Iida Pankka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Iida Pankka has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Pekka Taskinen
School of Chemical Engineering, Department of Chemical and Metallurgical Engineering, Aalto University, Espoo, Finland
5 shared publications - Daniel Lindberg
Department of Chemical and Metallurgical Engineering, Aalto University, Espoo, Finland
4 shared publications Joonas Tammela
3 shared publicationsDaniel Lindberg
1 shared publication- Jane Mulenshi
Division of Minerals and Metallurgical Engineering, Luleå University of Technology, SE-971 87 Luleå, Sweden
1 shared publication Justin Salminen
Boliden Kokkola, Kokkola, Finland
1 shared publication
Latest Publications
- Open Access
- 10 June 2026
- Published by Springer Nature in JOM
Refractory Wear in End-of-Life Peirce-Smith Converter Bricks
The lifespan of refractory linings is a major industrial concern for reasons of economics, safety, and online availability. The furnaces that pose the greatest challenges for refractory wear and lining life in copper smelting are batchwise-operating Peirce-Smith converters. In this study, refractory wear was investigated using three methods: laser flash analysis for thermal conductivity, X-ray computed microtomography for mesoscale 3D imaging, and SEM-EDS for phase structure. Three bricks were taken from the end-of-life brick lining of an industrial Peirce-Smith converter, after a campaign at the Boliden Rönnskär smelter (Sweden). Thermal diffusivity was measured from room temperature to 800°C. Specific heat and density were calculated using FactSage based on X-ray computed microtomography results. For two of the bricks, infiltration extended to 60–70 mm and porosity increased sharply after the infiltration zone. The infiltration was found to consist mostly of Cu and Cu 2 S. Whether the infiltration consisted of Cu or Cu 2 S had only a minimal effect on the thermal conductivity, whereas the effects of porosity were more noticeable.
- 10 June 2026
- Published by Springer Nature in JOM
Open AccessRefractory Wear in End-of-Life Peirce-Smith Converter Bricks
The lifespan of refractory linings is a major industrial concern for reasons of economics, safety, and online availability. The furnaces that pose the greatest challenges for refractory wear and lining life in copper smelting are batchwise-operating Peirce-Smith converters. In this study, refractory wear was investigated using three methods: laser flash analysis for thermal conductivity, X-ray computed microtomography for mesoscale 3D imaging, and SEM-EDS for phase structure. Three bricks were taken from the end-of-life brick lining of an industrial Peirce-Smith converter, after a campaign at the Boliden Rönnskär smelter (Sweden). Thermal diffusivity was measured from room temperature to 800°C. Specific heat and density were calculated using FactSage based on X-ray computed microtomography results. For two of the bricks, infiltration extended to 60–70 mm and porosity increased sharply after the infiltration zone. The infiltration was found to consist mostly of Cu and Cu 2 S. Whether the infiltration consisted of Cu or Cu 2 S had only a minimal effect on the thermal conductivity, whereas the effects of porosity were more noticeable.
- Open Access
- 29 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (6) , 7428-7435
Thermal conductivity of used copper converter bricks
- 29 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (6) , 7428-7435
Open AccessThermal conductivity of used copper converter bricks
- Open Access
- 14 March 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 11 (2) , 1431-1441
Thermal Conductivity of Industrial Ladle Slag Linings
Protective linings are commonly used to prolong the service life of transfer ladles and prevent operational issues. Slag linings are an old and sustainable chromia-free option as slag from the smelter is used to make the lining. In this work, thermal properties and structure of two different ladle slag linings from Boliden Harjavalta were measured using laser-flash analysis and mineralogical techniques. The linings were found to consist mostly of fayalite and magnetite with some entrained copper matte droplets and glass. They included an amorphous layer right against the ladle wall and a textured crystalline layer. The matte transfer ladle slag linings also included a growth layer on top of the coarse-grained crystalline layer. The thermal diffusivity of the linings was measured using LFA. Density was modeled using MTDATA software, and specific heat calculated from thermal diffusivity measurements using a reference sample. These three factors were used to calculate the thermal conductivity. The thermal conductivity of the linings was calculated to be between 1.5 and 2.1 W/(m·K) in a temperature range of 22–800 °C. Graphical Abstract
- 14 March 2025
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 11 (2) , 1431-1441
Open AccessThermal Conductivity of Industrial Ladle Slag Linings
Protective linings are commonly used to prolong the service life of transfer ladles and prevent operational issues. Slag linings are an old and sustainable chromia-free option as slag from the smelter is used to make the lining. In this work, thermal properties and structure of two different ladle slag linings from Boliden Harjavalta were measured using laser-flash analysis and mineralogical techniques. The linings were found to consist mostly of fayalite and magnetite with some entrained copper matte droplets and glass. They included an amorphous layer right against the ladle wall and a textured crystalline layer. The matte transfer ladle slag linings also included a growth layer on top of the coarse-grained crystalline layer. The thermal diffusivity of the linings was measured using LFA. Density was modeled using MTDATA software, and specific heat calculated from thermal diffusivity measurements using a reference sample. These three factors were used to calculate the thermal conductivity. The thermal conductivity of the linings was calculated to be between 1.5 and 2.1 W/(m·K) in a temperature range of 22–800 °C. Graphical Abstract
- Open Access
- 3 September 2024
- Published by Springer Nature in JOM
- Vol. 76 (11) , 6650-6659
Investigation of End-of-Life Chrome-Magnesia Refractories Using X-Ray Computed Tomography
The lifespan of refractory linings is a major industrial concern for safety, on-line availability, and financial reasons. In copper smelting, batchwise operating matte converters are the furnaces that pose the greatest challenge when it comes to refractory wear and lining life. In this work, the structure and morphology of used magnesia–chrome bricks were studied using X-ray computed tomography and mineralogical techniques. The bricks were taken from various locations of an end-of-life brick lining of an industrial Peirce–Smith converter, after a normal campaign at Boliden Harjavalta smelter (Finland). The results show that it is possible to visualize in 3D, e.g., porosity, metal-containing phases, and refractory magnesia in the used bricks. Different digital images, such as cross-sections and average volume fractions, were used as a non-destructive method to characterize the bricks’ internal structure. The metal/matte infiltration in the open porosity was found to differ based on the location in the converter, with some bricks having no metal/matte infiltration and the tuyere line showing metal/matte infiltration at a depth of about 100 mm from the hot face.
