Mark Lay
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Mark Lay has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Casparus Johannes Reinhard Verbeek
Centre for Advanced Materials Manufacturing and Design The University of Auckland Auckland New Zealand
6 shared publications - Chanelle Gavin
University of Waikato
4 shared publications - Marianne Hull-Cantillo
School of Engineering, University of Waikato, Private Bag 3105, Hamilton 3240, New Zealand
2 shared publications - Peter Kovalsky
School of Engineering, University of Waikato, Private Bag 3105, Hamilton 3240, New Zealand
2 shared publications - Ahmer Ali Siyal
Micropollutant Research Centre (MPRC), Institute for Integrated Engineering (I2E), Universiti Tun Hussein Onn Malaysia (UTHM), Parit Raja, Malaysia
1 shared publication Ali Shaan Manzoor Ghumman
Department of Chemical Engineering, Universiti Teknologi PETRONAS, 32610 Seri Iskandar, Perak Darul Ridzuan, Malaysia
1 shared publication
Latest Publications
- Open Access
- 15 December 2025
- Published by Akademia Baru Publishing in Semarak Engineering Journal
- Vol. 11 (1) , 68-83
Charge Properties, Characteristics and Applications of Bentonite: A Concise Review
Bentonite belongs to the smectite group of clay with montmorillonite as the primary subunit. Calcium and sodium bentonite are the two common types of bentonite which are used in various fields. As a filler material, surface modification is usually necessary to make bentonite more compatible with matrix materials. During the modification process, elemental additives can intercalate between the clay layers, promoting layer exfoliation. This results in a filler material with very high specific surface area-to-weight ratio. Consequently, even at low filler loading the resulting composites can exhibit significant improvements in mechanical and thermal properties. In aqueous environments, sodium bentonite swells more than its calcium counterpart due to the weaker interlayer bonding by monovalent Na+ ions as compared to the stronger divalent Ca2+ ions. High water uptake could be advantageous in agriculture is but generally regarded as disadvantageous in separation processes such as wastewater treatment and oil & gas drilling exploration. Based on its wide availability, abundance and cost effectiveness, bentonite and other smectite clays are expected to attract more interest in the future. In addition, with various sustainability goals outlined by the United Nations, the use of natural materials like bentonite is projected to expand particularly in countries with substantial natural reserves.
- 15 December 2025
- Published by Akademia Baru Publishing in Semarak Engineering Journal
- Vol. 11 (1) , 68-83
Open AccessCharge Properties, Characteristics and Applications of Bentonite: A Concise Review
Bentonite belongs to the smectite group of clay with montmorillonite as the primary subunit. Calcium and sodium bentonite are the two common types of bentonite which are used in various fields. As a filler material, surface modification is usually necessary to make bentonite more compatible with matrix materials. During the modification process, elemental additives can intercalate between the clay layers, promoting layer exfoliation. This results in a filler material with very high specific surface area-to-weight ratio. Consequently, even at low filler loading the resulting composites can exhibit significant improvements in mechanical and thermal properties. In aqueous environments, sodium bentonite swells more than its calcium counterpart due to the weaker interlayer bonding by monovalent Na+ ions as compared to the stronger divalent Ca2+ ions. High water uptake could be advantageous in agriculture is but generally regarded as disadvantageous in separation processes such as wastewater treatment and oil & gas drilling exploration. Based on its wide availability, abundance and cost effectiveness, bentonite and other smectite clays are expected to attract more interest in the future. In addition, with various sustainability goals outlined by the United Nations, the use of natural materials like bentonite is projected to expand particularly in countries with substantial natural reserves.
