Sungwoon Hwang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sungwoon Hwang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Byeongcheol Yoon
Department of Electrical Engineering, Hanyang University, Ansan, South Korea
6 shared publications - Junghyun Kim
Hanyang University
6 shared publications - Jooyoung Jeon
Department of Electronic Engineering, Gangreung Wonju National University, Gangreung, South Korea
4 shared publications - Sooji Bae
Department of Electrical Engineering, Hanyang University, Ansan, South Korea
4 shared publications - Sungyoon Kang
Department of Electrical Engineering, Hanyang University, Ansan, South Korea
3 shared publications Byongchang Jeong
Department of Urology, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul, South Korea
2 shared publications
Latest Publications
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (6) , 848-851
A Broadband Doherty-Like Load-Modulated Balanced Amplifier With an Optimized Impedance Transformation Ratio in InGaP/GaAs HBT Process for Handset Applications
This letter presents a design methodology for implementing broadband load-modulated balanced amplifier (LMBA) for handset applications. It is evaluated which architecture, Doherty-like LMBA (DL-LMBA) or pseudo-Doherty LMBA (PD-LMBA), is more suitable for InGaP/GaAs HBT power amplifier (PA). The impedance transformation ratio (ITR) is optimized through an analysis of correlation between the coupler impedance ( $Z_{0}$ ) and matching network (MN). A prototype LMBA attains measured saturation power ( $P_{\text {SAT}}$ ), collector efficiency (CE), and 6-dB output power back-off (OBO) CE of over 33.2 dBm, 45.2%, and 42.0%, respectively, in the range of 3.2–5.0 GHz. The LMBA is also evaluated by 5G NR FR1 100-MHz QPSK CP-OFDM with 9.5-dB peak-to-average power ratio (PAPR), achieving 26.6-dBm average output power ( $P_{\text {avg}}$ ) with 37.7% average CE (CEavg) at an adjacent channel leakage ratio (ACLR) of −33 dBc.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (6) , 848-851
A Broadband Doherty-Like Load-Modulated Balanced Amplifier With an Optimized Impedance Transformation Ratio in InGaP/GaAs HBT Process for Handset Applications
This letter presents a design methodology for implementing broadband load-modulated balanced amplifier (LMBA) for handset applications. It is evaluated which architecture, Doherty-like LMBA (DL-LMBA) or pseudo-Doherty LMBA (PD-LMBA), is more suitable for InGaP/GaAs HBT power amplifier (PA). The impedance transformation ratio (ITR) is optimized through an analysis of correlation between the coupler impedance ( $Z_{0}$ ) and matching network (MN). A prototype LMBA attains measured saturation power ( $P_{\text {SAT}}$ ), collector efficiency (CE), and 6-dB output power back-off (OBO) CE of over 33.2 dBm, 45.2%, and 42.0%, respectively, in the range of 3.2–5.0 GHz. The LMBA is also evaluated by 5G NR FR1 100-MHz QPSK CP-OFDM with 9.5-dB peak-to-average power ratio (PAPR), achieving 26.6-dBm average output power ( $P_{\text {avg}}$ ) with 37.7% average CE (CEavg) at an adjacent channel leakage ratio (ACLR) of −33 dBc.
- 17 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (1) , 575-588
A 5.15–7.125-GHz Differential Power Amplifier With Enhanced Linearity of Average Power Region Using Dynamic Cross-Coupled Capacitor
This article presents a 5.15–7.125-GHz differential power amplifier (PA) with enhanced linear output power by dynamic cross-coupled capacitors ( $C_{\text{cc}}$ ) for both fifth-generation new radio-unlicensed (5G NR-U) and 802.11ax wireless local area network (WLAN) applications. The proposed dynamic $C_{\text{cc}}$ compensates for nonlinear parameters of transistors and leads to improved linearity in the average output power region. The multicoupled four-way transformer (TF) is also proposed for a high symmetry combining structure to reduce the imbalance of differential PA and for a 30% fractional bandwidth of optimal output matching with a low turn ratio and low insertion losses to implement on a nine-layer printed circuit board applications. The proposed differential PA is implemented in a 2- $\mu\text{m}$ InGaP/GaAs heterojunction bipolar transistor (HBT) process. The PA achieves a gain of 24 dB, a saturated output power of 33.1 dBm, and a power added efficiency (PAE) of 40.4% with a collector voltage of 5.5 V over 5.15–7.125 GHz under a continuous wave (CW) signal. The linearity of the proposed PA is further evaluated with various modulation signal schemes to validate its suitability for NR-U and WLAN applications. The PA with NR 100-MHz cyclic prefix (CP) and discrete Fourier transform (DFT) signal having a peak-to-average power ratio (PAPR) of 11.4 and 8 dB achieves linear output power meeting $-$ 33 dBc of 24.6 and 27 dBm and PAE of 10% and 16.3% in NR evolved universal terrestrial radio access (E-UTRA) adjacent channel leakage ratio (ACLR) condition. The PA also achieves the output power of 19.8 dBm with a PAE of 4.3% (error vector magnitude (EVM) $=$ $-$ 40 dB) under 802.11ax MCS11 80 MHz having a PAPR of 10.7 dB.
