Zhiqiang Li
Research Subjects
Zhiqiang Li has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Yongli Ji
China Research Institute of Radiowave Propagation, Xinxiang, Henan, China
3 shared publications - Defu Zang
SINOPEC MATRIX Corp 1 , GEO-MWD/LWD & Logging Research Institute, Qingdao, China.;;
2 shared publications Jigen Xia
China Research Institute of Radiowave Propagation, Xinxiang, Henan, China
2 shared publications- Jigen Xia
China Research Institute of Radiowave Propagation, Xinxiang 453000, China
2 shared publications - Lei Wang
State Key Laboratory of Deep Oil and Gas and the School of Geosciences, China University of Petroleum (East China), Qingdao, China
2 shared publications - Shaogui Deng
China University of Petroleum (East China) 1 , State Key Laboratory of Deep Oil and Gas, Qingdao, China and , School of Geosciences, Qingdao, China
2 shared publications
Latest Publications
- Open Access
- 24 February 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (5) , 407
Time-Domain Electromagnetic Instrument for Onshore and Offshore Petroleum Resource Prospecting
Currently, marine and land oil resources have entered the high-water extraction stage. The remaining oil is dispersed, and the oil–water relationship is complex, making it increasingly difficult to extract. However, traditional electrical logging techniques are limited by the shielding effect of highly conductive steel casing, rendering them unsuitable for formation resistivity measurement in casing wells. Time-domain electromagnetic method overcomes the constraints of downhole push-off systems and casing conditions, enabling continuous measurement and acquisition of formation resistivity parameters. To overcome these limitations, this paper proposes an active compensation method based on differential measurements between specially configured coils, enabling the early response of the formation to be identified, the method enhances weak signal detection capabilities in casing formations. The coils offset part of the casing influence, while the casing background serves as baseline information. A time-domain electromagnetic instrument for metal casing resistivity measurement was developed, along with a ground water tank resistivity calibration device. The experimental results show that the instrument can effectively suppress casing response, obtain formation resistivity signals, and provide effective guidance methods for measuring formation resistivity of casing wells in the ocean and land.
- 24 February 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (5) , 407
Open AccessTime-Domain Electromagnetic Instrument for Onshore and Offshore Petroleum Resource Prospecting
Currently, marine and land oil resources have entered the high-water extraction stage. The remaining oil is dispersed, and the oil–water relationship is complex, making it increasingly difficult to extract. However, traditional electrical logging techniques are limited by the shielding effect of highly conductive steel casing, rendering them unsuitable for formation resistivity measurement in casing wells. Time-domain electromagnetic method overcomes the constraints of downhole push-off systems and casing conditions, enabling continuous measurement and acquisition of formation resistivity parameters. To overcome these limitations, this paper proposes an active compensation method based on differential measurements between specially configured coils, enabling the early response of the formation to be identified, the method enhances weak signal detection capabilities in casing formations. The coils offset part of the casing influence, while the casing background serves as baseline information. A time-domain electromagnetic instrument for metal casing resistivity measurement was developed, along with a ground water tank resistivity calibration device. The experimental results show that the instrument can effectively suppress casing response, obtain formation resistivity signals, and provide effective guidance methods for measuring formation resistivity of casing wells in the ocean and land.
- 19 December 2024
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 90 (1) , D11-D25
The joint physics and data-driven geometrical factor of array laterolog in layered formations
Numerical geometrical factors (GFs) are developed for array laterolog measurements in 1D cylindrically and planarly layered formations. The kernel of GFs assumes that laterolog responses can be expressed in terms of the linear superposition of formation resistivities at different units. Two techniques, namely physics-driven modeling and data-driven approximation, have been used to ensure the computational accuracy and efficiency of GFs. Physics-driven modeling uses a 3D finite-element algorithm to generate high-precision and fully labeled GF data and library. Subsequently, these predetermined data are trained offline using classical neural network algorithms to establish an implicit relationship between the formation parameters and GFs. The joint physics and data-driven GFs present three main advantages. First, they enable the direct representation of the spatial sensitivity of layered formations laterally and horizontally in vertical and horizontal wells. Second, GFs can be used to calculate the array laterolog responses rapidly. The computation speed can be enhanced thousands of times in comparison with traditional physic-driven modeling, allowing for real-time data processing. Another noteworthy aspect is that GF forward modeling can handle formations with arbitrary layers, thereby resolving the fixed-layer modeling issue inherent in traditional data-driven methods. Third, the GFs can be used to approximate the derivative of the logging response with respect to formation resistivity, significantly reducing the complexity of the Jacobian matrix calculation for deterministic inversion. These numerical GFs not only serve as an excellent alternative simulator for the array laterolog but will also be helpful to accelerate the modeling and inversion of other logging measurements in layered structures.
