Jianmin Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jianmin Luo has a total of 195 co-authors. Here are the top co-authors by number of shared publications:
- Xinyong Tao
Zhejiang University of Technology
39 shared publications - Jianwei Nai
College of Materials Science and Engineering, Zhejiang University of Technology, Hangzhou, China
28 shared publications - Yujing Liu
College of Materials Science and Engineering, Zhejiang University of Technology, Hangzhou, China
28 shared publications - Yao Wang
College of Materials Science and Engineering, Zhejiang University of Technology, Hangzhou 310014, China
25 shared publications Huadong Yuan
College of Materials Science and Engineering, Zhejiang University of Technology, Hangzhou, China
22 shared publications- Shihui Zou
College of Materials Science and Engineering Zhejiang University of Technology Hangzhou China
16 shared publications
Latest Publications
- 16 October 2026
- Published by IOP Publishing in Nanotechnology
- Vol. 37 (42) , 425401
Ligand-engineered Ag nanoclusters-modified copper current collector for anode-free lithium metal battery
Anode-free lithium metal batteries (AFLMBs) exhibit significant potential for next-generation high-energy-density storage due to their inherently high energy density, low manufacturing cost and safety. However, non-uniform lithium nucleation and growth lead to the formation of lithium dendrites. These dendrites fracture readily during repeated plating/stripping cycles, transforming into electrochemically inert ‘dead lithium’ while mechanically disrupting the fragile solid electrolyte interface (SEI) layer and causing irreversible consumption of active lithium. Herein, a novel current collector is designed by decorating Cu with Ag nanoclusters bearing sulfur-containing ligands. The ligands, along with TFSI - decomposition, may contribute to the formation of a sulfur-rich SEI, while Ag nanoclusters provide lithiophilic nucleation sites for reversible lithium cycling. This design enables improved AFLMBs. Based on the design, the LiFePO 4 ||Cu–Ag NCs-2 anode-free battery demonstrates an average coulombic efficiency of above 99.7% over 100 cycles at 1 C. Also, a 1.2 Ah anode-free pouch cell was constructed with 275 Wh kg −1 .
- 16 October 2026
- Published by IOP Publishing in Nanotechnology
- Vol. 37 (42) , 425401
Ligand-engineered Ag nanoclusters-modified copper current collector for anode-free lithium metal battery
Anode-free lithium metal batteries (AFLMBs) exhibit significant potential for next-generation high-energy-density storage due to their inherently high energy density, low manufacturing cost and safety. However, non-uniform lithium nucleation and growth lead to the formation of lithium dendrites. These dendrites fracture readily during repeated plating/stripping cycles, transforming into electrochemically inert ‘dead lithium’ while mechanically disrupting the fragile solid electrolyte interface (SEI) layer and causing irreversible consumption of active lithium. Herein, a novel current collector is designed by decorating Cu with Ag nanoclusters bearing sulfur-containing ligands. The ligands, along with TFSI - decomposition, may contribute to the formation of a sulfur-rich SEI, while Ag nanoclusters provide lithiophilic nucleation sites for reversible lithium cycling. This design enables improved AFLMBs. Based on the design, the LiFePO 4 ||Cu–Ag NCs-2 anode-free battery demonstrates an average coulombic efficiency of above 99.7% over 100 cycles at 1 C. Also, a 1.2 Ah anode-free pouch cell was constructed with 275 Wh kg −1 .