- 17 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (1) , 575-588
A 5.15–7.125-GHz Differential Power Amplifier With Enhanced Linearity of Average Power Region Using Dynamic Cross-Coupled Capacitor
This article presents a 5.15–7.125-GHz differential power amplifier (PA) with enhanced linear output power by dynamic cross-coupled capacitors ( $C_{\text{cc}}$ ) for both fifth-generation new radio-unlicensed (5G NR-U) and 802.11ax wireless local area network (WLAN) applications. The proposed dynamic $C_{\text{cc}}$ compensates for nonlinear parameters of transistors and leads to improved linearity in the average output power region. The multicoupled four-way transformer (TF) is also proposed for a high symmetry combining structure to reduce the imbalance of differential PA and for a 30% fractional bandwidth of optimal output matching with a low turn ratio and low insertion losses to implement on a nine-layer printed circuit board applications. The proposed differential PA is implemented in a 2- $\mu\text{m}$ InGaP/GaAs heterojunction bipolar transistor (HBT) process. The PA achieves a gain of 24 dB, a saturated output power of 33.1 dBm, and a power added efficiency (PAE) of 40.4% with a collector voltage of 5.5 V over 5.15–7.125 GHz under a continuous wave (CW) signal. The linearity of the proposed PA is further evaluated with various modulation signal schemes to validate its suitability for NR-U and WLAN applications. The PA with NR 100-MHz cyclic prefix (CP) and discrete Fourier transform (DFT) signal having a peak-to-average power ratio (PAPR) of 11.4 and 8 dB achieves linear output power meeting $-$ 33 dBc of 24.6 and 27 dBm and PAE of 10% and 16.3% in NR evolved universal terrestrial radio access (E-UTRA) adjacent channel leakage ratio (ACLR) condition. The PA also achieves the output power of 19.8 dBm with a PAE of 4.3% (error vector magnitude (EVM) $=$ $-$ 40 dB) under 802.11ax MCS11 80 MHz having a PAPR of 10.7 dB.
- 31 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 17 (5) , 1125-1134
GaN-Based 4-MHz Full-Bridge Electrosurgical Generator Using Zero-Voltage Switching Over Wide Load Impedance Range
In this study, a 4-MHz full-bridge inverter system for an electrosurgical generator (ESG) is presented with zero-voltage switching (ZVS) turn-on over a wide load impedance range based on wideband gap material gallium nitride (GaN) technology. The proposed resonant circuit is used for impedance matching and limits the current when the load is short state while performing ZVS over a wide load impedance range. It also ensures high power performance at high frequencies for electric surgery. The implementation methods of the GaN switch at 4 MHz with high output performance are guided by the low inductance from the gate-driver output to the switch gate node and the effective heating management structure of the GaN-based inverter. The proposed generator achieved a maximum output power of 99 W to the load and a maximum overall efficiency of 89% with overcurrent of <3 A at short state of the load. The ESG can generate constant output power of 20, 50, 70 W through mode control of 2, 5, and 7 s. The overcurrent Moreover, the proposed generator is tested on porcine tissue samples to verify its effectiveness as an ESG.
