Alexey Lysenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alexey Lysenko has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Elena Slyunko
Scientific Educational Center “Optical and Photonic Technologies”, National Research Tomsk State University, 634050 Tomsk, Russia
10 shared publications - Mikhail Zinoviev
Scientific Educational Center “Optical and Photonic Technologies”, National Research Tomsk State University, 634050 Tomsk, Russia
10 shared publications - Nikolai Nikolayevich Yudin
Scientific Educational Center “Optical and Photonic Technologies”, National Research Tomsk State University, 634050 Tomsk, Russia
10 shared publications - Sergey Podzyvalov
Scientific Educational Center “Optical and Photonic Technologies”, National Research Tomsk State University, 634050 Tomsk, Russia
10 shared publications - Vladimir S. Kuznetsov
Scientific Educational Center “Optical and Photonic Technologies”, National Research Tomsk State University, 634050 Tomsk, Russia
10 shared publications - Houssain Baalbaki
Scientific Educational Center “Optical and Photonic Technologies”, National Research Tomsk State University, 634050 Tomsk, Russia
9 shared publications
Latest Publications
- Open Access
- 28 May 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (11) , 4890
Minimization of Intrinsic Impurity Concentration in ZnGeP2 Single Crystals via Directional Recrystallization
Zinc germanium phosphide (ZnGeP2) is an important nonlinear crystal for mid-infrared conversion, but its performance is limited by residual absorption and intrinsic impurity phases. In this study, polycrystalline ZnGeP2 was synthesized by a modified two-temperature method, purified by inclined directional recrystallization for up to three cycles, and then grown into single crystals by the vertical Bridgman method. The resulting material was examined by shadow-projection imaging, transmission spectroscopy in the 650–2500 nm range, absorption measurements at 2.097 µm, laser-induced damage threshold (LIDT) testing, and powder X-ray diffraction. Repeated purification improved optical homogeneity and near-infrared transparency, while the absorption coefficient at 2.097 µm decreased from 0.45 to 0.30 cm−1 after three purification cycles. Semi-quantitative PXRD analysis showed progressive suppression of intrinsic impurity phosphides, with phase purity increasing from 86.31% after the first cycle to 95.995% after the second and reaching 100% after the third within the detection limit of the method. However, the LIDT decreased with increasing purification number, indicating a trade-off between lower optical losses and damage resistance. These results demonstrate that inclined directional recrystallization is an effective pre-growth purification route for ZnGeP2 and that the optimal number of purification cycles should be selected according to the intended application.
- 28 May 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (11) , 4890
Open AccessMinimization of Intrinsic Impurity Concentration in ZnGeP2 Single Crystals via Directional Recrystallization
Zinc germanium phosphide (ZnGeP2) is an important nonlinear crystal for mid-infrared conversion, but its performance is limited by residual absorption and intrinsic impurity phases. In this study, polycrystalline ZnGeP2 was synthesized by a modified two-temperature method, purified by inclined directional recrystallization for up to three cycles, and then grown into single crystals by the vertical Bridgman method. The resulting material was examined by shadow-projection imaging, transmission spectroscopy in the 650–2500 nm range, absorption measurements at 2.097 µm, laser-induced damage threshold (LIDT) testing, and powder X-ray diffraction. Repeated purification improved optical homogeneity and near-infrared transparency, while the absorption coefficient at 2.097 µm decreased from 0.45 to 0.30 cm−1 after three purification cycles. Semi-quantitative PXRD analysis showed progressive suppression of intrinsic impurity phosphides, with phase purity increasing from 86.31% after the first cycle to 95.995% after the second and reaching 100% after the third within the detection limit of the method. However, the LIDT decreased with increasing purification number, indicating a trade-off between lower optical losses and damage resistance. These results demonstrate that inclined directional recrystallization is an effective pre-growth purification route for ZnGeP2 and that the optimal number of purification cycles should be selected according to the intended application.