- Open Access
- 15 October 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Regulating sodium deposition and interfacial chemistry via sulfur-embedded carbon spheres enables high-power Ah-level sodium-metal batteries
- 15 October 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Open AccessRegulating sodium deposition and interfacial chemistry via sulfur-embedded carbon spheres enables high-power Ah-level sodium-metal batteries
- Open Access
- 14 October 2026
- Published by Wiley in Carbon Energy
Research Progress on V 2 CT x MXene‐Based Composites: Synthetic Strategies, Structure Design, and Multifunctional Applications
V 2 CT x MXene, as an emerging member of two‐dimensional transition metal carbide/nitride family, has garnered significant attention for its exceptional electrochemical performance and tunable structural architecture, particularly in energy storage and conversion. This systematic overview elucidates the fundamental structure–property relationships of V 2 CT x MXene, highlighting its superior charge‐transfer kinetics, metallic conductivity, and cycling stability. A critical examination of state‐of‐the‐art synthesis methods is provided, along with a detailed discussion and analysis of their impacts on material properties. Moreover, advanced structural engineering approaches are highlighted, encompassing layered structure with enlarged interlayer spacing, surface functionalization, morphological tailoring, and hybrid composite construction. Meanwhile, this review systematically reveals the correlation between heterogeneous interfaces and the electronic, physical, and electrochemical properties of materials from the unique perspective of structural design strategies. Furthermore, the application prospects of V 2 CT x ‐based composites are comprehensively evaluated across electrochemical energy storage and conversion, as well as photocatalytic degradation of organic pollutants. Crucially, the underlying mechanisms governing charge storage processes and catalytic reaction pathways are elucidated. Finally, current challenges and future research directions are proposed, underscoring the broad potential and pivotal role of V 2 CT x ‐based composites across multiple domains.
- 14 October 2026
- Published by Wiley in Carbon Energy
Open AccessResearch Progress on V 2 CT x MXene‐Based Composites: Synthetic Strategies, Structure Design, and Multifunctional Applications
V 2 CT x MXene, as an emerging member of two‐dimensional transition metal carbide/nitride family, has garnered significant attention for its exceptional electrochemical performance and tunable structural architecture, particularly in energy storage and conversion. This systematic overview elucidates the fundamental structure–property relationships of V 2 CT x MXene, highlighting its superior charge‐transfer kinetics, metallic conductivity, and cycling stability. A critical examination of state‐of‐the‐art synthesis methods is provided, along with a detailed discussion and analysis of their impacts on material properties. Moreover, advanced structural engineering approaches are highlighted, encompassing layered structure with enlarged interlayer spacing, surface functionalization, morphological tailoring, and hybrid composite construction. Meanwhile, this review systematically reveals the correlation between heterogeneous interfaces and the electronic, physical, and electrochemical properties of materials from the unique perspective of structural design strategies. Furthermore, the application prospects of V 2 CT x ‐based composites are comprehensively evaluated across electrochemical energy storage and conversion, as well as photocatalytic degradation of organic pollutants. Crucially, the underlying mechanisms governing charge storage processes and catalytic reaction pathways are elucidated. Finally, current challenges and future research directions are proposed, underscoring the broad potential and pivotal role of V 2 CT x ‐based composites across multiple domains.
- 9 October 2026
- Published by Wiley in Advanced Materials
Host–Guest Engineering for Advanced Batteries
The performance of advanced batteries is governed not only by the intrinsic properties of electrodes and electrolytes, but also by the dynamic states of ionic, molecular, and reactive species during operation. Conventional materials‐centered strategies, however, often provide insufficient molecular‐level control over these local and transient states, limiting precise regulation of ion association, solvation/desolvation, interfacial transfer, and reaction‐intermediate conversion. Host–guest engineering offers a molecular design strategy to address this challenge by selectively recognizing, coordinating, confining, or redistributing target guests within defined host environments. This Review organizes host–guest engineering across liquid electrolytes, solid‐state and quasi‐solid‐state electrolytes, electrode–electrolyte interfaces, and solid–liquid conversion cathodes, and compares how different host environments regulate transport, interfacial chemistry, and conversion processes. A cross‐scenario quantitative comparison further links molecular‐level regulation with battery performance. Across these scenarios, effective regulation is shown to require an appropriate balance between guest‐regulation effectiveness and guest‐dynamic flexibility rather than simply maximizing binding or confinement. Finally, future opportunities are discussed in integrated host architectures, broader battery systems, adaptive host environments, and the quantitative determination of process‐specific host–guest interaction windows.
