Chanelle Gavin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chanelle Gavin has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Casparus Johannes Reinhard Verbeek
Centre for Advanced Materials Manufacturing and Design The University of Auckland Auckland New Zealand
5 shared publications - Mark Lay
School of Science and Engineering, University of Waikato, Private Bag 3105, Hamilton 3240, New Zealand
4 shared publications Mark C. Lay
School of Engineering, Faculty of Science and Engineering University of Waikato Knighton Road, Hamilton 3240 New Zealand
3 shared publicationsCasparus J. R. Verbeek
University of Waikato
2 shared publications- Christian Gauss
School of Engineering, University of Waikato, Hamilton 3240, New Zealand
1 shared publication Christopher N. Battershill
Univ Waikato, Sch Sci, Coastal Marine Field Stn, Tauranga, New Zealand
1 shared publication
Latest Publications
- Open Access
- 15 October 2026
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 34
Starch-gelatine active packaging: A critical review of processing scalability, sustainable additives, and testing standardization
Starch-gelatine films are promising biodegradable materials for active food packaging, but their industrial adoption beyond laboratory-scale studies is currently limited by formulation-dependent performance, processing limitations and inconsistent experimental reporting. This critical review demonstrates how formulation, processing history, polymer architecture and environmental conditions determine the mechanical, barrier and active properties of starch–gelatine films. Solution casting is widely used for laboratory studies, whereas extrusion, thermo-compression and related thermoplastic methods provide a more direct pathway to continuous manufacture. However, published evidence for process robustness, thermal stability, throughput and post-processing barrier performance is limited. Natural antioxidants and agro-industrial by-products can provide antioxidant, antimicrobial or sensing functionality, but their effectiveness depends on matrix interactions, retention, release or migration and validation in food systems. Relative humidity is also critical because water sorption and plasticization can strongly affect water vapor and oxygen transport. A further limitation is not the absence of recognized standards, but their inconsistent adoption and implementation, together with incomplete reporting of key test conditions across studies. This review proposes an integrated framework linking processing–structure–property relationships with minimum reporting requirements, food-contact safety, application validation and industrial scalability, while identifying future priorities in quantitative structure–property analysis, pilot-scale process validation and standardized reporting to support reliable data-driven design.
- 15 October 2026
- Published by SAGE Publications in Polymers and Polymer Composites
- Vol. 34
Open AccessStarch-gelatine active packaging: A critical review of processing scalability, sustainable additives, and testing standardization
Starch-gelatine films are promising biodegradable materials for active food packaging, but their industrial adoption beyond laboratory-scale studies is currently limited by formulation-dependent performance, processing limitations and inconsistent experimental reporting. This critical review demonstrates how formulation, processing history, polymer architecture and environmental conditions determine the mechanical, barrier and active properties of starch–gelatine films. Solution casting is widely used for laboratory studies, whereas extrusion, thermo-compression and related thermoplastic methods provide a more direct pathway to continuous manufacture. However, published evidence for process robustness, thermal stability, throughput and post-processing barrier performance is limited. Natural antioxidants and agro-industrial by-products can provide antioxidant, antimicrobial or sensing functionality, but their effectiveness depends on matrix interactions, retention, release or migration and validation in food systems. Relative humidity is also critical because water sorption and plasticization can strongly affect water vapor and oxygen transport. A further limitation is not the absence of recognized standards, but their inconsistent adoption and implementation, together with incomplete reporting of key test conditions across studies. This review proposes an integrated framework linking processing–structure–property relationships with minimum reporting requirements, food-contact safety, application validation and industrial scalability, while identifying future priorities in quantitative structure–property analysis, pilot-scale process validation and standardized reporting to support reliable data-driven design.
- Open Access
- 16 May 2024
- Published by Elsevier in Bioresource Technology
- Vol. 403, 130850
Quality of cellulose and biostimulant extracts from Oedogonium calcareum cultivated during primary wastewater treatment
- 16 May 2024
- Published by Elsevier in Bioresource Technology
- Vol. 403, 130850
Open AccessQuality of cellulose and biostimulant extracts from Oedogonium calcareum cultivated during primary wastewater treatment
- 1 August 2019
- Published by Elsevier in Polymer Testing
- Vol. 77, 105876
Thermal analysis and secondary structure of protein fractions in a highly aggregated protein material
- 1 August 2019
- Published by Elsevier in Polymer Testing
- Vol. 77, 105876
Thermal analysis and secondary structure of protein fractions in a highly aggregated protein material
- 3 April 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 136 (30)
The role of plasticizers during protein thermoplastic foaming
Protein thermoplastics, like Novatein, typically comprise a polymer, additives, and plasticizers. During foaming, the plasticizers performed different functions; triethylene glycol (TEG) affected the Tg of the polymer, while water altered the shear viscosity and urea the extensional viscosity. Water and urea also functioned as blowing agents; increasing urea increased the expansion ratio, while an increase in TEG and water decreased it. It was concluded that at this level of plasticization, phase separation occurred and that the plasticizers are most influential during late bubble growth and stabilization. Contrary to previous thought, increasing water had no effect on the Tg, but did lower the shear viscosity, while increasing TEG had the opposite effect. This enables the properties of protein thermoplastics to be tailored during development. During foaming, lower viscosity allows more time for gases to diffuse before the viscosity in the surrounding polymer increases, restricting bubble growth. At higher TEG content, the material is processed further above its Tg, slowing down stabilization and decreasing expansion. This study clarified the role of plasticizers during foaming and showed a decrease in random coils and β‐turns (measured by FT‐IR) with increasing expansion ratio. Knowledge of these mechanisms enables tailoring properties of protein thermoplastics foams during development. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47781.