- 19 December 2024
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 90 (1) , D11-D25
The joint physics and data-driven geometrical factor of array laterolog in layered formations
Numerical geometrical factors (GFs) are developed for array laterolog measurements in 1D cylindrically and planarly layered formations. The kernel of GFs assumes that laterolog responses can be expressed in terms of the linear superposition of formation resistivities at different units. Two techniques, namely physics-driven modeling and data-driven approximation, have been used to ensure the computational accuracy and efficiency of GFs. Physics-driven modeling uses a 3D finite-element algorithm to generate high-precision and fully labeled GF data and library. Subsequently, these predetermined data are trained offline using classical neural network algorithms to establish an implicit relationship between the formation parameters and GFs. The joint physics and data-driven GFs present three main advantages. First, they enable the direct representation of the spatial sensitivity of layered formations laterally and horizontally in vertical and horizontal wells. Second, GFs can be used to calculate the array laterolog responses rapidly. The computation speed can be enhanced thousands of times in comparison with traditional physic-driven modeling, allowing for real-time data processing. Another noteworthy aspect is that GF forward modeling can handle formations with arbitrary layers, thereby resolving the fixed-layer modeling issue inherent in traditional data-driven methods. Third, the GFs can be used to approximate the derivative of the logging response with respect to formation resistivity, significantly reducing the complexity of the Jacobian matrix calculation for deterministic inversion. These numerical GFs not only serve as an excellent alternative simulator for the array laterolog but will also be helpful to accelerate the modeling and inversion of other logging measurements in layered structures.
- Open Access
- 29 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (15) , 6619
Calculation of Lateral Logging Response and Environmental Impact Factor Analysis for Small Borehole Array
This paper refines an optimized array lateral logging tool designed for small boreholes, leveraging existing technologies. The tool features four investigation depth curves, and resistivity response curves are derived through finite element model simulations considering variables such as borehole size, mud characteristics, invasion zone features, resistive annuli, formation rock properties, and formation resistivity anisotropy. The findings included the following: (1) Increasing the wellbore diameter uniformly decreased resistivity across all four investigation depths, positively correlating with borehole size. When mud resistivity (Rm) exceeded formation resistivity (Rt), resistivity curves became distorted. (2) For high- and low-invasion models, the ratio of the deepest to the shallowest investigation depth curves ranged from 1 to 8 and 0.6 to 0.9, respectively, with maximum separation at an invasion depth of 0.5–0.8 m. (3) Under invasion conditions with annuli, an invasion zone depth and annulus width around 0.4 m yield well separated the resistivity curves for all depths. Low- and high-resistivity annuli of 2 m and 0.7 m, respectively, can cause curve intersections. (4) When the formation thickness exceeded 0.2 m, the tool accurately reflected formation resistivity variations and demonstrated effective layer identification in multi-layer conditions. (5) In anisotropic formations, resistivity was negatively correlated with the anisotropy coefficient (λ) as it changed from 2 to 4. The instrument can be fully utilized in the exploration of thin interlayers in oil and gas, significantly enhancing the accuracy of resource identification and extraction technologies.