- Open Access
- 20 September 2024
- Published by Frontiers Media SA in Frontiers in Microbiology
- Vol. 15, 1437795
Nature based solutions for removal of steroid estrogens in wastewater
Estrogens are a growing problem in wastewater discharges because they are continuously entering the environment and are biologically active at extremely low concentrations. Their effects on wildlife were first identified several decades before, but the environmental limits and the remedial measures are still not completely elucidated. Most conventional treatment processes were not designed with sufficiently long retention times to effectively remove estrogens. Nature-based wastewater treatment technologies such as treatment wetlands (TW) and high-rate algal ponds (HRAP) are economically feasible alternatives for decentralized wastewater treatment and have promise for removing steroid hormones including estrogens. For small communities with populations below 50,000, the overall cost of TWs and HRAPs is considerably lower than that of advanced decentralized treatment technologies such as activated sludge systems (AS) and sequencing batch reactors (SBR). This results from the simplicity of design, use of less materials in construction, lower energy use, operation and maintenance costs, and operation by non-skilled personnel. The nature-based technologies show high removal (>80%) for both natural and synthetic estrogens. Estrogen removal in TWs can be enhanced using alternative media such as palm mulch, biochar, and construction wastes such as bricks, instead of traditional substrates such as sand and gravel. While TWs are effective in estrogen removal, they have the disadvantage of requiring a relatively large footprint, but this can be reduced by using intensified multilayer wetland filters (IMWF). Using filamentous algae in HRAP (high-rate filamentous algal pond; HRFAP) is an emerging technology for wastewater treatment. The algae supply oxygen via photosynthesis and assimilate nutrients into readily harvestable filamentous algal biomass. Diurnal fluctuations in oxygen supply and pH in these systems provide conditions conducive to the breakdown of estrogens and a wide range of other emerging contaminants. The performance of these nature-based systems varies with seasonal changes in environmental conditions (particularly temperature and solar irradiation), however a greater understanding of operating conditions such as loading rate, hydraulic retention time (HRT), pond/bed depth, dissolved oxygen (DO) concentration and pH, which influence the removal mechanisms (biodegradation, sorption and photodegradation) enable TWs and HRAPs to be successfully used for removing estrogens.
- 20 September 2024
- Published by Frontiers Media SA in Frontiers in Microbiology
- Vol. 15, 1437795
Open AccessNature based solutions for removal of steroid estrogens in wastewater
Estrogens are a growing problem in wastewater discharges because they are continuously entering the environment and are biologically active at extremely low concentrations. Their effects on wildlife were first identified several decades before, but the environmental limits and the remedial measures are still not completely elucidated. Most conventional treatment processes were not designed with sufficiently long retention times to effectively remove estrogens. Nature-based wastewater treatment technologies such as treatment wetlands (TW) and high-rate algal ponds (HRAP) are economically feasible alternatives for decentralized wastewater treatment and have promise for removing steroid hormones including estrogens. For small communities with populations below 50,000, the overall cost of TWs and HRAPs is considerably lower than that of advanced decentralized treatment technologies such as activated sludge systems (AS) and sequencing batch reactors (SBR). This results from the simplicity of design, use of less materials in construction, lower energy use, operation and maintenance costs, and operation by non-skilled personnel. The nature-based technologies show high removal (>80%) for both natural and synthetic estrogens. Estrogen removal in TWs can be enhanced using alternative media such as palm mulch, biochar, and construction wastes such as bricks, instead of traditional substrates such as sand and gravel. While TWs are effective in estrogen removal, they have the disadvantage of requiring a relatively large footprint, but this can be reduced by using intensified multilayer wetland filters (IMWF). Using filamentous algae in HRAP (high-rate filamentous algal pond; HRFAP) is an emerging technology for wastewater treatment. The algae supply oxygen via photosynthesis and assimilate nutrients into readily harvestable filamentous algal biomass. Diurnal fluctuations in oxygen supply and pH in these systems provide conditions conducive to the breakdown of estrogens and a wide range of other emerging contaminants. The performance of these nature-based systems varies with seasonal changes in environmental conditions (particularly temperature and solar irradiation), however a greater understanding of operating conditions such as loading rate, hydraulic retention time (HRT), pond/bed depth, dissolved oxygen (DO) concentration and pH, which influence the removal mechanisms (biodegradation, sorption and photodegradation) enable TWs and HRAPs to be successfully used for removing estrogens.
- Open Access
- 29 February 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (3) , 137
The Hard Reality of Biogas Production through the Anaerobic Digestion of Algae Grown in Dairy Farm Effluents
Much emphasis has been given to algal biomass growth in dairy farm wastewater. Most of the systems examined require productive land to be converted and/or freshwater use to dilute high concentrations of nutrients found in dairy effluent. A rotating algal biofilm (RABR) provides the capacity to grow algae without sacrificing productive land or freshwater. In theory, this system would overcome some of the economic and environmental challenges that other systems have. A combination of theoretical information, nutrient uptake formulas, and economic formulas were used to calculate the potential of biogas production from algae grown in an RABR with dairy effluents. The average nutrient uptake was 0.8 mgN/m2 per day and 0.1 mgP/m2 per day. The maximum methane production from the anaerobic digestion of algae was 112 m3/RABR·year. The minimum and maximum economic scenarios resulted in gross profits of NZD −2101 and −1922. After evaluating this system for the first time in the New Zealand dairy farming context, it was found that biogas production from an RABR is not a feasible option for New Zealand dairy farmers.
