Huiying Xiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Huiying Xiang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bo Li
Institute of Electric Power Science of Guizhou Power Grid Co., Ltd., Guiyang 550002, China
3 shared publications - Yuan Yuan
College of Materials Science and Engineering Chongqing University Chongqing China
3 shared publications - Jie Bai
Institute of Electric Power Science of Guizhou Power Grid Co., Ltd., Guiyang 550002, China
2 shared publications - Tao Zhu
College of Materials Science and Engineering, Chongqing University, Chongqing 400030, China
2 shared publications - Xu Dai
State Key Laboratory of Power Transmission Equipment & System Security and New Technology, Chongqing University, Chongqing 400044, China
2 shared publications - Xujiang Hua
College of Materials Science and Engineering, Chongqing University, Chongqing 400030, China
2 shared publications
Latest Publications
- Open Access
A Superhydrophobic Anti-Icing Surface with a Honeycomb Nanopore Structure
Recently, the icing disaster of transmission lines has been a serious threat to the safe operation of the power system. A superhydrophobic (SHP) anti-icing surface with a honeycomb nanopore structure was constructed using anodic oxidation technology combined with a vacuum infusion process. When the current density was 87.5 mA/cm2, the honeycomb porous surface had the best superhydrophobic performance (excellent water mobility), lowest ice-adhesion strength (0.7 kPa) and best anti-frosting performance. Compared with other types of alumina surfaces, the ice-adhesion strength of the SHP surface (87.5 mA/cm2) was only 0.2% of that of the bare surface. The frosting time of the SHP surface (87.5 mA/cm2) was 150 min, which was much slower. The former is attributed to the air cushion within the porous structure and the stress concentration, and the latter is attributed to the self-transition of the droplets and low solid–liquid heat transfer area. After 100 icing or frosting cycles, the SHP surface (87.5 mA/cm2) maintained a low ice-adhesion strength and superhydrophobic performance. This is because the anodic oxidation process forms a hard porous film, and the nano porous structure with a high aspect ratio can store modifiers to realize self-healing. The results indicate that the SHP surface with a honeycomb nanopore structure presents excellent anti-icing performance and durability.
Open AccessA Superhydrophobic Anti-Icing Surface with a Honeycomb Nanopore Structure
Recently, the icing disaster of transmission lines has been a serious threat to the safe operation of the power system. A superhydrophobic (SHP) anti-icing surface with a honeycomb nanopore structure was constructed using anodic oxidation technology combined with a vacuum infusion process. When the current density was 87.5 mA/cm2, the honeycomb porous surface had the best superhydrophobic performance (excellent water mobility), lowest ice-adhesion strength (0.7 kPa) and best anti-frosting performance. Compared with other types of alumina surfaces, the ice-adhesion strength of the SHP surface (87.5 mA/cm2) was only 0.2% of that of the bare surface. The frosting time of the SHP surface (87.5 mA/cm2) was 150 min, which was much slower. The former is attributed to the air cushion within the porous structure and the stress concentration, and the latter is attributed to the self-transition of the droplets and low solid–liquid heat transfer area. After 100 icing or frosting cycles, the SHP surface (87.5 mA/cm2) maintained a low ice-adhesion strength and superhydrophobic performance. This is because the anodic oxidation process forms a hard porous film, and the nano porous structure with a high aspect ratio can store modifiers to realize self-healing. The results indicate that the SHP surface with a honeycomb nanopore structure presents excellent anti-icing performance and durability.
- Open Access
Effects of the Second Anodization Parameters on the Hydrophobicity and Anti-Icing Properties of Al Surface with Composite Nanopore Structure
Icing on transmission lines often causes potential electric damage in power systems. Superhydrophobic anodized Al conductors have been proposed to have good anti-icing properties. In this study, superhydrophobic anodized Al conductors with composite nanopore structures were prepared by a two-step anodization. The microstructure, hydrophobicity, and anti-icing properties of composite nanopore structures were compared and studied. The optimal preparation parameter was determined as a current density of 0.04375 A/cm2 and anodization time of 15 min. Compared with the bare substrate, the optimal anodized Al surface of the composite nanopore structures show excellent hydrophobic and anti-icing properties, including a contact angle of 173°, a contact angle hysteresis of 0.122°, an ice adhesion strength of 0.71 kPa, and a glaze icing weight of 0.1 g after the 8 h. Therefore, the prepared anodized Al surface of composite nanopore structures with good anti-icing properties has profound application potential for overhead transmission lines.
