ZAZuliahani Ahmad

Zuliahani Ahmad

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zuliahani Ahmad has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization of carbon black and graphite filled epoxy conductive ink via green solvent method

    by Diana Mohamad Kamsani, Zuliahani Ahmad, Helyati Abu Hassan Shaari, Pham Trung Kien, Muhammad Mahyiddin Ramli

    Conductive ink is gaining attention in the electronics industry due to its affordability, simplicity, and environmentally friendly properties. This study aimed to analyze a conductive ink made with Carbon Black (CB) and Graphite (G) as fillers, with epoxy resin as the binder and a green co-solvent of ethanol and distilled water. Various characterization techniques were used to examine the fillers. X-ray diffraction (XRD) revealed that CB exhibited an amorphous region at the (002) peak around 21.1°, while G showed distinct peaks at 26.5° and 54.4°, indicating a well-ordered graphitic structure. UV-Vis analysis showed that both CB and G interacted with the epoxy matrix, with an absorption peak in the 270-280 nm range corresponding to π–π* transitions. Fourier-transform infrared (FTIR) spectroscopy confirmed this interaction, with the presence of hydroxyl groups (2800–3500 cm⁻¹) and carboxyl group vibrations at 1241 cm⁻¹, indicating bonding between the polymer and filler. The dispersion of the fillers in the epoxy matrix was examined using Field Emission Scanning Electron Microscope (FESEM), which also assessed agglomeration. The ink's conductivity was tested according to ASTM F390 standards, with optimal CB loading at 4% achieving a conductivity of 4.49 × 10⁻⁵ S/m and optimal G loading at 3% yielding a conductivity of 7.14 × 10⁻⁵ S/m. These results indicate that G-based conductive ink with 3% loading performs better than CB-based ink for printed electronics applications.


  • Open Access

    Characterization, Physicomechanical and Corrosion Properties of Reinforced Microcrystalline Cellulose Treated Silane Unsaturated Polyester Primer Coatings.

    by Adzrie Baharudin, Zuliahani Ahmad, Ayu Azellia Anuar, Nur Dina Adlina Azmani, Angelene Betsy Mura, Siti Hana Humaira Rustam, Muhamed Syaheen Azhar, Siti Nor Din

    Corrosion has been a major universal issue due to failure of building structures and high maintenance. The utilization of unsaturated polyester (UPE) as primer coating is insufficient to inhibit the corrosion. Hence, microcrystalline cellulose (MCC) had been incorporated into UPE as a reinforcement filler for the production of primer coatings, due to its high crystalline region in the structure. The objectives of this study were to investigate the physical, mechanical, and corrosive properties of various MCC loadings (0, 3, 6, 9, 12 and 15 wt%) reinforced UPE applied on metal substrates and determine the effect of silane treatment (MCC-APTES) on MCC reinforcement used in UPE-MCC coating for primer application. The coating properties were studied for adhesion, mechanical and corrosive properties using pencil hardness, adhesion tape and immersion tests. At 6% MCC-APTES loading showed improvement in mechanical and adhesion properties at 6H grade and less than 5 % pull out test for pencil hardness and adhesion tests respectively. Whilst the immersion test demonstrated that at 6% MCC-APTES of loading gives optimum corrosion resistant where no corrosion found as compared to the control sample as supported by the improved interaction shown in FTIR spectrum. Therefore, it was evidenced that at 6% of MCC-APTES has significant potential as a reinforcement filler and promotes enhanced mechanical, adhesion, and corrosion properties as compared to other formulations.

  • Open Access

    Correction: Nordin et al. The State of the Art of Natural Polymer Functionalized Fe3O4 Magnetic Nanoparticle Composites for Drug Delivery Applications: A Review. Gels 2023, 9, 121

    by Abu Hassan Nordin, Zuliahani Ahmad, Siti Muhamad Nur Husna, Rushdan Ahmad Ilyas, Ahmad Khusairi Azemi, Noraznawati Ismail, Muhammad Luqman Nordin, Norzita Ngadi, Nordin Hawa Siti, Walid Nabgan, et al.

  • Open Access

    Recent Advances in Using Adsorbent Derived from Agricultural Waste for Antibiotics and Non-Steroidal Anti-Inflammatory Wastewater Treatment: A Review

    by Abu Hassan Nordin, Abdul Samad Norfarhana, Siti Fadilla Md Noor, Syafikah Huda Paiman, Muhammad Luqman Nordin, Siti Muhamad Nur Husna, Rushdan Ahmad Ilyas, Norzita Ngadi, Aznizam Abu Bakar, Zuliahani Ahmad, et al.

    Antibiotics and non-steroidal anti-inflammatory drugs (NSAIDs) are among the top pharmaceutical contaminants that have been often found in the aquatic environment. The presence of these contaminants in the aquatic environment is of great concern since it has a negative impact on both ecology and human health. In contrast to other tertiary treatments, adsorption stands out as a viable treatment approach since it provides benefits such as easier operating conditions with no byproduct formation. Commercial activated carbon is widely researched as a pharmaceutical adsorbent, but its large-scale applicability is constrained by its high cost. Agricultural waste also contains a large amount of various functional groups, which may be adapted to surface modification to increase its adsorption ability. In this regard, this study is designed to review the recent progress of efficient adsorbents derived from various agricultural wastes for the removal of antibiotics and NSAIDs contaminants from water bodies. Adsorbents made from agricultural waste have important benefits over commercial activated carbon for the reduction in waste while controlling water pollution.