- 9 October 2026
- Published by Wiley in Advanced Materials
Host–Guest Engineering for Advanced Batteries
The performance of advanced batteries is governed not only by the intrinsic properties of electrodes and electrolytes, but also by the dynamic states of ionic, molecular, and reactive species during operation. Conventional materials‐centered strategies, however, often provide insufficient molecular‐level control over these local and transient states, limiting precise regulation of ion association, solvation/desolvation, interfacial transfer, and reaction‐intermediate conversion. Host–guest engineering offers a molecular design strategy to address this challenge by selectively recognizing, coordinating, confining, or redistributing target guests within defined host environments. This Review organizes host–guest engineering across liquid electrolytes, solid‐state and quasi‐solid‐state electrolytes, electrode–electrolyte interfaces, and solid–liquid conversion cathodes, and compares how different host environments regulate transport, interfacial chemistry, and conversion processes. A cross‐scenario quantitative comparison further links molecular‐level regulation with battery performance. Across these scenarios, effective regulation is shown to require an appropriate balance between guest‐regulation effectiveness and guest‐dynamic flexibility rather than simply maximizing binding or confinement. Finally, future opportunities are discussed in integrated host architectures, broader battery systems, adaptive host environments, and the quantitative determination of process‐specific host–guest interaction windows.
- 3 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (36) , 48956-48965
Ultrastable Lithium Metal Batteries Enabled by the Fluorinated Li/Electrolyte Interphase with High Mechanical Strength
A rationally designed solid-electrolyte interphase (SEI) is critical for enabling a high mechanical modulus, low mass transfer resistance, and uniform, rapid ion transport in lithium metal batteries. Herein, we report a promising artificial SEI layer fabricated by coating fluorinated hydroxyapatite on the commercially available polypropylene separator. Fluorination reaction for hydroxyapatite greatly improves its Young’s modulus, physically suppressing Li dendrite growth. More importantly, the uniformly coated nanoscale fluorinated hydroxyapatite with a solid−solid nanoporous network enables efficient Li-ion transport during Li plating/stripping and F− release, which not only endows the formed SEI with local outer regions of ordered laminar Li2O as revealed by cryo-transmission electron microscopy but also effectively promotes the formation of a stable LiF-rich inner layer. The obtained double-deck SEI, with high mechanical strength, suppresses SEI fracture during repeated cycles, promotes uniform Li-ion flux, and stabilizes the Li/electrolyte interface. As a result, Li anodes based on this fluorinated hydroxyapatite exhibit an ultrastable cycling life over 1200 h with a capacity of 3 mAh cm−2 at a current density of 3 mA cm−2. When coupled with a LiFePO4 cathode, the obtained full cell shows a high capacity retention of 96% after 600 cycles.
- 3 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (36) , 48956-48965
Ultrastable Lithium Metal Batteries Enabled by the Fluorinated Li/Electrolyte Interphase with High Mechanical Strength
A rationally designed solid-electrolyte interphase (SEI) is critical for enabling a high mechanical modulus, low mass transfer resistance, and uniform, rapid ion transport in lithium metal batteries. Herein, we report a promising artificial SEI layer fabricated by coating fluorinated hydroxyapatite on the commercially available polypropylene separator. Fluorination reaction for hydroxyapatite greatly improves its Young’s modulus, physically suppressing Li dendrite growth. More importantly, the uniformly coated nanoscale fluorinated hydroxyapatite with a solid−solid nanoporous network enables efficient Li-ion transport during Li plating/stripping and F− release, which not only endows the formed SEI with local outer regions of ordered laminar Li2O as revealed by cryo-transmission electron microscopy but also effectively promotes the formation of a stable LiF-rich inner layer. The obtained double-deck SEI, with high mechanical strength, suppresses SEI fracture during repeated cycles, promotes uniform Li-ion flux, and stabilizes the Li/electrolyte interface. As a result, Li anodes based on this fluorinated hydroxyapatite exhibit an ultrastable cycling life over 1200 h with a capacity of 3 mAh cm−2 at a current density of 3 mA cm−2. When coupled with a LiFePO4 cathode, the obtained full cell shows a high capacity retention of 96% after 600 cycles.
