Julika Hoyer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Julika Hoyer has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Wolfram Volk
Technische Universität München
3 shared publications - Simon Kammerloher
Technical University of Munich
2 shared publications - Ahmet Zahid Demirezen
RWTH Aachen University
1 shared publication - Aron Ringel
Institute of Metal Forming (IBF), RWTH Aachen University, Intzestraße 10, 52072 Aachen, Germany
1 shared publication - David Bailly
Institute of Metal Forming (IBF), RWTH Aachen University, Aachen, Germany
1 shared publication - Junhe Lian
Aalto University
1 shared publication
Latest Publications
- Open Access
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 55-68
Influences of the Rolling Parameters on Multi-Material Copper-Aluminum Composites via Compound Casting
Multi-material components that consist of copper and aluminum enable the combination of advantageous mechanical, thermal, and electrical properties at competitive cost. While roll bonding is an efficient-solid state joining technique, its implementation requires fully processed, cold-rolled strip material from two process routes. Continuous compound casting in contrast offers a more efficient approach by combining aluminum and copper during casting, followed by flat rolling in a single process route. However, the differences in flow stress between the metals can cause non-uniform elongation and therefore significant shear stresses at the interface during rolling. These stresses may lead to a delamination of the compound if process conditions are not well controlled. This study investigates whether a geometrically structured interface, introduced during compound casting, can contribute to withstanding interfacial shear stresses through mechanical interlocking. In finite element simulations varying process parameters including height reduction, initial temperature, rolling speed ratio, and pass schedule were examined. Results show that a structured interface can effectively resist shear stresses at the copper-aluminum boundary, thereby improving joint stability during deformation. Furthermore, the strain distribution as well as the fluctuation of the shear stresses can be controlled by the process parameters. The findings indicate that the mechanical interlocking by a geometric interface combined with optimized process parameters can enhance the rolling of compound-cast copper-aluminum composites.
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 55-68
Open AccessInfluences of the Rolling Parameters on Multi-Material Copper-Aluminum Composites via Compound Casting
Multi-material components that consist of copper and aluminum enable the combination of advantageous mechanical, thermal, and electrical properties at competitive cost. While roll bonding is an efficient-solid state joining technique, its implementation requires fully processed, cold-rolled strip material from two process routes. Continuous compound casting in contrast offers a more efficient approach by combining aluminum and copper during casting, followed by flat rolling in a single process route. However, the differences in flow stress between the metals can cause non-uniform elongation and therefore significant shear stresses at the interface during rolling. These stresses may lead to a delamination of the compound if process conditions are not well controlled. This study investigates whether a geometrically structured interface, introduced during compound casting, can contribute to withstanding interfacial shear stresses through mechanical interlocking. In finite element simulations varying process parameters including height reduction, initial temperature, rolling speed ratio, and pass schedule were examined. Results show that a structured interface can effectively resist shear stresses at the copper-aluminum boundary, thereby improving joint stability during deformation. Furthermore, the strain distribution as well as the fluctuation of the shear stresses can be controlled by the process parameters. The findings indicate that the mechanical interlocking by a geometric interface combined with optimized process parameters can enhance the rolling of compound-cast copper-aluminum composites.
- 16 September 2025
- Published by Walter de Gruyter GmbH in Zeitschrift für wirtschaftlichen Fabrikbetrieb
- Vol. 120 (9) , 621-625
Modellierung und Validierung des Stranggießens von Aluminium und Kupfer
Beim Verbundstranggießen, bei dem zwei Metalle gegossen und im gleichen Schritt zu einem stoffschlüssigen Verbund gefügt werden, ist die Temperatur in der Verbundzone von entscheidender Bedeutung. Um Produktionsprozesse effizienter gestalten zu können, ist die Aufnahme von Sensordaten unerlässlich. Durch die eingesparten Fertigungsschritte können Taktzeiten sowie Energiekosten gesenkt werden. Temperaturen können im Stranggießwerkzeug gemessen, mit einem virtuellen Modell abgeglichen und dieses anhand der gemessenen Daten validiert werden. Dieser Beitrag soll zeigen, wie dieser Gießprozess aufgebaut und validiert werden kann.
- 16 September 2025
- Published by Walter de Gruyter GmbH in Zeitschrift für wirtschaftlichen Fabrikbetrieb
- Vol. 120 (9) , 621-625
Modellierung und Validierung des Stranggießens von Aluminium und Kupfer
Beim Verbundstranggießen, bei dem zwei Metalle gegossen und im gleichen Schritt zu einem stoffschlüssigen Verbund gefügt werden, ist die Temperatur in der Verbundzone von entscheidender Bedeutung. Um Produktionsprozesse effizienter gestalten zu können, ist die Aufnahme von Sensordaten unerlässlich. Durch die eingesparten Fertigungsschritte können Taktzeiten sowie Energiekosten gesenkt werden. Temperaturen können im Stranggießwerkzeug gemessen, mit einem virtuellen Modell abgeglichen und dieses anhand der gemessenen Daten validiert werden. Dieser Beitrag soll zeigen, wie dieser Gießprozess aufgebaut und validiert werden kann.