- 29 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (15) , 6619
Open AccessCalculation of Lateral Logging Response and Environmental Impact Factor Analysis for Small Borehole Array
This paper refines an optimized array lateral logging tool designed for small boreholes, leveraging existing technologies. The tool features four investigation depth curves, and resistivity response curves are derived through finite element model simulations considering variables such as borehole size, mud characteristics, invasion zone features, resistive annuli, formation rock properties, and formation resistivity anisotropy. The findings included the following: (1) Increasing the wellbore diameter uniformly decreased resistivity across all four investigation depths, positively correlating with borehole size. When mud resistivity (Rm) exceeded formation resistivity (Rt), resistivity curves became distorted. (2) For high- and low-invasion models, the ratio of the deepest to the shallowest investigation depth curves ranged from 1 to 8 and 0.6 to 0.9, respectively, with maximum separation at an invasion depth of 0.5–0.8 m. (3) Under invasion conditions with annuli, an invasion zone depth and annulus width around 0.4 m yield well separated the resistivity curves for all depths. Low- and high-resistivity annuli of 2 m and 0.7 m, respectively, can cause curve intersections. (4) When the formation thickness exceeded 0.2 m, the tool accurately reflected formation resistivity variations and demonstrated effective layer identification in multi-layer conditions. (5) In anisotropic formations, resistivity was negatively correlated with the anisotropy coefficient (λ) as it changed from 2 to 4. The instrument can be fully utilized in the exploration of thin interlayers in oil and gas, significantly enhancing the accuracy of resource identification and extraction technologies.
- Open Access
- 11 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (14) , 6060
Theoretical Transmission Model of Helical Loop Antenna in Cased Wells and Channel Characteristics Analysis
In the environment of oil and gas wells, the shielding effect of metal casing increases the difficulty of applying wireless electromagnetic wave transmission technology in such wells. This paper constructs a theoretical model of downhole electromagnetic helical loop transmission based on the finite element method. The magnetic loop is equated with the helical loop antenna in the model. By means of simulation calculations, this study deeply investigates the impact of various factors, such as working frequency within the cased well, drilling fluid resistivity, formation resistivity, drill string dimensions, and electrical conductivity, on the attenuation pattern of the helical loop antenna. The results show that low-frequency signals experience relatively less attenuation underground, while high-frequency signals demonstrate better transmission effects over shorter distances. Moreover, drilling fluids with low resistivity are more suitable for short-distance transmission, whereas high resistivity can effectively reduce signal attenuation and improve transmission distance. The variation in formation resistivity has a relatively small impact on signal transmission and can be considered negligible. In terms of drill string characteristics, as the electrical conductivity of the drill collars increases, signal attenuation gradually decreases, and the amplitude of the received signal is enhanced. With the inner and outer diameters of the drill collars remaining the same, a finer inner diameter of the casing aids electromagnetic wave short-distance transmission, whereas a thicker casing can reduce electromagnetic wave attenuation. Theoretical and practical results are in good agreement through field trial comparative analysis.
- 11 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (14) , 6060
Open AccessTheoretical Transmission Model of Helical Loop Antenna in Cased Wells and Channel Characteristics Analysis
In the environment of oil and gas wells, the shielding effect of metal casing increases the difficulty of applying wireless electromagnetic wave transmission technology in such wells. This paper constructs a theoretical model of downhole electromagnetic helical loop transmission based on the finite element method. The magnetic loop is equated with the helical loop antenna in the model. By means of simulation calculations, this study deeply investigates the impact of various factors, such as working frequency within the cased well, drilling fluid resistivity, formation resistivity, drill string dimensions, and electrical conductivity, on the attenuation pattern of the helical loop antenna. The results show that low-frequency signals experience relatively less attenuation underground, while high-frequency signals demonstrate better transmission effects over shorter distances. Moreover, drilling fluids with low resistivity are more suitable for short-distance transmission, whereas high resistivity can effectively reduce signal attenuation and improve transmission distance. The variation in formation resistivity has a relatively small impact on signal transmission and can be considered negligible. In terms of drill string characteristics, as the electrical conductivity of the drill collars increases, signal attenuation gradually decreases, and the amplitude of the received signal is enhanced. With the inner and outer diameters of the drill collars remaining the same, a finer inner diameter of the casing aids electromagnetic wave short-distance transmission, whereas a thicker casing can reduce electromagnetic wave attenuation. Theoretical and practical results are in good agreement through field trial comparative analysis.