- 18 August 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (49) , 33705-33715
Mechanistic insights into enhanced Li + transport driven by Hf–O orbital hybridization in Hf-based oxychloride solid electrolytes
O 2− incorporation increases Li + concentration, strengthens Hf–O orbital hybridization, induces favorable local structural evolution, and thereby enhances ionic conductivity.
- 18 August 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (49) , 33705-33715
Mechanistic insights into enhanced Li + transport driven by Hf–O orbital hybridization in Hf-based oxychloride solid electrolytes
O 2− incorporation increases Li + concentration, strengthens Hf–O orbital hybridization, induces favorable local structural evolution, and thereby enhances ionic conductivity.
- 20 July 2026
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 11 (8) , 5706-5714
Reclaiming Inactive Lithium with a 2-Iodooctane Electrolyte Additive for Ultrastable Lithium Metal Batteries over a Two-Year Lifespan
A primary cause of the energy fading in high-energy-density lithium (Li) metal batteries is the accumulation of inactive Li, including inactive metallic Li caused by Li dendrite growth and Li compounds resulted from side reactions, which reduce anode utilization efficiency and hinder Li-ion transport. Therefore, it is crucial to develop electrolyte additives that can suppress Li dendrite growth and stabilize the interfacial structure. Here, we introduce 2-iodooctane into the electrolyte, which reacts at the anode and is oxidized at the cathode to generate the I3−/I− redox mediator that converts inactive Li to Li2O and recovers Li ions. Owing to the recovered inactive Li, the half-cells exhibit a high Coulombic efficiency of 99.03% with restrained Li dendrite growth. Accordingly, the symmetric cells perform tripled stability with an ultralong lifespan of 730 days at 2 mA cm−2, while the pouch cells retain an over 88% capacity after 100 cycles, demonstrating substantial commercial application potential.
- 20 July 2026
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 11 (8) , 5706-5714
Reclaiming Inactive Lithium with a 2-Iodooctane Electrolyte Additive for Ultrastable Lithium Metal Batteries over a Two-Year Lifespan
A primary cause of the energy fading in high-energy-density lithium (Li) metal batteries is the accumulation of inactive Li, including inactive metallic Li caused by Li dendrite growth and Li compounds resulted from side reactions, which reduce anode utilization efficiency and hinder Li-ion transport. Therefore, it is crucial to develop electrolyte additives that can suppress Li dendrite growth and stabilize the interfacial structure. Here, we introduce 2-iodooctane into the electrolyte, which reacts at the anode and is oxidized at the cathode to generate the I3−/I− redox mediator that converts inactive Li to Li2O and recovers Li ions. Owing to the recovered inactive Li, the half-cells exhibit a high Coulombic efficiency of 99.03% with restrained Li dendrite growth. Accordingly, the symmetric cells perform tripled stability with an ultralong lifespan of 730 days at 2 mA cm−2, while the pouch cells retain an over 88% capacity after 100 cycles, demonstrating substantial commercial application potential.
Polymerization‐Initiator Engineering Enables High‐Voltage‐Stable Gel Polymer Electrolytes for Lithium Metal Batteries
In situ polymerized gel polymer electrolytes (GPEs) have attracted much attention due to their high ionic conductivity and excellent interfacial contact. Among this type of GPEs, poly(1,3‐dioxane) (PDOX)‐based composite GPEs have emerged as a promising candidate for high‐energy‐density lithium metal batteries (LMBs) owing to their superior oxidative stability. However, uncontrolled lithium dendrite growth at the PDOX electrolyte/anode interface compromises interfacial stability and long‐term cycling durability. Here, indium trifluoromethanesulfonate (In(OTf) 3 ) is introduced as a bifunctional initiator to trigger the in situ polymerization of 1,3‐dioxane (DOX) to form a GPE. Meanwhile, it also yields a robust solid electrolyte interphase (SEI) enriched with Li x In alloy and LiF, generating a stable lithophilic and highly Li + ‐conductive interfacial layer that effectively suppresses lithium dendrite growth. As a result, the obtained PDOX electrolyte exhibits excellent stability, maintaining stable operation for over 1600 h at 1.0 mA cm −2 in a Li||Li symmetric cell. When paired with high‐voltage cathodes, the Li||NCM523 cells deliver a remarkable capacity retention of 82.5% after 500 cycles at 1 C. Importantly, an Ah‐level Li||NCM712 pouch cell delivers 402 Wh kg −1 energy density and demonstrates 99.3% capacity retention over 100 cycles, showcasing the potential of this GPE for practical applications.