- 29 February 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (3) , 137
Open AccessThe Hard Reality of Biogas Production through the Anaerobic Digestion of Algae Grown in Dairy Farm Effluents
Much emphasis has been given to algal biomass growth in dairy farm wastewater. Most of the systems examined require productive land to be converted and/or freshwater use to dilute high concentrations of nutrients found in dairy effluent. A rotating algal biofilm (RABR) provides the capacity to grow algae without sacrificing productive land or freshwater. In theory, this system would overcome some of the economic and environmental challenges that other systems have. A combination of theoretical information, nutrient uptake formulas, and economic formulas were used to calculate the potential of biogas production from algae grown in an RABR with dairy effluents. The average nutrient uptake was 0.8 mgN/m2 per day and 0.1 mgP/m2 per day. The maximum methane production from the anaerobic digestion of algae was 112 m3/RABR·year. The minimum and maximum economic scenarios resulted in gross profits of NZD −2101 and −1922. After evaluating this system for the first time in the New Zealand dairy farming context, it was found that biogas production from an RABR is not a feasible option for New Zealand dairy farmers.
- Open Access
Anaerobic Digestion of Dairy Effluent in New Zealand, Time to Revisit the Idea?
The anaerobic digestion of New Zealand low-input dairy farms has previously been evaluated for energy production, but farming systems have recently become more intensive with increased feed supplementation and feed replacement; therefore, we are studying how these changes affect the overall energy production for water heating. A combination of literature review, surveys, chemical analyses, biomethane potential analysis, and modeling were used for this study. On a case study farm with a solid separator, it was found that 558 MJ/day and 176–861 MJ/day could be produced with the solid and liquid portions of effluent, respectively. There is enough biogas to satisfy the dairy farm’s water heating requirements with a tankless water heater.
Open AccessAnaerobic Digestion of Dairy Effluent in New Zealand, Time to Revisit the Idea?
The anaerobic digestion of New Zealand low-input dairy farms has previously been evaluated for energy production, but farming systems have recently become more intensive with increased feed supplementation and feed replacement; therefore, we are studying how these changes affect the overall energy production for water heating. A combination of literature review, surveys, chemical analyses, biomethane potential analysis, and modeling were used for this study. On a case study farm with a solid separator, it was found that 558 MJ/day and 176–861 MJ/day could be produced with the solid and liquid portions of effluent, respectively. There is enough biogas to satisfy the dairy farm’s water heating requirements with a tankless water heater.
- 1 August 2019
- Published by Elsevier in Polymer Testing
- Vol. 77, 105876
Thermal analysis and secondary structure of protein fractions in a highly aggregated protein material
- 1 August 2019
- Published by Elsevier in Polymer Testing
- Vol. 77, 105876
Thermal analysis and secondary structure of protein fractions in a highly aggregated protein material
- 1 February 2019
- Published by Elsevier in Polymer Testing
- Vol. 73, 82-86
Formation of secondary structures in protein foams as detected by synchrotron FT-IR
- 1 February 2019
- Published by Elsevier in Polymer Testing
- Vol. 73, 82-86
Formation of secondary structures in protein foams as detected by synchrotron FT-IR
- Open Access
High-Speed Imaging of Paw Withdrawal Reflex to Objectively Assess Pain State in Mice
Rodents are often used for studying chronic pain mechanisms and developing new pain therapeutics, but objectively determining the animal’s pain state is a major challenge. To improve the precision of using reflexive withdrawal behaviors for interpreting the mouse pain state, we adopted high-speed videography to capture sub-second movement features of mice upon hind paw stimulation. We identified several parameters that are significantly different between behaviors evoked by innocuous and noxious stimuli, and combined them to map the mouse pain state through statistical modeling and machine learning. To test the utility of this approach, we determined the pain state triggered by von Frey hairs (VFHs) and optogenetic activation of two nociceptor populations. Our method reliably assesses the “pain-like” probability for each mouse paw withdrawal reflex under all scenarios, highlighting the improved precision of using this high resolution behavior-centered composite methodology to determine the mouse pain state from reflexive withdrawal assays.
