Katja Holzer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Katja Holzer has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Christoph Hartmann
1 shared publicationF. Ettemeyer
Fraunhofer Research Institute for Casting, Composite and Processing Technology IGCV
1 shared publicationF. Füchsle
Technical University of Munich
1 shared publicationF. Steinlehner
Technical University of Munich
1 shared publication- Julika Hoyer
Technical University of Munich
1 shared publication Luisa Schottstedt
1 shared publication
Latest Publications
- Open Access
- 23 May 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
Experimental study on the influence of sheet temperature and punch speed during blanking of various sheet metal materials
This experimental study investigates the influence of sheet temperature and punch speed on blanking characteristics for aluminum alloy EN AW-5754, zinc and tin alloys, stainless steel 1.4301, press-hardened steel 22MnB5, and deep drawing grade DC06. Blanking experiments were conducted on a mechanical press. Circular blanks of 20 mm diameter with 5 % clearance were blanked with varied punch speed (0.1 m/s and 0.6–0.7 m/s depending on the sheet thickness) and varied initial sheet temperature (room-temperature, heated 50-80 °C, and cooled 0-(-30) °C). The maximum blanking force, blanking work, fracture shear stress, and the quality of the blanked edge were assessed. Experiments reveal that the sheet temperature has a strong effect on the blanking force. In the tested range, the punch speed primarily affects fracture initiation in steels, but has a negligible impact on non-ferrous alloys.
- 23 May 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
Open AccessExperimental study on the influence of sheet temperature and punch speed during blanking of various sheet metal materials
This experimental study investigates the influence of sheet temperature and punch speed on blanking characteristics for aluminum alloy EN AW-5754, zinc and tin alloys, stainless steel 1.4301, press-hardened steel 22MnB5, and deep drawing grade DC06. Blanking experiments were conducted on a mechanical press. Circular blanks of 20 mm diameter with 5 % clearance were blanked with varied punch speed (0.1 m/s and 0.6–0.7 m/s depending on the sheet thickness) and varied initial sheet temperature (room-temperature, heated 50-80 °C, and cooled 0-(-30) °C). The maximum blanking force, blanking work, fracture shear stress, and the quality of the blanked edge were assessed. Experiments reveal that the sheet temperature has a strong effect on the blanking force. In the tested range, the punch speed primarily affects fracture initiation in steels, but has a negligible impact on non-ferrous alloys.
- Open Access
Experimental Study on Deep-Drawing Dies Made of Pre-Stressed UHPC
Deep drawing is a cost-efficient way of producing sheet metal parts in high production volumes. Prototypes and very small series are expensive due to the cost of steel-forming tools. Ultra-high-performance concrete (UHPC) tools offer a cheap and fast alternative to conventional steel-forming tools. However, the flexural and tensile strength of UHPC limits its use in complex loading situations occurring in the forming die during deep drawing. To overcome this challenge, we propose pre-stressing UHPC by using expansive UHPC in a mechanically restrained condition. An aluminum powder-based expansive agent can be used to induce a free volume increase in UHPC specimens. With push-out test specimens, the increase in strength was tested when restraining the free volume increase with a steel reinforcement. After 3 and 12 months, no notable pre-straining effect could be measured when restraining the expansion of UHPC. Nonetheless, in deep-drawing experiments, the die made of expansive UHPC in a restrained condition withstood a maximal load during deep drawing of 110 kN. Compared to the die made from UHPC only, the failure mode changed from complete fracture to surface degradation of the drawing radius after 15 strokes.
Open AccessExperimental Study on Deep-Drawing Dies Made of Pre-Stressed UHPC
Deep drawing is a cost-efficient way of producing sheet metal parts in high production volumes. Prototypes and very small series are expensive due to the cost of steel-forming tools. Ultra-high-performance concrete (UHPC) tools offer a cheap and fast alternative to conventional steel-forming tools. However, the flexural and tensile strength of UHPC limits its use in complex loading situations occurring in the forming die during deep drawing. To overcome this challenge, we propose pre-stressing UHPC by using expansive UHPC in a mechanically restrained condition. An aluminum powder-based expansive agent can be used to induce a free volume increase in UHPC specimens. With push-out test specimens, the increase in strength was tested when restraining the free volume increase with a steel reinforcement. After 3 and 12 months, no notable pre-straining effect could be measured when restraining the expansion of UHPC. Nonetheless, in deep-drawing experiments, the die made of expansive UHPC in a restrained condition withstood a maximal load during deep drawing of 110 kN. Compared to the die made from UHPC only, the failure mode changed from complete fracture to surface degradation of the drawing radius after 15 strokes.
- 2 February 2023
- Published by Springer Nature
- p. 407-415
Potential of Ultra-High Performance Fiber Reinforced Concrete UHPFRC in Metal Forming Technology
- 2 February 2023
- Published by Springer Nature
- p. 407-415
Potential of Ultra-High Performance Fiber Reinforced Concrete UHPFRC in Metal Forming Technology