JCJinhang Chen

Jinhang Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jinhang Chen has a total of 68 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Rapid electrothermal rejuvenation of spent lithium cobalt oxide cathode

    by Yi Cheng, Jinhang Chen, Weiyin Chen, Qiming Liu, Obinna E. Onah, Zicheng Wang, Gang Wu, Tianyou Xie, Lucas Eddy, Boris I. Yakobson, et al.

    Increasing use of lithium-ion batteries has triggered intensive attention to the management of end-of-life batteries. Sustainable recycling of high-value cathode materials is needed to address resource depletion and environmental challenges. Traditional battery recycling methods, including pyro- and hydro-metallurgical methods, are material-destructive processes with substantial time, energy, and chemical consumption. Here, we develop a rapid and effective electrothermal method to rejuvenate spent lithium cobalt oxide cathodes within 30 s. By incorporating Mg and Al for surface engineering during the process, the structural stability of the regenerated cathode is enhanced by mitigating detrimental phase transformations at high voltage. Thus, the upcycled cathode exhibits a high capacity of ∼203 mA h g−1 at 0.2C at an elevated cut-off voltage of 4.6 V, and maintains 84% of the initial capacity after 200 cycles. According to life cycle assessment and techno-economic analysis, our process exhibits significantly reduced environmental impacts with lower energy consumption, greenhouse gas emission, capital, and operating cost, and no solvent usage, making it a promising route to further upcycle other battery materials towards a circular economy.


  • Coupling Amorphization and Compositional Optimization of Ternary Metal Phosphides toward High-Performance Electrocatalytic Hydrogen Production

    by Bing Deng, Zhen-Yu Wu, Erkang Feng, Lu Ma, Zhe Wang, Jinhang Chen, Lucas Eddy, Alexander Lathem, Teng Wang, Weiyin Chen, et al.

    Amorphous materials, with abundant active sites and unique electronic configurations, have the potential to outperform their crystalline counterparts in high-performance catalysis for clean energy. However, their synthesis and compositional optimization remain underexplored due to the strict conditions required for their formation. Here, we report the synthesis of ternary platinum-nickel-phosphorus (PtNiP) amorphous nanoparticles (ANPs) within milliseconds by flash Joule heating, which features ultrafast cooling that enables the vitrification of metal precursors. Through compositional optimization, the Gibbs free energy of hydrogen adsorption for Pt4Ni4P1 ANPs is optimized at 0.02 eV, an almost ideal value, even surpassing that of the benchmark metallic platinum catalyst. As a result, the PtNiP ANPs exhibited superior activity in electrocatalytic hydrogen evolution in acid electrolyte (η10 ∼ 14 mV, Tafel slope ∼ 18 mV dec-1, and mass activity 5× higher than state-of-the-art Pt/C). Life-cycle assessment and technoeconomic analysis suggest that, compared to existing processes, our approach enables notable reductions in greenhouse gas emission, energy consumption, and production cost for practical electrolyzer catalyst manufacturing.


  • Cathode‐Electrolyte Interphase Engineering toward Fast‐Charging LiFePO4 Cathodes by Flash Carbon Coating

    by Jinhang Chen, Obinna E. Onah, Yi Cheng, Karla J. Silva, Chi Hun (Will) Choi, Weiyin Chen, Shichen Xu, Lucas Eddy, Yimo Han, Boris I. Yakobson, et al.

    Lithium iron phosphate (LiFePO4, LFP) batteries are widely used in electric vehicles and energy storage systems due to their excellent cycling stability, affordability and safety. However, the rate performance of LFP remains limited due to its low intrinsic electronic and ionic conductivities. In this work, an ex situ flash carbon coating method is developed to enhance the interfacial properties for fast charging. A continuous, amorphous carbon layer is achieved by rapidly decomposing the precursors and depositing carbon species in a confined space within 10 s. Simultaneously, different heteroatoms can be introduced into the surface carbon matrix, which regulates the irregular growth of cathode‐electrolyte interphase (CEI) and selectively facilitates the inorganic region formation. The inorganic‐rich, hybrid conductive CEI not only promotes electron and ion transport but also restricts parasitic side reactions. Consequently, LFP cathodes with fluorinated carbon coatings exhibited the highest capacity of 151 mAh g−1 at 0.2 C and 96 mAh g−1 at 10 C, indicating their excellent rate capability over commercial LFP (58 mAh g−1 at 10 C). This solvent‐free, versatile surface modification is shown for other electrode materials, providing an efficient platform for electrode‐electrolyte interphase engineering through a surface post‐treatment.