  • Open Access

    Natural Polymeric Composites Derived from Animals, Plants, and Microbes for Vaccine Delivery and Adjuvant Applications: A Review

    by Abu Hassan Nordin, Siti Muhamad Nur Husna, Zuliahani Ahmad, Muhammad Luqman Nordin, Rushdan Ahmad Ilyas, Ahmad Khusairi Azemi, Noraznawati Ismail, Nordin Hawa Siti, Norzita Ngadi, Mohammad Saifulddin Mohd Azami, et al.

    A key element in ensuring successful immunization is the efficient delivery of vaccines. However, poor immunogenicity and adverse inflammatory immunogenic reactions make the establishment of an efficient vaccine delivery method a challenging task. The delivery of vaccines has been performed via a variety of delivery methods, including natural-polymer-based carriers that are relatively biocompatible and have low toxicity. The incorporation of adjuvants or antigens into biomaterial-based immunizations has demonstrated better immune response than formulations that just contain the antigen. This system may enable antigen-mediated immunogenicity and shelter and transport the cargo vaccine or antigen to the appropriate target organ. In this regard, this work reviews the recent applications of natural polymer composites from different sources, such as animals, plants, and microbes, in vaccine delivery systems.


  • Open Access

    The State of the Art of Natural Polymer Functionalized Fe3O4 Magnetic Nanoparticle Composites for Drug Delivery Applications: A Review

    by Abu Hassan Nordin, Zuliahani Ahmad, Siti Muhamad Nur Husna, Rushdan Ahmad Ilyas, Ahmad Khusairi Azemi, Noraznawati Ismail, Muhammad Luqman Nordin, Norzita Ngadi, Nordin Hawa Siti, Walid Nabgan, et al.

    Natural polymers have received a great deal of interest for their potential use in the encapsulation and transportation of pharmaceuticals and other bioactive compounds for disease treatment. In this perspective, the drug delivery systems (DDS) constructed by representative natural polymers from animals (gelatin and hyaluronic acid), plants (pectin and starch), and microbes (Xanthan gum and Dextran) are provided. In order to enhance the efficiency of polymers in DDS by delivering the medicine to the right location, reducing the medication’s adverse effects on neighboring organs or tissues, and controlling the medication’s release to stop the cycle of over- and under-dosing, the incorporation of Fe3O4 magnetic nanoparticles with the polymers has engaged the most consideration due to their rare characteristics, such as easy separation, superparamagnetism, and high surface area. This review is designed to report the recent progress of natural polymeric Fe3O4 magnetic nanoparticles in drug delivery applications, based on different polymers’ origins.


  • Open Access

    Electrical and Mechanical Properties of Silicone Electrical Conductive Adhesives (ECAs) Filled Carbon Black Treated with 3-Aminotriethoxysilane at Elevated Temperature

    by Nurul Hazirah Hasnol, Zuliahani Ahmad, UiTM Perlis, Muhamad Naiman Sarip, Ahmad Faiza Mohamad, UiTM Shah Alam, Ahmad Salihin Samsudin, Y.D Arief

    In this study, different formulation of silicone filled carbon black electric conducting adhesive (ECAs) were successfully fabricated. Carbon black (CB) was treated with 3-aminotriethoxysilane to improve the surface adhesion by grafting of amide functional groups on the surface of the CB. Various loading of untreated and treated CB (0%,5%,10% and 15%) on silicone ECAs using film casting method were prepared and characterized. The characterization was performed on the conductive adhesive film by using Fourier Transform Infrared Spectroscopy (FTIR), hardness and tensile testing. While for the electrical property, electrochemical impedance spectroscopy (EIS) was investigated. The FTIR spectrums confirmed the surface modification of CB with 3-aminotriethoxysilane and amide functional groups was presence at 1549 cm-1, 1250.7 cm-1, 1126.6 cm-1,976.16 cm-1and 860.02 cm-1corresponding to the N-H, SiO-H, Si-O-Si, C-N and C=C stretching vibrations of the amino groups (-R-NH3+) respectively. The conductivity of the ECAs was dependent on the CB loadings. As the CB loading increased, the conductivity of adhesive conductive film was increased up to 10% of CB loading and decreased when at 15% of CB loading. This is due to the gap distance of interparticle of silicone and CB is high. Whilst the tensile strength of the silicone filled CB increased with increasing of CB content both untreated and treated CB at 0.05954 MPa and 3.3027 MPa respectively. This is supported by hardness testing also showed the same trend with increment of CB loading, the hardness value also increased. The optimum value was found at 42 and 54 for untreated and treated CB respectively. The optimum formulation of electric conductivity was found at 10% loading of CB at 1.75E-08 /cm. The conductivity of ECAs filled CB at elevated temperature exhibits increment trend of untreated/treated CB at temperature of 100 °C to 160 °C however decreased at 180 °C. It is believed that with increasing the temperature, the interparticle average distance increase due to the difference in the thermal expansion of silicone and carbon black. The utilization of treated CB in silicone ECAs improved the conductivity and mechanical properties giving way to a full potential of using CB as filler.