- 3 September 2024
- Published by Springer Nature in JOM
- Vol. 76 (11) , 6650-6659
Open AccessInvestigation of End-of-Life Chrome-Magnesia Refractories Using X-Ray Computed Tomography
The lifespan of refractory linings is a major industrial concern for safety, on-line availability, and financial reasons. In copper smelting, batchwise operating matte converters are the furnaces that pose the greatest challenge when it comes to refractory wear and lining life. In this work, the structure and morphology of used magnesia–chrome bricks were studied using X-ray computed tomography and mineralogical techniques. The bricks were taken from various locations of an end-of-life brick lining of an industrial Peirce–Smith converter, after a normal campaign at Boliden Harjavalta smelter (Finland). The results show that it is possible to visualize in 3D, e.g., porosity, metal-containing phases, and refractory magnesia in the used bricks. Different digital images, such as cross-sections and average volume fractions, were used as a non-destructive method to characterize the bricks’ internal structure. The metal/matte infiltration in the open porosity was found to differ based on the location in the converter, with some bricks having no metal/matte infiltration and the tuyere line showing metal/matte infiltration at a depth of about 100 mm from the hot face.
- Open Access
- 13 January 2023
- Published by Springer Nature in JOM
- Vol. 75 (6) , 2026-2033
Thermodynamic Modeling of Elemental Distributions of Trace Elements in Non-ferrous Iron Residue Hydrogen Reduction
Every year millions of tons of iron residue are generated as a by-product of zinc production. Stabilized landfilled iron residue contains recoverable metals that could be valorized with further processing. Pyrometallurgical processing allows the recovery of valuable metals while simultaneously producing a clean slag that can then be further utilized. A thermodynamic model was developed with FactSage version 8.0. The focus was on minor element behavior and distribution of elements between phases. Calculations were performed at 1200–1400°C and pressure of 1 atm with both pure H2 and H2-Ar mixtures used as a reductant. Also, the concentrations of Pb and Zn in the input were varied. The results showed that a liquid alloy phase forms consisting mostly of either Cu, As and Pb or Fe, As and Cu. It was noted that a higher Ar total gas amount in reduction decreased the mass fraction of the liquid alloy and increased the evaporation of elements into fume dust. S, Bi, Pb, Ge and Zn were observed to evaporate fully, while As, In, Sb and Ag evaporated only partially. The results need to be verified experimentally.
- 13 January 2023
- Published by Springer Nature in JOM
- Vol. 75 (6) , 2026-2033
Open AccessThermodynamic Modeling of Elemental Distributions of Trace Elements in Non-ferrous Iron Residue Hydrogen Reduction
Every year millions of tons of iron residue are generated as a by-product of zinc production. Stabilized landfilled iron residue contains recoverable metals that could be valorized with further processing. Pyrometallurgical processing allows the recovery of valuable metals while simultaneously producing a clean slag that can then be further utilized. A thermodynamic model was developed with FactSage version 8.0. The focus was on minor element behavior and distribution of elements between phases. Calculations were performed at 1200–1400°C and pressure of 1 atm with both pure H2 and H2-Ar mixtures used as a reductant. Also, the concentrations of Pb and Zn in the input were varied. The results showed that a liquid alloy phase forms consisting mostly of either Cu, As and Pb or Fe, As and Cu. It was noted that a higher Ar total gas amount in reduction decreased the mass fraction of the liquid alloy and increased the evaporation of elements into fume dust. S, Bi, Pb, Ge and Zn were observed to evaporate fully, while As, In, Sb and Ag evaporated only partially. The results need to be verified experimentally.