- Open Access
- 17 April 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (4) , e0302032
A standard calibration method based on a symmetric resistance network matrix for galvanic logging instruments
An increasing number of measurement electrodes have been designed to satisfy the demand for high-resolution detection using galvanic logging technology in complex formations. The forward modeling response analysis of logging tools has important guiding significance in the design of galvanic logging tools. Based on a three-dimensional finite element numerical simulation method, we established a forward model of galvanic multi-electrodes in a complex formation. We also designed a symmetrical resistance network model of the formation with equivalent resistance between two electrodes. A symmetrical resistance network was derived using the balanced bridge method. The asymmetrical admittance matrix was extended to a symmetrical extended admittance matrix to realize a convenient calculation of the equivalent symmetrical resistance network in complex formations. Verification of the microcolumn-focused logging tool, with nine electrodes in a simulated standard well, and an evaluation of the degree of invasion in an actual oil well indicate that this calibration method can improve the measurement accuracy of galvanic logging instruments.
- 17 April 2024
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 19 (4) , e0302032
Open AccessA standard calibration method based on a symmetric resistance network matrix for galvanic logging instruments
An increasing number of measurement electrodes have been designed to satisfy the demand for high-resolution detection using galvanic logging technology in complex formations. The forward modeling response analysis of logging tools has important guiding significance in the design of galvanic logging tools. Based on a three-dimensional finite element numerical simulation method, we established a forward model of galvanic multi-electrodes in a complex formation. We also designed a symmetrical resistance network model of the formation with equivalent resistance between two electrodes. A symmetrical resistance network was derived using the balanced bridge method. The asymmetrical admittance matrix was extended to a symmetrical extended admittance matrix to realize a convenient calculation of the equivalent symmetrical resistance network in complex formations. Verification of the microcolumn-focused logging tool, with nine electrodes in a simulated standard well, and an evaluation of the degree of invasion in an actual oil well indicate that this calibration method can improve the measurement accuracy of galvanic logging instruments.
- 7 January 2024
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 89 (4) , D243-D254
Research on high-power and high-efficiency emission of crosswell electromagnetic logging
Crosswell electromagnetic (EM) logging has useful applications in oil, gas, and water monitoring as well as carbon sequestration estimation. Difficulties in the efficient propagation of EM waves through a steel casing inhibit crosswell EM logging at distances greater than 300 m. This study investigates whether high-power transmission and high-efficiency transmitting antennas can resolve the challenges of long-distance crosswell EM logging through steel casings. Theoretical analysis indicates that the emission moment should be at least 12,000 A·m2. By calculating the equivalent relative permeability and selecting the appropriate coil materials and magnetic cores, the maximum emission magnetic moment can create a high-power transmission. Based on series and parallel resonant circuits and the alternating current/direct current cable core multiplexing power supply method, the effective transmission bandwidth is broadened and the transmission efficiency increases by three times. The emission unit is fabricated and tested using single, double, and fiberglass casing. We observe that the crosswell EM technology performs better for nonmetal casing wells than that for metal casing wells. The amplitude and phase curves between two fiberglass casing wells in the range of 425 m are quite smooth. However, the receiving signals in the double-layer steel casing decrease to only a few tenths of the value in the fiberglass casing wells, highlighting the difficulty of long-distance EM wave transmission when using steel casings. Thus, studies on EM transmission through four or more layers of steel casings should be conducted in the future.
