were introduced during the electrospinning process of PAN formation, and the increased planar zigzag content was confirmed through X-ray diffraction (XRD), electrical characterization, and Fourier transform infrared spectroscopy (FTIR) analyses. This study, for the first time, demonstrates that CNC addition to PAN enhances the mechanical properties and piezoelectric performance by promoting the formation of zigzag structures, which play a crucial role in the piezoelectric effect. The PAN–CNC composite holds great potential for applications in new piezoelectric devices. With CNC incorporation, the voltage increased by 68.9%, and the current increased by 80% compared to regular PAN. The generated energy is suitable for human applications and can also power commercial devices, making these findings pivotal for the advancement of piezoelectric materials and devices.
Open AccessEnhancing Piezoelectricity of Polyacrylonitrile–Cellulose Composite Nanofibers via Zigzag Conformation
A novel piezoelectric material, polyacrylonitrile (PAN) nanofibers, exhibits significant piezoelectric effects when a high content of planar zigzag structures is present. To enhance the contribution of planar zigzag structures to energy conversion while preserving the structure of PAN nanofibers, a novel approach was developed to increase planar zigzag content by incorporating cellulose nanocrystals (CNCs) rather than modifying conventional synthesis conditions. In this study, CNCs were introduced during the electrospinning process of PAN formation, and the increased planar zigzag content was confirmed through X-ray diffraction (XRD), electrical characterization, and Fourier transform infrared spectroscopy (FTIR) analyses. This study, for the first time, demonstrates that CNC addition to PAN enhances the mechanical properties and piezoelectric performance by promoting the formation of zigzag structures, which play a crucial role in the piezoelectric effect. The PAN–CNC composite holds great potential for applications in new piezoelectric devices. With CNC incorporation, the voltage increased by 68.9%, and the current increased by 80% compared to regular PAN. The generated energy is suitable for human applications and can also power commercial devices, making these findings pivotal for the advancement of piezoelectric materials and devices.
- Open Access
- 3 February 2025
- Published by Wiley in Advanced Science
- Vol. 12 (15) , e2414108
Fabrication of Graphene Polyhedra: Unveiling New Structures, Forms, and Properties
A hybrid nanoporous carbon alloy material is synthesized using a core–shell structure based on metal–organic frameworks, revealing a novel graphene polyhedral form. The presence of carbon and metal as doped cobalt carbides based on morphed graphene within the graphene polyhedra is confirmed through a combination of X‐ray diffraction, X‐ray photoelectron spectroscopy, transmission electron microscopy, and Raman spectroscopy analyses. These novel graphene polyhedra exhibit magnetoelectric coupling properties at room temperature. The magnetic state control is verified using a magnetic probe; the changes in the magnetic state increased with a higher applied bias, and the poling direction of the magnetic phase is reversed based on the scanning direction of the probe. This discovery holds promise for future applications in ultrafast devices and carbon‐based spintronics research.
- 3 February 2025
- Published by Wiley in Advanced Science
- Vol. 12 (15) , e2414108
Open AccessFabrication of Graphene Polyhedra: Unveiling New Structures, Forms, and Properties
A hybrid nanoporous carbon alloy material is synthesized using a core–shell structure based on metal–organic frameworks, revealing a novel graphene polyhedral form. The presence of carbon and metal as doped cobalt carbides based on morphed graphene within the graphene polyhedra is confirmed through a combination of X‐ray diffraction, X‐ray photoelectron spectroscopy, transmission electron microscopy, and Raman spectroscopy analyses. These novel graphene polyhedra exhibit magnetoelectric coupling properties at room temperature. The magnetic state control is verified using a magnetic probe; the changes in the magnetic state increased with a higher applied bias, and the poling direction of the magnetic phase is reversed based on the scanning direction of the probe. This discovery holds promise for future applications in ultrafast devices and carbon‐based spintronics research.