Dennis van der Burg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Dennis van der Burg has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Arno Volker
TNO, Oude Waalsdorperweg 63, P.O.box 96864, 2509 JG The Hague, The Netherlands
1 shared publication E.J.W. Merks-Swolfs
TNO Department of Acoustics & Sonar The Hague 2597 AK , The Netherlands
1 shared publication- Jan-Willem Vrolijk
The Netherlands Organization for Applied Scientific Research (TNO), Oude Waalsdorperweg 63, 2597 AK The Hague, The Netherlands
1 shared publication - Maurits van der Heiden
Nederlandse Organisatie voor Toegepast Natuurwetenschappelijk Onderzoek (TNO) Oude Waalsdorperweg 63 Den Haag 2509JG Netherlands
1 shared publication - Q.E.V.N. Martina
The Netherlands Organization for Applied Scientific Research (TNO), Oude Waalsdorperweg 63, 2597 AK The Hague, The Netherlands
1 shared publication
Latest Publications
- Open Access
- 2 March 2023
- Published by ASME International in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
- Vol. 6 (4) , 1-22
Non-Contact MEMS-Sensor Array Inspection of Composites and Metallic Parts Using Lamb Waves
Composite materials are becoming more popular in the aerospace industry, because of their physical properties. In quality assurance and in-service inspection, there is a need for fast, non-contact, high-quality, non-destructive inspection techniques. The most common approach is to perform the inspection using water-coupled high-frequency transducers. Full wavefield techniques are promising to replace the conventional inspection approach. However, these are currently performed by a laser vibrometer setup, which has drawbacks. As an alternative, a low-cost micro-electro-mechanical system (MEMS) sensor array and dedicated processing scheme are presented enabling fast inspection of large samples. This inspection approach uses a piezoelectric actuator to excite the composite or metallic part with Lamb waves. An array of MEMS sensors records the energy that radiates into the surrounding air. A dedicated processing scheme will translate the measured wavefield into a thickness map of the inspected part. For composite parts, the material’s anisotropy needs to be taken into account for accurate thickness mapping. In principle, all relevant defects show up as local thickness reductions. The results in this paper are obtained with a MEMS-sensor array of 128 elements capable of detecting ultrasound up to 250 kHz at a typical stand-off distance of 100 mm. Defects up to 6 mm in diameter could be detected in thick panels, and defects as small as 2.5 mm could be detected in thin panels. A full-size fuselage experiment shows that the method is also suited for fast inspection of large inspection areas.
- 2 March 2023
- Published by ASME International in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
- Vol. 6 (4) , 1-22
Open AccessNon-Contact MEMS-Sensor Array Inspection of Composites and Metallic Parts Using Lamb Waves
Composite materials are becoming more popular in the aerospace industry, because of their physical properties. In quality assurance and in-service inspection, there is a need for fast, non-contact, high-quality, non-destructive inspection techniques. The most common approach is to perform the inspection using water-coupled high-frequency transducers. Full wavefield techniques are promising to replace the conventional inspection approach. However, these are currently performed by a laser vibrometer setup, which has drawbacks. As an alternative, a low-cost micro-electro-mechanical system (MEMS) sensor array and dedicated processing scheme are presented enabling fast inspection of large samples. This inspection approach uses a piezoelectric actuator to excite the composite or metallic part with Lamb waves. An array of MEMS sensors records the energy that radiates into the surrounding air. A dedicated processing scheme will translate the measured wavefield into a thickness map of the inspected part. For composite parts, the material’s anisotropy needs to be taken into account for accurate thickness mapping. In principle, all relevant defects show up as local thickness reductions. The results in this paper are obtained with a MEMS-sensor array of 128 elements capable of detecting ultrasound up to 250 kHz at a typical stand-off distance of 100 mm. Defects up to 6 mm in diameter could be detected in thick panels, and defects as small as 2.5 mm could be detected in thin panels. A full-size fuselage experiment shows that the method is also suited for fast inspection of large inspection areas.