- 3 April 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 136 (30)
The role of plasticizers during protein thermoplastic foaming
Protein thermoplastics, like Novatein, typically comprise a polymer, additives, and plasticizers. During foaming, the plasticizers performed different functions; triethylene glycol (TEG) affected the Tg of the polymer, while water altered the shear viscosity and urea the extensional viscosity. Water and urea also functioned as blowing agents; increasing urea increased the expansion ratio, while an increase in TEG and water decreased it. It was concluded that at this level of plasticization, phase separation occurred and that the plasticizers are most influential during late bubble growth and stabilization. Contrary to previous thought, increasing water had no effect on the Tg, but did lower the shear viscosity, while increasing TEG had the opposite effect. This enables the properties of protein thermoplastics to be tailored during development. During foaming, lower viscosity allows more time for gases to diffuse before the viscosity in the surrounding polymer increases, restricting bubble growth. At higher TEG content, the material is processed further above its Tg, slowing down stabilization and decreasing expansion. This study clarified the role of plasticizers during foaming and showed a decrease in random coils and β‐turns (measured by FT‐IR) with increasing expansion ratio. Knowledge of these mechanisms enables tailoring properties of protein thermoplastics foams during development. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47781.
- 1 February 2019
- Published by Elsevier in Polymer Testing
- Vol. 73, 82-86
Formation of secondary structures in protein foams as detected by synchrotron FT-IR
- 1 February 2019
- Published by Elsevier in Polymer Testing
- Vol. 73, 82-86
Formation of secondary structures in protein foams as detected by synchrotron FT-IR
- 30 July 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (22) , 15703-15716
Morphology and compressive behaviour of foams produced from thermoplastic protein
- 30 July 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 53 (22) , 15703-15716
Morphology and compressive behaviour of foams produced from thermoplastic protein
- 1 December 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (13) , 46005
Conformational changes after foaming in a protein‐based thermoplastic
Novatein is a biopolymer produced from blood meal and can be foamed for use as a packaging material. The effect of foaming on protein ordered structures such as α‐helices and β‐sheets was investigated using synchrotron Fourier transform infrared (FTIR). Foaming caused a reduction in ordered structures due to an increase in random coils. FTIR also revealed a higher proportion of plasticizer (triethylene glycol, TEG) and β‐sheets toward the surface of enclosed bubbles. Increased TEG will assist foaming with greater plasticization aiding nucleation, while β‐sheets contribute to bubble stabilization. These structural changes occur as foaming takes place close to the degradation temperature of Novatein, and coincide with melting of α‐helices and/or β‐sheets. A more amorphous polymer is therefore produced which is subsequently easier to foam due to its increased elasticity. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46005.
- 1 December 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (13) , 46005
Conformational changes after foaming in a protein‐based thermoplastic
Novatein is a biopolymer produced from blood meal and can be foamed for use as a packaging material. The effect of foaming on protein ordered structures such as α‐helices and β‐sheets was investigated using synchrotron Fourier transform infrared (FTIR). Foaming caused a reduction in ordered structures due to an increase in random coils. FTIR also revealed a higher proportion of plasticizer (triethylene glycol, TEG) and β‐sheets toward the surface of enclosed bubbles. Increased TEG will assist foaming with greater plasticization aiding nucleation, while β‐sheets contribute to bubble stabilization. These structural changes occur as foaming takes place close to the degradation temperature of Novatein, and coincide with melting of α‐helices and/or β‐sheets. A more amorphous polymer is therefore produced which is subsequently easier to foam due to its increased elasticity. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46005.