Polymerization‐Initiator Engineering Enables High‐Voltage‐Stable Gel Polymer Electrolytes for Lithium Metal Batteries
In situ polymerized gel polymer electrolytes (GPEs) have attracted much attention due to their high ionic conductivity and excellent interfacial contact. Among this type of GPEs, poly(1,3‐dioxane) (PDOX)‐based composite GPEs have emerged as a promising candidate for high‐energy‐density lithium metal batteries (LMBs) owing to their superior oxidative stability. However, uncontrolled lithium dendrite growth at the PDOX electrolyte/anode interface compromises interfacial stability and long‐term cycling durability. Here, indium trifluoromethanesulfonate (In(OTf) 3 ) is introduced as a bifunctional initiator to trigger the in situ polymerization of 1,3‐dioxane (DOX) to form a GPE. Meanwhile, it also yields a robust solid electrolyte interphase (SEI) enriched with Li x In alloy and LiF, generating a stable lithophilic and highly Li + ‐conductive interfacial layer that effectively suppresses lithium dendrite growth. As a result, the obtained PDOX electrolyte exhibits excellent stability, maintaining stable operation for over 1600 h at 1.0 mA cm −2 in a Li||Li symmetric cell. When paired with high‐voltage cathodes, the Li||NCM523 cells deliver a remarkable capacity retention of 82.5% after 500 cycles at 1 C. Importantly, an Ah‐level Li||NCM712 pouch cell delivers 402 Wh kg −1 energy density and demonstrates 99.3% capacity retention over 100 cycles, showcasing the potential of this GPE for practical applications.
- Open Access
- 11 July 2026
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (32) , e71299
Synergistic Cation–Anion Engineering Enables Yttrium Chlorobromide Superionic Conductors for High‐Performance All‐Solid‐State Lithium Metal Batteries
Halide solid‐state electrolytes (HSSEs) deliver greater chemical stability, a wider electrochemical stability window, but lower room‐temperature ionic conductivities than existing sulfide solid‐state electrolytes. Herein, we report a novel HSSE, Li 2.5 Y 0.75 W 0.25 Cl 3.5 Br 2.5 , featuring synergetic anion–cation chemistry that enhances ionic conductivity and interfacial stability. The substitution of Br − at halide sites within Li 3 YCl 6 framework induces a space group transformation that expands the Li‐ion transport channels. Concurrently, the incorporation of W 5+ effectively generates cation vacancies and induces a cationic polarization effect, thereby reducing the energy barrier for Li‐ion migration. The resulting Li 2.5 Y 0.75 W 0.25 Cl 3.5 Br 2.5 achieves a high room‐temperature ionic conductivity of 6.38 mS cm −1 with a low activation energy of 0.22 eV. More importantly, the reaction products of WO 3 at the LiNi 0.8 Mn 0.1 Co 0.1 O 2 /Li 2.5 Y 0.75 W 0.25 Cl 3.5 Br 2.5 interface not only reduce the total interface energy but also significantly suppress oxygen release and enhance interfacial stability during cycling. Consequently, all‐solid‐state full cells paired with a LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode demonstrate long‐term cycling stability, with a high initial discharge capacity of 169.40 mAh g −1 at 0.3 C and a retained capacity of 100.14 mAh g −1 after 500 cycles. This work provides new insights into overcoming the performance limitations of HSSEs and holds significant importance for developing highly stable all solid‐state Li metal batteries (ASSLMBs).
