Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dario Guarda has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Corrigendum to “New liquid fraction measurement methodology for phase change material analysis based on X-ray computed tomography” [Int. J. Therm. Sci. 194 (2023) 108585]

    by Dario Guarda, Jorge Martinez-Garcia, Benjamin Fenk, David Schiffmann, Damian Gwerder, Anastasia Stamatiou, Jörg Worlitschek, Simone Mancin, Philipp Schuetz

  • Open Access

    Experimental assessment of the impact of PCM Type and Heat Exchanger Geometry on a Real-Scale Latent Thermal Energy Storage

    by Dario Guarda, Claudio Zilio, Simone Mancin, Giulia Righetti

    Latent thermal energy storage (LTES) systems based on phase change materials (PCMs) are increasingly investigated for residential heat pump applications, often focusing on total stored energy and average thermal power. However, these metrics alone do not fully describe the effective usability of the stored energy under realistic operating conditions. This work experimentally investigates the thermal field evolution and usable energy quality of a real-scale PCM-based LTES, with particular emphasis on temperature distribution, stratification, and energy exploitability. A 0.1 m³ insulated storage unit equipped with a finned-coil heat exchanger was tested using two PCMs with similar phase change temperature (around 48 °C) —an organic and an inorganic PCM—and two heat exchanger geometries featuring different tube coverage. Charging and discharging experiments were carried out under controlled boundary conditions representative of residential heat pump operation. The internal thermal field was resolved using a dense array of thermocouples distributed throughout the storage volume. Results show that PCM type significantly affects thermal diffusion and stratification: the hydrated salt exhibits lower internal temperature gradients and a higher fraction of usable energy during discharge, while the organic enables faster cycling but with more pronounced thermal non-uniformities. Increasing the heat exchanger surface area improves temperature homogeneity and reduces stratification, regardless of the PCM. The study demonstrates that thermal field analysis provides critical design information beyond conventional energy metrics, supporting industrial-oriented design and system integration of PCM-based LTES units.

  • Open Access

    Numerical Study of a Single Dwelling with Latent Thermal Energy Storage for Low Grid Dependence for Space Cooling

    by Gianluca Slaviero, Carolina Mira-Hernández, Dario Guarda, Giuseppe Travaglini, Andrea Dolfi, Claudio Zilio, Simone Mancin

    In 2019, approximately 37 Gton of CO2 were released into the atmosphere, highlighting the urgent need for innovative energy solutions. Space heating and cooling account for significant energy consumption, with cooling demand in Europe expected to exceed 100 TWh annually. Latent thermal energy storage (LTES) offers a promising approach to optimize energy management and increase renewable energy utilization for heating and cooling demands. This study evaluates a novel 18 kWh LTES using roll-bond technology and bio-based phase change material with phase transition at 11°C meant for space cooling. A numerical model in TRNSYS assesses its impact on a 102 m2 dwelling in three locations, Venice, Kuala Lumpur, and Brisbane, analyzing energy savings, A/C system interactions and thermal comfort improvements. Results show that the integration of a 5 kWp photovoltaic array reduced grid electricity consumption for cooling by 50–64% across the three locations, while the addition of the 18 kWh LTES enabled night cooling and further decreased grid dependence by 91% in Kuala Lumpur and Brisbane, and 89% in Venice. The levelized cost of cooling was reduced by up to 45%, and CO2 emissions decreased by nearly 90%, confirming the techno-economic feasibility of the proposed system for residential applications.

  • Open Access

    Experimental Assessment of Material and Geometry Effects in a Medium-Temperature PCM-Based Latent Thermal Energy Storage for Residential Heat Pumps

    by Dario Guarda, Claudio Zilio, Simone Mancin, Giulia Righetti

    This study presents a comprehensive experimental evaluation of medium-temperature latent thermal energy storage systems designed for integration with residential heat pumps powered by renewable energy. Despite significant research on phase change materials, direct comparisons between inorganic and organic PCMs under identical geometries and real-scale operating conditions remain limited, particularly for systems operating in the 45–50 °C range. To address this gap, two finned-coil heat exchanger geometries and two phase change materials—an organic material and a hydrated salt—were tested in a 0.1 m³ storage unit under controlled operating conditions. Charging and discharging cycles were performed across three flow rates and three temperature levels. Results show that the hydrated salt provides 40–50% higher energy density and a 22% higher heat transfer rate, whereas increasing the heat transfer area reduces charging time by around 20%. A scale analysis confirms that conduction within the phase change material dominates the process. An exponential energy-prediction model was developed to estimate stored and released energy as a function of time, inlet temperature difference, and flow rate. The calibrated equation reproduces system dynamics with mean square error values of 0.10–0.39 kWh, enabling fast performance estimation without full experimental characterization. These findings deliver actionable design guidelines for compact and efficient latent thermal energy storage solutions in heat-pump-based residential systems.