- 1 January 2017
- Published by AIP Publishing
Foaming behavior of novatein and blends with polyethylene compatibilised by maleic anhydride
Novatein® thermoplastic protein (NTP), a bloodmeal based thermoplastic, was successfully foamed without blowing agent or blending with other polymers using a BOY-35A injection moulder in free expansion mode. Previously, only soy protein has been successfully continuously foamed and zein and gluten batch foamed without blending or rheological modification. The greatest expansion ratio for NTP was 4.4 at 165°C. Blending NTP with compatibilised LLDPE and LDPE and adding blowing agent reduced expansion ratios. The foams exhibited a fibrous nature, with cell structures similar to those reported in literature for extrusion foamed thermoplastic soy protein isolate. SEM pictures suggested a possible role of either sodium sulphite, sodium dodecyl sulphate or sodium sulphate as a nucleating agent as particulates were found on the cell surfaces. Triethylene glycol and urea were thought to contribute to NTP foaming, along with water present in NTP, with two or more acting as the blowing agent.
- 1 January 2017
- Published by AIP Publishing
Foaming behavior of novatein and blends with polyethylene compatibilised by maleic anhydride
Novatein® thermoplastic protein (NTP), a bloodmeal based thermoplastic, was successfully foamed without blowing agent or blending with other polymers using a BOY-35A injection moulder in free expansion mode. Previously, only soy protein has been successfully continuously foamed and zein and gluten batch foamed without blending or rheological modification. The greatest expansion ratio for NTP was 4.4 at 165°C. Blending NTP with compatibilised LLDPE and LDPE and adding blowing agent reduced expansion ratios. The foams exhibited a fibrous nature, with cell structures similar to those reported in literature for extrusion foamed thermoplastic soy protein isolate. SEM pictures suggested a possible role of either sodium sulphite, sodium dodecyl sulphate or sodium sulphate as a nucleating agent as particulates were found on the cell surfaces. Triethylene glycol and urea were thought to contribute to NTP foaming, along with water present in NTP, with two or more acting as the blowing agent.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1713, 100003
Extrusion foaming of protein-based thermoplastic and polyethylene blends
Currently the extrusion foamability of Novatein® Thermoplastic Protein (NTP) is being investigated at the University of Waikato in collaboration with the Biopolymer Network Ltd (NZ). NTP has been developed from bloodmeal (>86 wt% protein), a co-product of the meat industry, by adding denaturants and plasticisers (tri-ethylene glycol and water) allowing it to be extruded and injection moulded. NTP alone does not readily foam when sodium bicarbonate is used as a chemical blowing agent as its extensional viscosity is too high. The thermoplastic properties of NTP were modified by blending it with different weight fractions of linear low density polyethylene (LLDPE) and polyethylene grafted maleic anhydride (PE-g-MAH) compatibiliser. Extrusion foaming was conducted in two ways, firstly using the existing water content in the material as the blowing agent and secondly by adding sodium bicarbonate. When processed in a twin screw extruder (L/D 25 and 10 mm die) the material readily expanded due to the internal moisture content alone, with a conditioned expansion ratio of up to ± 0.13. Cell structure was non-uniform exhibiting a broad range cell sizes at various stages of formation with some coalescence. The cell size reduced through the addition of sodium bicarbonate, overall more cells were observed and the structure was more uniform, however ruptured cells were also visible on the extrudate skin. Increasing die temperature and introducing water cooling reduced cell size, but the increased die temperature resulted in surface degradation.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1713, 100003
Extrusion foaming of protein-based thermoplastic and polyethylene blends
Currently the extrusion foamability of Novatein® Thermoplastic Protein (NTP) is being investigated at the University of Waikato in collaboration with the Biopolymer Network Ltd (NZ). NTP has been developed from bloodmeal (>86 wt% protein), a co-product of the meat industry, by adding denaturants and plasticisers (tri-ethylene glycol and water) allowing it to be extruded and injection moulded. NTP alone does not readily foam when sodium bicarbonate is used as a chemical blowing agent as its extensional viscosity is too high. The thermoplastic properties of NTP were modified by blending it with different weight fractions of linear low density polyethylene (LLDPE) and polyethylene grafted maleic anhydride (PE-g-MAH) compatibiliser. Extrusion foaming was conducted in two ways, firstly using the existing water content in the material as the blowing agent and secondly by adding sodium bicarbonate. When processed in a twin screw extruder (L/D 25 and 10 mm die) the material readily expanded due to the internal moisture content alone, with a conditioned expansion ratio of up to ± 0.13. Cell structure was non-uniform exhibiting a broad range cell sizes at various stages of formation with some coalescence. The cell size reduced through the addition of sodium bicarbonate, overall more cells were observed and the structure was more uniform, however ruptured cells were also visible on the extrudate skin. Increasing die temperature and introducing water cooling reduced cell size, but the increased die temperature resulted in surface degradation.