  • Open Access

    Nondestructive flash cathode recycling

    by Weiyin Chen, Yi Cheng, Jinhang Chen, Ksenia V. Bets, Rodrigo V. Salvatierra, Chang Ge, John Tianci Li, Duy Xuan Luong, Carter Kittrell, Zicheng Wang, et al.

    Effective recycling of end-of-life Li-ion batteries (LIBs) is essential due to continuous accumulation of battery waste and gradual depletion of battery metal resources. The present closed-loop solutions include destructive conversion to metal compounds, by destroying the entire three-dimensional morphology of the cathode through continuous thermal treatment or harsh wet extraction methods, and direct regeneration by lithium replenishment. Here, we report a solvent- and water-free flash Joule heating (FJH) method combined with magnetic separation to restore fresh cathodes from waste cathodes, followed by solid-state relithiation. The entire process is called flash recycling. This FJH method exhibits the merits of milliseconds of duration and high battery metal recovery yields of ~98%. After FJH, the cathodes reveal intact core structures with hierarchical features, implying the feasibility of their reconstituting into new cathodes. Relithiated cathodes are further used in LIBs, and show good electrochemical performance, comparable to new commercial counterparts. Life-cycle-analysis highlights that flash recycling has higher environmental and economic benefits over traditional destructive recycling processes.


  • Open Access

    Electrothermal mineralization of per- and polyfluoroalkyl substances for soil remediation

    by Yi Cheng, Bing Deng, Phelecia Scotland, Lucas Eddy, Arman Hassan, Bo Wang, Karla J. Silva, Bowen Li, Kevin M. Wyss, Mine G. Ucak-Astarlioglu, et al.

    Per- and polyfluoroalkyl substances (PFAS) are persistent and bioaccumulative pollutants that can easily accumulate in soil, posing a threat to environment and human health. Current PFAS degradation processes often suffer from low efficiency, high energy and water consumption, or lack of generality. Here, we develop a rapid electrothermal mineralization (REM) process to remediate PFAS-contaminated soil. With environmentally compatible biochar as the conductive additive, the soil temperature increases to >1000 °C within seconds by current pulse input, converting PFAS to calcium fluoride with inherent calcium compounds in soil. This process is applicable for remediating various PFAS contaminants in soil, with high removal efficiencies ( >99%) and mineralization ratios ( >90%). While retaining soil particle size, composition, water infiltration rate, and cation exchange capacity, REM facilitates an increase of exchangeable nutrient supply and arthropod survival in soil, rendering it superior to the time-consuming calcination approach that severely degrades soil properties. REM is scaled up to remediate soil at two kilograms per batch and promising for large-scale, on-site soil remediation. Life-cycle assessment and techno-economic analysis demonstrate REM as an environmentally friendly and economic process, with a significant reduction of energy consumption, greenhouse gas emission, water consumption, and operation cost, when compared to existing soil remediation practices.


  • Top Cited Papers

    Flash upcycling of waste glass fibre-reinforced plastics to silicon carbide

    by Yi Cheng, Jinhang Chen, Bing Deng, Weiyin Chen, Karla J. Silva, Lucas Eddy, Gang Wu, Ying Chen, Bowen Li, Carter Kittrell, et al.


  • Kinetically Controlled Synthesis of Metallic Glass Nanoparticles with Expanded Composition Space

    by Bing Deng, Zhe Wang, Chi Hun Choi, Gang Li, Zhe Yuan, Jinhang Chen, Duy Xuan Luong, Lucas Eddy, Bongki Shin, Alexander Lathem, et al.

    Nanoscale metallic glasses offer opportunities for investigating fundamental properties of amorphous solids and technological applications in biomedicine, microengineering, and catalysis. However, their top‐down fabrication is limited by bulk counterpart availability, and bottom‐up synthesis remains underexplored due to strict formation conditions. Here, a kinetically controlled flash carbothermic reaction is developed, featuring ultrafast heating (>105 K s−1) and cooling rates (>104 K s−1), for synthesizing metallic glass nanoparticles within milliseconds. Nine compositional permutations of noble metals, base metals, and metalloid (M1─M2─P, M1 = Pt/Pd, M2 = Cu/Ni/Fe/Co/Sn) are synthesized with widely tunable particle sizes and substrates. Through combinatorial development, a substantially expanded composition space for nanoscale metallic glass is discovered compared to bulk counterpart, revealing that the nanosize effect enhances glass forming ability. Leveraging this, several nanoscale metallic glasses are synthesized with composition that have never, to the knowledge, been synthesized in bulk. The metallic glass nanoparticles exhibit high activity in heterogeneous catalysis, outperforming crystalline metal alloy nanoparticles.