  • Open Access

    Applications of X-Ray Computed Tomography Technology to Solid–Liquid Phase Change Materials—A Review

    by Jorge Martinez-Garcia, Dario Guarda, Damian Gwerder, Benjamin Fenk, Rebecca Ravotti, Simone Mancin, Anastasia Stamatiou, Jörg Worlitschek, Ludger Josef Fischer, Philipp Schuetz

    Latent heat thermal energy storage (LHTES) based on phase change materials (PCMs) is receiving increasing interest since it offers high energy storage density while enabling the integration of variable renewable energies, hence boosting the transition towards a climate-neutral future. Despite the advantages that PCMs offer in providing a nearly isothermal solid–liquid phase transition, they still face some challenges that limit their deployment in real applications such as low thermal conductivity, phase separation, and supercooling, which affect charging and discharging rates. X-ray computed tomography (XCT) is a non-destructive imaging technique widely used in materials science for both qualitative and quantitative analysis of material microstructures and their evolution. Recent advances in laboratory-XCT instrumentation enabled short acquisition times on the order of tens of seconds which allows the investigation of dynamic processes in situ by time-lapse XCT measurements. These advances open new opportunities for revealing information on the morphology of solid–liquid PCMs. Despite the fact that XCT imaging has significant potential for energy research, its application in the field of PCMs is fairly new. A key enabler of applications of XCT to PCMs is the density difference between solid and liquid PCMs, which was found to be higher than 7% for all investigated PCMs. This enabled solid and liquid phases to be distinguished one from the other and properly quantified over time. The present work reviews the principles of laboratory-based XCT and the recent applications of XCT technology in the characterisation of PCMs, with emphasis on the study of the solid–liquid phase transition and validation of numerical PCM models by addressing the potentialities and challenges of XCT in PCM research.


  • Open Access

    Applications of Computed Tomography (CT) Technology to Solid-Liquid Phase Change Materials—A Review

    by Jorge Martinez-Garcia, Dario Guarda, Damian Gwerder, Benjamin Fenk, Rebecca Ravotti, Simone Mancin, Anastasia Stamatiou, Jörg Worlitschek, Ludger Josef Fischer, Philipp Schuetz

    Latent Heat Thermal Energy Storage (LHTES) based on phase change materials (PCM) is receiving increasing interest, since it offers high energy storage density while enabling the integration of variable renewable energies, hence boosting the transition towards a climate-neutral future. Despite the advantages that PCMs offer in providing a nearly isothermal solid–liquid phase transition, they still face some challenges that limit their deployment in real applications such as, low thermal conductivity, phase separation and supercooling, which affect charging and discharging rates. X-ray computed tomography (XCT) is a non-destructive imaging technique widely used in materials science for both qualitative and quantitative analysis of material microstructures and their evolution. Recent advances in laboratory-XCT instrumentation enabled short acquisition times on the order of tens of seconds which enable the investigation of dynamic processes in-situ by time-lapse XCT measurements. These advances open new opportunities for revealing information on the solid-liquid PCMs. Despite XCT imaging has significant potential for energy research, its application in the field of PCMs is fairly new. The present work reviews the principles of laboratory-based XCT and the recent applications of XCT technology in the characterisation of PCMs, with emphasis on the study of the solid-liquid phase transition and validation of numerical PCM models.


  • Open Access

    A Comparative Experimental Analysis of a Cold Latent Thermal Storage System Coupled with a Heat Pump/Air Conditioning Unit

    by Claudio Zilio, Giulia Righetti, Dario Guarda, Francesca Martelletto, Simone Mancin

    The decarbonization of residential cooling systems requires innovative solutions to overcome the mismatch between the renewable energy availability and demand. Integrating latent thermal energy storage (LTES) with heat pump/air conditioning (HP/AC) units can help balance energy use and enhance efficiency. However, the dynamic behavior of such integrated systems, particularly under low-load conditions, remains underexplored. This study investigates a 5 kW HP/AC unit coupled with an 18 kWh LTES system using a bio-based Phase Change Material (PCM) with a melting temperature of 9 °C. Two configurations were tested: charging the LTES using either a thermostatic bath or the HP/AC unit. Key parameters such as the stored energy, temperature distribution, and cooling capacity were analyzed. The results show that, under identical conditions (2 °C inlet temperature, 16 L/min flow rate), the energy stored using the HP/AC unit was only 6.3% lower than with the thermostatic bath. Nevertheless, significant cooling capacity fluctuations occurred with the HP/AC unit due to compressor modulation and anti-frost cycles. The compressor frequency varied from 75 Hz to 25 Hz, and inefficient on-off cycling appeared in the final phase, when the power demand dropped below 1 kW. These findings highlight the importance of integrated system design and control strategies. A co-optimized HP/AC–LTES setup is essential to avoid performance degradation and to fully exploit the benefits of thermal storage in residential cooling.


  • Open Access

    X-ray computed tomography analysis of calcium chloride hexahydrate solidification

    by Dario Guarda, Jorge Martinez-Garcia, Benjamin Fenk, Poppy O’NEill, Rebecca Ravotti, Damian Gwerder, Anastasia Stamatiou, Jörg Worlitschek, Simone Mancin, Philipp Schuetz


  • New liquid fraction measurement methodology for phase change material analysis based on X-ray computed tomography

    by Dario Guarda, Jorge Martinez-Garcia, Benjamin Fenk, David Schiffmann, Damian Gwerder, Anastasia Stamatiou, Jörg Worlitschek, Simone Mancin, Philipp Schuetz