- 7 January 2024
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 89 (4) , D243-D254
Research on high-power and high-efficiency emission of crosswell electromagnetic logging
Crosswell electromagnetic (EM) logging has useful applications in oil, gas, and water monitoring as well as carbon sequestration estimation. Difficulties in the efficient propagation of EM waves through a steel casing inhibit crosswell EM logging at distances greater than 300 m. This study investigates whether high-power transmission and high-efficiency transmitting antennas can resolve the challenges of long-distance crosswell EM logging through steel casings. Theoretical analysis indicates that the emission moment should be at least 12,000 A·m2. By calculating the equivalent relative permeability and selecting the appropriate coil materials and magnetic cores, the maximum emission magnetic moment can create a high-power transmission. Based on series and parallel resonant circuits and the alternating current/direct current cable core multiplexing power supply method, the effective transmission bandwidth is broadened and the transmission efficiency increases by three times. The emission unit is fabricated and tested using single, double, and fiberglass casing. We observe that the crosswell EM technology performs better for nonmetal casing wells than that for metal casing wells. The amplitude and phase curves between two fiberglass casing wells in the range of 425 m are quite smooth. However, the receiving signals in the double-layer steel casing decrease to only a few tenths of the value in the fiberglass casing wells, highlighting the difficulty of long-distance EM wave transmission when using steel casings. Thus, studies on EM transmission through four or more layers of steel casings should be conducted in the future.
- Open Access
Identification of Underground Artificial Cavities Based on the Bayesian Convolutional Neural Network
The development of underground artificial cavities plays an important role in the exploitation of urban spatial resources. As the rapidly growing number of underground artificial cavities with different depths and scales increases, the detection and identification of underground artificial cavities has become a key issue in underground engineering studies. Geophysical techniques have been widely used for the construction, management, and maintenance of underground artificial cavities. In this study, we present two identification methods for underground artificial cavities. Apparent resistivity imaging is the most popular technique for quickly identifying underground artificial cavities, using the forward simulation results of a three-dimensional earth model and comparing these with the preset positions of artificial cavities, as demonstrated in the experiment. To further improve the efficiency of underground artificial cavity identification, we developed a fast recognition approach for underground artificial cavities based on the Bayesian convolutional neural network (BCNN). Compared to a traditional convolutional neural network, the performance of the BCNN method was greatly improved in terms of the classification accuracy and efficiency of identifying underground artificial cavities with apparent resistivity image datasets.
Open AccessIdentification of Underground Artificial Cavities Based on the Bayesian Convolutional Neural Network
The development of underground artificial cavities plays an important role in the exploitation of urban spatial resources. As the rapidly growing number of underground artificial cavities with different depths and scales increases, the detection and identification of underground artificial cavities has become a key issue in underground engineering studies. Geophysical techniques have been widely used for the construction, management, and maintenance of underground artificial cavities. In this study, we present two identification methods for underground artificial cavities. Apparent resistivity imaging is the most popular technique for quickly identifying underground artificial cavities, using the forward simulation results of a three-dimensional earth model and comparing these with the preset positions of artificial cavities, as demonstrated in the experiment. To further improve the efficiency of underground artificial cavity identification, we developed a fast recognition approach for underground artificial cavities based on the Bayesian convolutional neural network (BCNN). Compared to a traditional convolutional neural network, the performance of the BCNN method was greatly improved in terms of the classification accuracy and efficiency of identifying underground artificial cavities with apparent resistivity image datasets.
- Open Access
- 20 February 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 11
Research and application of high-resolution micro-cylindrically focused logging tool
The unknown nature and complexity of non-uniform formations cause new difficulties and challenges to the accurate detection of electrical instruments in shallow formations. The micro-cylindrically focused logging tool (MCFL) can provide three original measurement curves, RB0, RB1, and RB2, with different detection depths, which reflect the flushing zone resistivity, mudcake resistivity, and mudcake thickness. In this study, the finite element method was used to model and analyze the micro-cylindrically focused logging tool tool in a three-dimensional non-uniform medium model. By converting the partial differential equation into a generalized polar problem, the logging response characteristics of the micro-cylindrically focused logging tool tool at different detection depths and ranges, mudcake thicknesses, flush zones, and mudcake resistivity contrasts were investigated. Inverse processing of the micro-cylindrically focused logging tool data using the least-squares method was used to obtain the flush zone resistivity, mudcake resistivity, and mudcake thickness, based on which the micropotential and microgradient curves were synthesized. In addition, a digital focusing method was proposed to improve the focusing accuracy and flexibility of the instrument, enhancing the performance of the micro-cylindrically focused logging tool. The optimized design of the focusing method significantly improved the detection performance of the pole plate. This plays an important role in the evaluation of thin layers and oil-water reservoirs.