- 31 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 17 (5) , 1125-1134
GaN-Based 4-MHz Full-Bridge Electrosurgical Generator Using Zero-Voltage Switching Over Wide Load Impedance Range
In this study, a 4-MHz full-bridge inverter system for an electrosurgical generator (ESG) is presented with zero-voltage switching (ZVS) turn-on over a wide load impedance range based on wideband gap material gallium nitride (GaN) technology. The proposed resonant circuit is used for impedance matching and limits the current when the load is short state while performing ZVS over a wide load impedance range. It also ensures high power performance at high frequencies for electric surgery. The implementation methods of the GaN switch at 4 MHz with high output performance are guided by the low inductance from the gate-driver output to the switch gate node and the effective heating management structure of the GaN-based inverter. The proposed generator achieved a maximum output power of 99 W to the load and a maximum overall efficiency of 89% with overcurrent of <3 A at short state of the load. The ESG can generate constant output power of 20, 50, 70 W through mode control of 2, 5, and 7 s. The overcurrent Moreover, the proposed generator is tested on porcine tissue samples to verify its effectiveness as an ESG.
- 28 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (10) , 1442-1445
Improved Linearity and Efficiency of 5-GHz HBT Power Amplifier Using Transformer-Based Second Harmonic Trap Network
This letter presents an improved linear and efficient heterojunction bipolar transistor (HBT) power amplifier (PA) for mobile applications using a newly proposed transformer (TF)-based second harmonic trap that only terminates the second harmonic, without affecting the fundamental frequency. Compared to the configuration without the second harmonic trap, the PA with the proposed second harmonic trap has improved linearity, gain, and PAE. The PA is implemented in a 2- ${\mu }{\text{m}}$ InGaP/GaAs HBT process, and the input and output TFs are built on a nine-layer printed circuit board. The fabricated PA achieves a small-signal gain of 23.3 dB, saturated output power of 33.5 dBm, and peak PAE of 45.9% at a collector voltage of 4.5 V over 5.15–5.925 GHz under continuous-wave signal. A new radio (NR) 100-MHz QPSK CP 273 RB signal with a peak-to-average power ratio (PAPR) of 10.7 dB is used to test linearity. The PA achieves improved efficiency from 5.8%–9% to 6.4%–11.5% in the linear output power region which meeting adjacent channel leakage ratio (ACLR) of $-$ 33 dBc.
- 28 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (10) , 1442-1445
Improved Linearity and Efficiency of 5-GHz HBT Power Amplifier Using Transformer-Based Second Harmonic Trap Network
This letter presents an improved linear and efficient heterojunction bipolar transistor (HBT) power amplifier (PA) for mobile applications using a newly proposed transformer (TF)-based second harmonic trap that only terminates the second harmonic, without affecting the fundamental frequency. Compared to the configuration without the second harmonic trap, the PA with the proposed second harmonic trap has improved linearity, gain, and PAE. The PA is implemented in a 2- ${\mu }{\text{m}}$ InGaP/GaAs HBT process, and the input and output TFs are built on a nine-layer printed circuit board. The fabricated PA achieves a small-signal gain of 23.3 dB, saturated output power of 33.5 dBm, and peak PAE of 45.9% at a collector voltage of 4.5 V over 5.15–5.925 GHz under continuous-wave signal. A new radio (NR) 100-MHz QPSK CP 273 RB signal with a peak-to-average power ratio (PAPR) of 10.7 dB is used to test linearity. The PA achieves improved efficiency from 5.8%–9% to 6.4%–11.5% in the linear output power region which meeting adjacent channel leakage ratio (ACLR) of $-$ 33 dBc.
- 28 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (1) , 338-347
4 MHz Electrosurgical Generator System for Wide Load Impedance Range With SiC-Based Full-Bridge Inverter
A power conversion system to drive a high-frequency electrosurgical generator (ESG) is proposed. The proposed system consists of a 4-MHz full-bridge inverter capable of ensuring power in a wide load impedance range and implementing energy control functions in accordance with the ESG characteristics. Unlike conventional inverter systems, ESG cannot deliver energy directly to the load, but through an instrument, which makes it difficult to ensure power. Thus, impedance matching is essential to ensure power in ESG. For ensuring power, impedance matching is realized using a resonance filter while considering instrument induced parasitic components that cannot be ignored at high frequencies. The inverter is composed of silicon carbide suitable for the MHz switching operation. A prototype is to validate the proposed system. Experimental test of the prototype can provide a load power of more than 100 W for a tissue model with impedance range of 5–800 ${\bm{\Omega}}$ .