Open AccessHigh-Speed Imaging of Paw Withdrawal Reflex to Objectively Assess Pain State in Mice
Rodents are often used for studying chronic pain mechanisms and developing new pain therapeutics, but objectively determining the animal’s pain state is a major challenge. To improve the precision of using reflexive withdrawal behaviors for interpreting the mouse pain state, we adopted high-speed videography to capture sub-second movement features of mice upon hind paw stimulation. We identified several parameters that are significantly different between behaviors evoked by innocuous and noxious stimuli, and combined them to map the mouse pain state through statistical modeling and machine learning. To test the utility of this approach, we determined the pain state triggered by von Frey hairs (VFHs) and optogenetic activation of two nociceptor populations. Our method reliably assesses the “pain-like” probability for each mouse paw withdrawal reflex under all scenarios, highlighting the improved precision of using this high resolution behavior-centered composite methodology to determine the mouse pain state from reflexive withdrawal assays.
- 1 January 2017
- Published by AIP Publishing
Foaming behavior of novatein and blends with polyethylene compatibilised by maleic anhydride
Novatein® thermoplastic protein (NTP), a bloodmeal based thermoplastic, was successfully foamed without blowing agent or blending with other polymers using a BOY-35A injection moulder in free expansion mode. Previously, only soy protein has been successfully continuously foamed and zein and gluten batch foamed without blending or rheological modification. The greatest expansion ratio for NTP was 4.4 at 165°C. Blending NTP with compatibilised LLDPE and LDPE and adding blowing agent reduced expansion ratios. The foams exhibited a fibrous nature, with cell structures similar to those reported in literature for extrusion foamed thermoplastic soy protein isolate. SEM pictures suggested a possible role of either sodium sulphite, sodium dodecyl sulphate or sodium sulphate as a nucleating agent as particulates were found on the cell surfaces. Triethylene glycol and urea were thought to contribute to NTP foaming, along with water present in NTP, with two or more acting as the blowing agent.
- 1 January 2017
- Published by AIP Publishing
Foaming behavior of novatein and blends with polyethylene compatibilised by maleic anhydride
Novatein® thermoplastic protein (NTP), a bloodmeal based thermoplastic, was successfully foamed without blowing agent or blending with other polymers using a BOY-35A injection moulder in free expansion mode. Previously, only soy protein has been successfully continuously foamed and zein and gluten batch foamed without blending or rheological modification. The greatest expansion ratio for NTP was 4.4 at 165°C. Blending NTP with compatibilised LLDPE and LDPE and adding blowing agent reduced expansion ratios. The foams exhibited a fibrous nature, with cell structures similar to those reported in literature for extrusion foamed thermoplastic soy protein isolate. SEM pictures suggested a possible role of either sodium sulphite, sodium dodecyl sulphate or sodium sulphate as a nucleating agent as particulates were found on the cell surfaces. Triethylene glycol and urea were thought to contribute to NTP foaming, along with water present in NTP, with two or more acting as the blowing agent.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1713, 100006
Blending Novatein® thermoplastic protein with PLA for carbon dioxide assisted batch foaming
The convenience of polymeric foams has led to their widespread utilisation in everyday life. However, disposal of synthetic petroleum-derived foams has had a detrimental effect on the environment which needs to be addressed. This study uses a clean and sustainable approach to investigate the foaming capability of a blend of two biodegradable polymers, polylactic acid (PLA) and Novatein® Thermoplastic Protein (NTP). PLA, derived from corn starch, can successfully be foamed using a batch technique developed by the Biopolymer Network Ltd. NTP is a patented formulation of bloodmeal and chemical additives which can be extruded and injection moulded similar to other thermoplastics. However, foaming NTP is a new area of study and its interaction with blowing agents in the batch process is entirely unknown. Subcritical and supercritical carbon dioxide have been examined individually in two uniquely designed pressure vessels to foam various compositions of NTP-PLA blends. Foamed material were characterised in terms of expansion ratio, cell size, and cellular morphology in order to study how the composition of NTP-PLA affects foaming with carbon dioxide. It was found that blends with 5 wt. % NTP foamed using subcritical CO2 expanded up to 11 times due to heterogeneous nucleation. Morphology analysis using scanning electron microscopy showed that foams blown with supercritical CO2 had a finer cell structure with consistent cell size, whereas, foams blown with subcritical CO2 ranged in cell size and showed cell wall rupture. Ultimately, this research would contribute to the production of a biodegradable foam material to be used in packaging applications, thereby adding to the application potential of NTP.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1713, 100006