- 20 February 2023
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 11
Open AccessResearch and application of high-resolution micro-cylindrically focused logging tool
The unknown nature and complexity of non-uniform formations cause new difficulties and challenges to the accurate detection of electrical instruments in shallow formations. The micro-cylindrically focused logging tool (MCFL) can provide three original measurement curves, RB0, RB1, and RB2, with different detection depths, which reflect the flushing zone resistivity, mudcake resistivity, and mudcake thickness. In this study, the finite element method was used to model and analyze the micro-cylindrically focused logging tool tool in a three-dimensional non-uniform medium model. By converting the partial differential equation into a generalized polar problem, the logging response characteristics of the micro-cylindrically focused logging tool tool at different detection depths and ranges, mudcake thicknesses, flush zones, and mudcake resistivity contrasts were investigated. Inverse processing of the micro-cylindrically focused logging tool data using the least-squares method was used to obtain the flush zone resistivity, mudcake resistivity, and mudcake thickness, based on which the micropotential and microgradient curves were synthesized. In addition, a digital focusing method was proposed to improve the focusing accuracy and flexibility of the instrument, enhancing the performance of the micro-cylindrically focused logging tool. The optimized design of the focusing method significantly improved the detection performance of the pole plate. This plays an important role in the evaluation of thin layers and oil-water reservoirs.
- 11 December 2022
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 88 (2) , D115-D129
A new semianalytical algorithm for rapid simulation of triaxial electromagnetic logging responses in multilayered biaxial anisotropic formations
A set of compact and stable formulas are developed for the computation of triaxial electromagnetic (EM) logging responses in multilayered formations with biaxial anisotropy. These formulas are based on a new global amplitude propagator matrix (GAPM) algorithm, which derives the amplitudes of upgoing/downgoing waves at the boundaries rather than the reflection/transmission coefficients of each layer. The kernel of the GAPM algorithm is assembling the local continuity equations into a global linear system, which has addressed the notorious overflow problems commonly encountered by the traditional coefficient propagator matrix approach. To fast and accurately convert the EM fields from the spectral domain into the spatial domain, an efficient twofold inverse Fourier transform (IFT) technique is established for the computation of triaxial EM logging responses. Two main techniques are developed to significantly improve the computation accuracy and speed of IFT. On the one hand, the spectral fields at the first integral quadrant can be used to express the fields at the other three quadrants. Consequently, the original twofold infinite integral is analytically simplified to a semiinfinite one and the computation cost can be reduced by three-fourths. On the other hand, a two-level subtraction scheme is developed to reduce the integral singularity. The first-level subtraction is achieved by separating the primary fields from the total fields. The second-level process includes subtracting the spectral scattered fields of an equivalent transverse isotropic (TI) layered medium, integrating the residual fields, and computing the spatial fields of the TI model. The subtractions on the primary and scattered fields can make the integral convergence increase by more than 10 orders of magnitude in favorable conditions. Numerical experiments demonstrate that the new semianalytical formulas are well suited for any dipping angle and an arbitrary number of layers, as well as for thin and thick formations. The modeling method is efficient and robust, which can provide a fast simulator for the interpretation of triaxial EM logging data.