- Open Access
Experimental Study on Deep-Drawing Dies Made of Pre-Stressed UHPC
Deep drawing is a cost-efficient way of producing sheet metal parts in high production volumes. Prototypes and very small series are expensive due to the cost of steel-forming tools. Ultra-high-performance concrete (UHPC) tools offer a cheap and fast alternative to conventional steel-forming tools. However, the flexural and tensile strength of UHPC limits its use in complex loading situations occurring in the forming die during deep drawing. To overcome this challenge, we propose pre-stressing UHPC by using expansive UHPC in a mechanically restrained condition. An aluminum powder-based expansive agent can be used to induce a free volume increase in UHPC specimens. With push-out test specimens, the increase in strength was tested when restraining the free volume increase with a steel reinforcement. After 3 and 12 months, no notable pre-straining effect could be measured when restraining the expansion of UHPC. Nonetheless, in deep-drawing experiments, the die made of expansive UHPC in a restrained condition withstood a maximal load during deep drawing of 110 kN. Compared to the die made from UHPC only, the failure mode changed from complete fracture to surface degradation of the drawing radius after 15 strokes.
Open AccessExperimental Study on Deep-Drawing Dies Made of Pre-Stressed UHPC
Deep drawing is a cost-efficient way of producing sheet metal parts in high production volumes. Prototypes and very small series are expensive due to the cost of steel-forming tools. Ultra-high-performance concrete (UHPC) tools offer a cheap and fast alternative to conventional steel-forming tools. However, the flexural and tensile strength of UHPC limits its use in complex loading situations occurring in the forming die during deep drawing. To overcome this challenge, we propose pre-stressing UHPC by using expansive UHPC in a mechanically restrained condition. An aluminum powder-based expansive agent can be used to induce a free volume increase in UHPC specimens. With push-out test specimens, the increase in strength was tested when restraining the free volume increase with a steel reinforcement. After 3 and 12 months, no notable pre-straining effect could be measured when restraining the expansion of UHPC. Nonetheless, in deep-drawing experiments, the die made of expansive UHPC in a restrained condition withstood a maximal load during deep drawing of 110 kN. Compared to the die made from UHPC only, the failure mode changed from complete fracture to surface degradation of the drawing radius after 15 strokes.
- Open Access
A Method for Characterising the Influence of Casting Parameters on the Metallurgical Bonding of Copper and Steel Bimetals
Traditional casting technology offers two mayor drawbacks towards research activities. On the one hand, time and resources needed for every casting are rather high. The mould has to be able to withstand the high temperatures introduced by the melt and provide cooling for the cast part. Preparation and installation of measuring equipment therefore takes time. Additionally, due to the high mass of the mould when compared to the cast part, parameter variations are rather limited in their resulting effect on the temperature-time profile being one of the most prominent factors regarding cast quality. Especially when pouring by hand, variations in casting times and rates superimpose effects created intentionally. Therefore, a different process was advanced and evaluated, allowing to minimise some of the drawbacks mentioned before. The key idea is to drastically reduce casting size to the dimensions of one specimen and to apply a highly automated production route. As such, a mirror furnace was modified as to allow the processing of melt. Due to the specimens size, an adaption of mechanical testing equipment was performed and evaluated. As an example, copper-iron bimetal specimens were examined by light microscopy, micro hardness testing, nanoindentation as well as tensile and torsion testing. As the results were consistent, the newly introduced method can be applied successfully in casting research. This allows for highly reproducible results, reducing the uncertainty of temperature measurements of a specimen due to the distance between them. The possibility of separating influencing variables like maximum temperature and cooling rate allows an analysis of the casting process, which would require different moulds to do so in traditional casting methods. The next steps will be directed at a broader variety of metals processed and at a direct comparison between the new process route and traditional casting technology.
Open AccessA Method for Characterising the Influence of Casting Parameters on the Metallurgical Bonding of Copper and Steel Bimetals
Traditional casting technology offers two mayor drawbacks towards research activities. On the one hand, time and resources needed for every casting are rather high. The mould has to be able to withstand the high temperatures introduced by the melt and provide cooling for the cast part. Preparation and installation of measuring equipment therefore takes time. Additionally, due to the high mass of the mould when compared to the cast part, parameter variations are rather limited in their resulting effect on the temperature-time profile being one of the most prominent factors regarding cast quality. Especially when pouring by hand, variations in casting times and rates superimpose effects created intentionally. Therefore, a different process was advanced and evaluated, allowing to minimise some of the drawbacks mentioned before. The key idea is to drastically reduce casting size to the dimensions of one specimen and to apply a highly automated production route. As such, a mirror furnace was modified as to allow the processing of melt. Due to the specimens size, an adaption of mechanical testing equipment was performed and evaluated. As an example, copper-iron bimetal specimens were examined by light microscopy, micro hardness testing, nanoindentation as well as tensile and torsion testing. As the results were consistent, the newly introduced method can be applied successfully in casting research. This allows for highly reproducible results, reducing the uncertainty of temperature measurements of a specimen due to the distance between them. The possibility of separating influencing variables like maximum temperature and cooling rate allows an analysis of the casting process, which would require different moulds to do so in traditional casting methods. The next steps will be directed at a broader variety of metals processed and at a direct comparison between the new process route and traditional casting technology.