Blending Novatein® thermoplastic protein with PLA for carbon dioxide assisted batch foaming
The convenience of polymeric foams has led to their widespread utilisation in everyday life. However, disposal of synthetic petroleum-derived foams has had a detrimental effect on the environment which needs to be addressed. This study uses a clean and sustainable approach to investigate the foaming capability of a blend of two biodegradable polymers, polylactic acid (PLA) and Novatein® Thermoplastic Protein (NTP). PLA, derived from corn starch, can successfully be foamed using a batch technique developed by the Biopolymer Network Ltd. NTP is a patented formulation of bloodmeal and chemical additives which can be extruded and injection moulded similar to other thermoplastics. However, foaming NTP is a new area of study and its interaction with blowing agents in the batch process is entirely unknown. Subcritical and supercritical carbon dioxide have been examined individually in two uniquely designed pressure vessels to foam various compositions of NTP-PLA blends. Foamed material were characterised in terms of expansion ratio, cell size, and cellular morphology in order to study how the composition of NTP-PLA affects foaming with carbon dioxide. It was found that blends with 5 wt. % NTP foamed using subcritical CO2 expanded up to 11 times due to heterogeneous nucleation. Morphology analysis using scanning electron microscopy showed that foams blown with supercritical CO2 had a finer cell structure with consistent cell size, whereas, foams blown with subcritical CO2 ranged in cell size and showed cell wall rupture. Ultimately, this research would contribute to the production of a biodegradable foam material to be used in packaging applications, thereby adding to the application potential of NTP.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1713, 100003
Extrusion foaming of protein-based thermoplastic and polyethylene blends
Currently the extrusion foamability of Novatein® Thermoplastic Protein (NTP) is being investigated at the University of Waikato in collaboration with the Biopolymer Network Ltd (NZ). NTP has been developed from bloodmeal (>86 wt% protein), a co-product of the meat industry, by adding denaturants and plasticisers (tri-ethylene glycol and water) allowing it to be extruded and injection moulded. NTP alone does not readily foam when sodium bicarbonate is used as a chemical blowing agent as its extensional viscosity is too high. The thermoplastic properties of NTP were modified by blending it with different weight fractions of linear low density polyethylene (LLDPE) and polyethylene grafted maleic anhydride (PE-g-MAH) compatibiliser. Extrusion foaming was conducted in two ways, firstly using the existing water content in the material as the blowing agent and secondly by adding sodium bicarbonate. When processed in a twin screw extruder (L/D 25 and 10 mm die) the material readily expanded due to the internal moisture content alone, with a conditioned expansion ratio of up to ± 0.13. Cell structure was non-uniform exhibiting a broad range cell sizes at various stages of formation with some coalescence. The cell size reduced through the addition of sodium bicarbonate, overall more cells were observed and the structure was more uniform, however ruptured cells were also visible on the extrudate skin. Increasing die temperature and introducing water cooling reduced cell size, but the increased die temperature resulted in surface degradation.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1713, 100003
Extrusion foaming of protein-based thermoplastic and polyethylene blends
Currently the extrusion foamability of Novatein® Thermoplastic Protein (NTP) is being investigated at the University of Waikato in collaboration with the Biopolymer Network Ltd (NZ). NTP has been developed from bloodmeal (>86 wt% protein), a co-product of the meat industry, by adding denaturants and plasticisers (tri-ethylene glycol and water) allowing it to be extruded and injection moulded. NTP alone does not readily foam when sodium bicarbonate is used as a chemical blowing agent as its extensional viscosity is too high. The thermoplastic properties of NTP were modified by blending it with different weight fractions of linear low density polyethylene (LLDPE) and polyethylene grafted maleic anhydride (PE-g-MAH) compatibiliser. Extrusion foaming was conducted in two ways, firstly using the existing water content in the material as the blowing agent and secondly by adding sodium bicarbonate. When processed in a twin screw extruder (L/D 25 and 10 mm die) the material readily expanded due to the internal moisture content alone, with a conditioned expansion ratio of up to ± 0.13. Cell structure was non-uniform exhibiting a broad range cell sizes at various stages of formation with some coalescence. The cell size reduced through the addition of sodium bicarbonate, overall more cells were observed and the structure was more uniform, however ruptured cells were also visible on the extrudate skin. Increasing die temperature and introducing water cooling reduced cell size, but the increased die temperature resulted in surface degradation.