- 11 December 2022
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 88 (2) , D115-D129
A new semianalytical algorithm for rapid simulation of triaxial electromagnetic logging responses in multilayered biaxial anisotropic formations
A set of compact and stable formulas are developed for the computation of triaxial electromagnetic (EM) logging responses in multilayered formations with biaxial anisotropy. These formulas are based on a new global amplitude propagator matrix (GAPM) algorithm, which derives the amplitudes of upgoing/downgoing waves at the boundaries rather than the reflection/transmission coefficients of each layer. The kernel of the GAPM algorithm is assembling the local continuity equations into a global linear system, which has addressed the notorious overflow problems commonly encountered by the traditional coefficient propagator matrix approach. To fast and accurately convert the EM fields from the spectral domain into the spatial domain, an efficient twofold inverse Fourier transform (IFT) technique is established for the computation of triaxial EM logging responses. Two main techniques are developed to significantly improve the computation accuracy and speed of IFT. On the one hand, the spectral fields at the first integral quadrant can be used to express the fields at the other three quadrants. Consequently, the original twofold infinite integral is analytically simplified to a semiinfinite one and the computation cost can be reduced by three-fourths. On the other hand, a two-level subtraction scheme is developed to reduce the integral singularity. The first-level subtraction is achieved by separating the primary fields from the total fields. The second-level process includes subtracting the spectral scattered fields of an equivalent transverse isotropic (TI) layered medium, integrating the residual fields, and computing the spatial fields of the TI model. The subtractions on the primary and scattered fields can make the integral convergence increase by more than 10 orders of magnitude in favorable conditions. Numerical experiments demonstrate that the new semianalytical formulas are well suited for any dipping angle and an arbitrary number of layers, as well as for thin and thick formations. The modeling method is efficient and robust, which can provide a fast simulator for the interpretation of triaxial EM logging data.
- 10 November 2022
- Published by Society of Exploration Geophysicists in Interpretation
- Vol. 11 (1) , T171-T180
Signal processing methods for crosswell electromagnetic imaging system
The principle of crosswell electromagnetic (EM) imaging is similar to that of induction logging. The difference between them is that conventional induction logging can only measure the formation conductivity within a few meters around the well. However, crosswell EM imaging can be used in two wells with a separation distance of up to 1000 m. Several novel signal processing methods for crosswell EM imaging systems are developed for calibration, casing correction, and hybrid Jacobian matrix calculation. To conveniently perform calibration on the ground, the EM field formula in a vertical layered media is derived based on Maxwell equations, and the relationships between the received signal and frequency, formation conductivity, and transceiver spacing are subsequently derived. Furthermore, a new calibration method is developed. The EM field formula for a radial layered media is derived, and the analytical expressions describing the relationship between the receiving signal and borehole parameters, metal casing parameters, formation parameters, and receiver location are obtained. The effects of mud resistivity, metal casing position, metal casing resistivity, permeability, cement ring resistivity, transmitting frequency, and receiver location on the crosswell EM receiving signal are simulated. It is determined that only the casing required a correction. The influence of the metal casing is corrected by establishing a database. The difference between the corrected data and data obtained without a metal casing is less than 1%. There is a large error in the calculation of the Jacobian matrix in some regions when Green’s function was used. A hybrid Jacobian matrix calculation method combining local perturbation and a global Green’s function is developed, which significantly reduced the error and improved the inversion accuracy.
- 10 November 2022
- Published by Society of Exploration Geophysicists in Interpretation
- Vol. 11 (1) , T171-T180
Signal processing methods for crosswell electromagnetic imaging system
The principle of crosswell electromagnetic (EM) imaging is similar to that of induction logging. The difference between them is that conventional induction logging can only measure the formation conductivity within a few meters around the well. However, crosswell EM imaging can be used in two wells with a separation distance of up to 1000 m. Several novel signal processing methods for crosswell EM imaging systems are developed for calibration, casing correction, and hybrid Jacobian matrix calculation. To conveniently perform calibration on the ground, the EM field formula in a vertical layered media is derived based on Maxwell equations, and the relationships between the received signal and frequency, formation conductivity, and transceiver spacing are subsequently derived. Furthermore, a new calibration method is developed. The EM field formula for a radial layered media is derived, and the analytical expressions describing the relationship between the receiving signal and borehole parameters, metal casing parameters, formation parameters, and receiver location are obtained. The effects of mud resistivity, metal casing position, metal casing resistivity, permeability, cement ring resistivity, transmitting frequency, and receiver location on the crosswell EM receiving signal are simulated. It is determined that only the casing required a correction. The influence of the metal casing is corrected by establishing a database. The difference between the corrected data and data obtained without a metal casing is less than 1%. There is a large error in the calculation of the Jacobian matrix in some regions when Green’s function was used. A hybrid Jacobian matrix calculation method combining local perturbation and a global Green’s function is developed, which significantly reduced the error and improved the inversion accuracy.