- 28 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (1) , 338-347
4 MHz Electrosurgical Generator System for Wide Load Impedance Range With SiC-Based Full-Bridge Inverter
A power conversion system to drive a high-frequency electrosurgical generator (ESG) is proposed. The proposed system consists of a 4-MHz full-bridge inverter capable of ensuring power in a wide load impedance range and implementing energy control functions in accordance with the ESG characteristics. Unlike conventional inverter systems, ESG cannot deliver energy directly to the load, but through an instrument, which makes it difficult to ensure power. Thus, impedance matching is essential to ensure power in ESG. For ensuring power, impedance matching is realized using a resonance filter while considering instrument induced parasitic components that cannot be ignored at high frequencies. The inverter is composed of silicon carbide suitable for the MHz switching operation. A prototype is to validate the proposed system. Experimental test of the prototype can provide a load power of more than 100 W for a tissue model with impedance range of 5–800 ${\bm{\Omega}}$ .
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (7) , 2934-2945
Switchless Dual-Power-Mode Fully Differential HBT Power Amplifier for Mobile Applications
This study proposes a switchless dual-power-mode (DPM) power amplifier (PA), which operates independently in high-powermode (HPM) and low-power mode (LPM) to improve the efficiency. The DPM PA optimizes the output impedances using bias control of the PA and the proposed bidirectional output matching structure with a transformer (TF) for each power mode with no switches for isolation between the LPM and the HPM with high passive efficiency. The proposed output structure realizes a high impedance in the nonoperating mode network to ensure that the operating mode network realizes the optimal impedance by utilizing bidirectional matching of the off characteristics of transistors and TF output for each mode. The differential DPM PA is implemented using a 2- $\mu \mathrm{m}$ InGaP/GaAs heterojunction bipolar transistor (HBT) process on a nine-layer printed circuit board with low insertion loss to demonstrate the proposed structure. The HPM and LPM, operating independently, achieved the gains of 24–25.5 and 11.4–12.9 dB and the saturated output power of 34.2–34.8 and 23.2–23.5 dBm, with a peak power-added efficiency (PAE) of 44.4%–49% and 32%–34.4%, respectively, under a continuous-wave (CW) signal test of over 5.15–5.925 GHz. The proposed PA error vector magnitude (EVM) is tested with 160 MHz of a 64-quadrature amplitude modulator (QAM) signal and achieves the average output powers of 24.5 and 14 dBm (EVM $=$ $ -$ 32 dB) and a PAE of 10.5% and 10.1% for HPM and LPM with digital predistortion, respectively.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (7) , 2934-2945
Switchless Dual-Power-Mode Fully Differential HBT Power Amplifier for Mobile Applications
This study proposes a switchless dual-power-mode (DPM) power amplifier (PA), which operates independently in high-powermode (HPM) and low-power mode (LPM) to improve the efficiency. The DPM PA optimizes the output impedances using bias control of the PA and the proposed bidirectional output matching structure with a transformer (TF) for each power mode with no switches for isolation between the LPM and the HPM with high passive efficiency. The proposed output structure realizes a high impedance in the nonoperating mode network to ensure that the operating mode network realizes the optimal impedance by utilizing bidirectional matching of the off characteristics of transistors and TF output for each mode. The differential DPM PA is implemented using a 2- $\mu \mathrm{m}$ InGaP/GaAs heterojunction bipolar transistor (HBT) process on a nine-layer printed circuit board with low insertion loss to demonstrate the proposed structure. The HPM and LPM, operating independently, achieved the gains of 24–25.5 and 11.4–12.9 dB and the saturated output power of 34.2–34.8 and 23.2–23.5 dBm, with a peak power-added efficiency (PAE) of 44.4%–49% and 32%–34.4%, respectively, under a continuous-wave (CW) signal test of over 5.15–5.925 GHz. The proposed PA error vector magnitude (EVM) is tested with 160 MHz of a 64-quadrature amplitude modulator (QAM) signal and achieves the average output powers of 24.5 and 14 dBm (EVM $=$ $ -$ 32 dB) and a PAE of 10.5% and 10.1% for HPM and LPM with digital predistortion, respectively.