- 11 July 2026
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (32) , e71299
Open AccessSynergistic Cation–Anion Engineering Enables Yttrium Chlorobromide Superionic Conductors for High‐Performance All‐Solid‐State Lithium Metal Batteries
Halide solid‐state electrolytes (HSSEs) deliver greater chemical stability, a wider electrochemical stability window, but lower room‐temperature ionic conductivities than existing sulfide solid‐state electrolytes. Herein, we report a novel HSSE, Li 2.5 Y 0.75 W 0.25 Cl 3.5 Br 2.5 , featuring synergetic anion–cation chemistry that enhances ionic conductivity and interfacial stability. The substitution of Br − at halide sites within Li 3 YCl 6 framework induces a space group transformation that expands the Li‐ion transport channels. Concurrently, the incorporation of W 5+ effectively generates cation vacancies and induces a cationic polarization effect, thereby reducing the energy barrier for Li‐ion migration. The resulting Li 2.5 Y 0.75 W 0.25 Cl 3.5 Br 2.5 achieves a high room‐temperature ionic conductivity of 6.38 mS cm −1 with a low activation energy of 0.22 eV. More importantly, the reaction products of WO 3 at the LiNi 0.8 Mn 0.1 Co 0.1 O 2 /Li 2.5 Y 0.75 W 0.25 Cl 3.5 Br 2.5 interface not only reduce the total interface energy but also significantly suppress oxygen release and enhance interfacial stability during cycling. Consequently, all‐solid‐state full cells paired with a LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode demonstrate long‐term cycling stability, with a high initial discharge capacity of 169.40 mAh g −1 at 0.3 C and a retained capacity of 100.14 mAh g −1 after 500 cycles. This work provides new insights into overcoming the performance limitations of HSSEs and holds significant importance for developing highly stable all solid‐state Li metal batteries (ASSLMBs).
Tailoring the Work Function of Oxyhalide Solid Electrolytes via Sulfur Doping to Boost High‐Performance All‐Solid‐State Lithium Batteries
Achieving high ionic conductivity alongside interfacial stability is essential yet challenging for solid‐state electrolytes. Here, we report a sulfur‐doped oxohalide solid‐state electrolyte, LiTaO 0.5 S 0.5 Cl 4 , synthesized via a facile high‐energy ball milling method. Confirmed by the experimental and theoretical simulation results, sulfur incorporation significantly elevates the work function and ionization energy to 4.54 and 8.0 eV, respectively, reducing electron availability for interfacial charge transfer and enhancing oxidative stability against high‐voltage cathodes. In addition, the coexistence of S 2− and O 2− promotes in‐situ formation of a Ta 2 O/TaS 2 composite protective layer, featuring high electronic insulation and low Li + migration barrier. Consequently, the all‐solid‐state Li battery delivers a high‐capacity retention of 75.5% after 500 cycles at 0.5 C using LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathodes. This work demonstrates that anion doping is an effective strategy for concurrently improving ionic conductivity and cathode interfacial stability.
Tailoring the Work Function of Oxyhalide Solid Electrolytes via Sulfur Doping to Boost High‐Performance All‐Solid‐State Lithium Batteries
Achieving high ionic conductivity alongside interfacial stability is essential yet challenging for solid‐state electrolytes. Here, we report a sulfur‐doped oxohalide solid‐state electrolyte, LiTaO 0.5 S 0.5 Cl 4 , synthesized via a facile high‐energy ball milling method. Confirmed by the experimental and theoretical simulation results, sulfur incorporation significantly elevates the work function and ionization energy to 4.54 and 8.0 eV, respectively, reducing electron availability for interfacial charge transfer and enhancing oxidative stability against high‐voltage cathodes. In addition, the coexistence of S 2− and O 2− promotes in‐situ formation of a Ta 2 O/TaS 2 composite protective layer, featuring high electronic insulation and low Li + migration barrier. Consequently, the all‐solid‐state Li battery delivers a high‐capacity retention of 75.5% after 500 cycles at 0.5 C using LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathodes. This work demonstrates that anion doping is an effective strategy for concurrently improving ionic conductivity and cathode interfacial stability.