  • Cathode Interface Construction by Rapid Sintering in Solid‐State Batteries

    by Jinhang Chen, Weiyin Chen, Bing Deng, Bowen Li, Carter Kittrell, James M. Tour

    Solid‐state batteries (SSBs) are poised to replace traditional organic liquid‐electrolyte lithium‐ion batteries due to their higher safety and energy density. Oxide‐based solid electrolytes (SEs) are particularly attractive for their stability in air and inability to ignite during thermal runaway. However, achieving high‐performance in oxide‐based SSBs requires the development of an intimate and robust SE–cathode interface to overcome typically large interfacial resistances. The transition interphase should be both physically and chemically active. This study presents a thin, conductive interphase constructed between lithium aluminum titanium phosphate and lithium cobalt oxide using a rapid sintering method that modifies the interphase within 10 s. The rapid heating and cooling rates restrict side reactions and interdiffusion on the interface. SSBs with thick composite cathodes demonstrate a high initial capacity of ≈120 mAh g−1 over 200 cycles at room temperature. Furthermore, the rapid sintering method can be extended to other cathode systems under similar conditions. These findings highlight the importance of constructing an appropriate SE–cathode interface and provide insight into designing practical SSBs.


  • Open Access

    Battery metal recycling by flash Joule heating

    by Weiyin Chen, Jinhang Chen, Ksenia V. Bets, Rodrigo V. Salvatierra, Kevin M. Wyss, Guanhui Gao, Chi Hun Choi, Bing Deng, Xin Wang, John Tianci Li, et al.

    The staggering accumulation of end-of-life lithium-ion batteries (LIBs) and the growing scarcity of battery metal sources have triggered an urgent call for an effective recycling strategy. However, it is challenging to reclaim these metals with both high efficiency and low environmental footprint. We use here a pulsed dc flash Joule heating (FJH) strategy that heats the black mass, the combined anode and cathode, to >2100 kelvin within seconds, leading to ~1000-fold increase in subsequent leaching kinetics. There are high recovery yields of all the battery metals, regardless of their chemistries, using even diluted acids like 0.01 M HCl, thereby lessening the secondary waste stream. The ultrafast high temperature achieves thermal decomposition of the passivated solid electrolyte interphase and valence state reduction of the hard-to-dissolve metal compounds while mitigating diffusional loss of volatile metals. Life cycle analysis versus present recycling methods shows that FJH significantly reduces the environmental footprint of spent LIB processing while turning it into an economically attractive process.


  • Upcycling of Waste Plastic into Hybrid Carbon Nanomaterials

    by Kevin M. Wyss, John T. Li, Paul A. Advincula, Ksenia V. Bets, Weiyin Chen, Lucas Eddy, Karla J. Silva, Jacob L. Beckham, Jinhang Chen, Wei Meng, et al.

    Graphitic 1D and hybrid nanomaterials represent a powerful solution in composite and electronic applications due to exceptional properties, but large‐scale synthesis of hybrid materials has yet to be realized. Here, a rapid, scalable method to produce graphitic 1D materials from polymers using flash Joule heating (FJH) is reported. This avoids lengthy chemical vapor deposition and uses no solvent or water. The flash 1D materials (F1DM), synthesized using a variety of earth‐abundant catalysts, have controllable diameters and morphologies by parameter tuning. Furthermore, the process can be modified to form hybrid materials, with F1DM bonded to turbostratic graphene. In nanocomposites, F1DM outperform commercially available carbon nanotubes. Compared to current 1D material synthetic strategies using life cycle assessment, FJH synthesis represents an 86–92% decrease in cumulative energy demand and 92–94% decrease in global‐warming potential. This work suggests that FJH affords a cost‐effective and sustainable route to upcycle waste plastic into valuable 1D and hybrid nanomaterials.