Open AccessEffects of the Second Anodization Parameters on the Hydrophobicity and Anti-Icing Properties of Al Surface with Composite Nanopore Structure
Icing on transmission lines often causes potential electric damage in power systems. Superhydrophobic anodized Al conductors have been proposed to have good anti-icing properties. In this study, superhydrophobic anodized Al conductors with composite nanopore structures were prepared by a two-step anodization. The microstructure, hydrophobicity, and anti-icing properties of composite nanopore structures were compared and studied. The optimal preparation parameter was determined as a current density of 0.04375 A/cm2 and anodization time of 15 min. Compared with the bare substrate, the optimal anodized Al surface of the composite nanopore structures show excellent hydrophobic and anti-icing properties, including a contact angle of 173°, a contact angle hysteresis of 0.122°, an ice adhesion strength of 0.71 kPa, and a glaze icing weight of 0.1 g after the 8 h. Therefore, the prepared anodized Al surface of composite nanopore structures with good anti-icing properties has profound application potential for overhead transmission lines.
- Open Access
Water-Droplet Impact and Sliding Behaviors on Slippery Surfaces with Various Weber Numbers and Surface Inclinations
The dynamic behaviors of water droplets on a slippery surface are significant to practical anti-icing applications. Herein, the impact and sliding behavior of water droplets on lubricant-infused surfaces (LISs) were investigated with a high-speed camera. LISs were prepared by infusing perfluoropolyether oils into anodized porous surfaces. The results show that the maximum spreading diameter and retraction velocity of the impact droplet increased with the We number. For LIS-100, the spreading factor at 2.5 ms increased from 2.00 to 3.88 with We increasing from 30 to 267. Low-viscosity lubricant facilitated the retraction speed and rebound of droplet impact on the surface, while high-viscosity lubricant contributed to the lubricant stability of the LIS. Additionally, high inclination angle (θ) facilitated the rapid shedding of water droplets on the surface. The velocity increased rapidly from 1.04 to 4.66 mm/s with θ increasing from 15° to 45°. The LIS prepared with low-viscosity lubricant had a high sliding velocity, and the sliding velocity of water droplets on LIS-100 was about seven times faster than that on LIS-104. This work reveals the impacting law of water droplets on LISs and provides useful information for the design of LISs under drop impact conditions.
Open AccessWater-Droplet Impact and Sliding Behaviors on Slippery Surfaces with Various Weber Numbers and Surface Inclinations
The dynamic behaviors of water droplets on a slippery surface are significant to practical anti-icing applications. Herein, the impact and sliding behavior of water droplets on lubricant-infused surfaces (LISs) were investigated with a high-speed camera. LISs were prepared by infusing perfluoropolyether oils into anodized porous surfaces. The results show that the maximum spreading diameter and retraction velocity of the impact droplet increased with the We number. For LIS-100, the spreading factor at 2.5 ms increased from 2.00 to 3.88 with We increasing from 30 to 267. Low-viscosity lubricant facilitated the retraction speed and rebound of droplet impact on the surface, while high-viscosity lubricant contributed to the lubricant stability of the LIS. Additionally, high inclination angle (θ) facilitated the rapid shedding of water droplets on the surface. The velocity increased rapidly from 1.04 to 4.66 mm/s with θ increasing from 15° to 45°. The LIS prepared with low-viscosity lubricant had a high sliding velocity, and the sliding velocity of water droplets on LIS-100 was about seven times faster than that on LIS-104. This work reveals the impacting law of water droplets on LISs and provides useful information for the design of LISs under drop impact conditions.