- 1 February 2026
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 93 (2) , 116-120
Technological control tools for roughness and defect structure of the surface of ZnGeP 2 single crystals using coherent optics methods
Subject of study. This study determines the surface-roughness parameters of polished infrared single-crystal materials by coherent-optics methods, using ZnGeP 2 single crystals as an example. Aim of study. The aim of this study is to develop a method for estimating the surface roughness of ZnGeP 2 zinc germanium phosphide crystals that can be integrated into the crystal-polishing process based on coherent-optics methods. Main results. A method for assessing the quality of crystal-surface finishing was developed using a spatial filter. An experimental setup was designed to evaluate the surface-polishing quality of ZnGeP 2 crystals. The intensity of the radiation scattered by surface roughness and reflected from the crystal surface was measured using a lens system and spatial filter that suppressed the dc component in the radiation spectrum. A 532 nm, 20 mW solid-state laser was used as the radiation source. The scattered-radiation intensity was measured with an FD-24K photodiode connected to a V7-40/5 universal voltmeter. Intensity values were measured for six crystal samples with different facet-processing qualities. Practical significance. The experimental data were verified using an industrial profilometer, confirming the applicability of the developed method to the qualitative assessment of the surface roughness of infrared optical materials, including the possibility of integrating this method into the polishing process.
- 1 February 2026
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 93 (2) , 116-120
Technological control tools for roughness and defect structure of the surface of ZnGeP 2 single crystals using coherent optics methods
Subject of study. This study determines the surface-roughness parameters of polished infrared single-crystal materials by coherent-optics methods, using ZnGeP 2 single crystals as an example. Aim of study. The aim of this study is to develop a method for estimating the surface roughness of ZnGeP 2 zinc germanium phosphide crystals that can be integrated into the crystal-polishing process based on coherent-optics methods. Main results. A method for assessing the quality of crystal-surface finishing was developed using a spatial filter. An experimental setup was designed to evaluate the surface-polishing quality of ZnGeP 2 crystals. The intensity of the radiation scattered by surface roughness and reflected from the crystal surface was measured using a lens system and spatial filter that suppressed the dc component in the radiation spectrum. A 532 nm, 20 mW solid-state laser was used as the radiation source. The scattered-radiation intensity was measured with an FD-24K photodiode connected to a V7-40/5 universal voltmeter. Intensity values were measured for six crystal samples with different facet-processing qualities. Practical significance. The experimental data were verified using an industrial profilometer, confirming the applicability of the developed method to the qualitative assessment of the surface roughness of infrared optical materials, including the possibility of integrating this method into the polishing process.
- Open Access
Band-like Inhomogeneity in Bulk ZnGeP2 Crystals, and Composition and Influence on Optical Properties
The influence of intrinsic impurities on the formation of band-like inhomogeneities in ZGP single crystals containing two highly volatile elements has been analyzed. It has been shown that the formation of growth bands occurs due to the accumulation of binary phosphides at the crystallization front and is accompanied by the formation of pores in the near-wall region of the ingot. A connection between near-wall pore formation and the presence of growth bands in ZGP has been established. X-ray spectrometry revealed differences in the chemical compositions of “light” and “dark” growth striations, with significant deviations from stoichiometry in these regions. The dark bands exhibited a higher phosphorus content compared to the light bands and showed an increased germanium content in the light bands. Differences in the orientation of crystallographic axes were observed between the light and dark regions. It has been shown that samples containing inclusions of band-like inhomogeneity significantly distort the profile of the radiation passing through and generated in the crystal and lead to pronounced astigmatism. However, in contrast to the extremely negative influence of banded inhomogeneity on the optical properties of single crystals, the influence of growth striations on the radiation resistance of crystals is minimal.
Open AccessBand-like Inhomogeneity in Bulk ZnGeP2 Crystals, and Composition and Influence on Optical Properties
The influence of intrinsic impurities on the formation of band-like inhomogeneities in ZGP single crystals containing two highly volatile elements has been analyzed. It has been shown that the formation of growth bands occurs due to the accumulation of binary phosphides at the crystallization front and is accompanied by the formation of pores in the near-wall region of the ingot. A connection between near-wall pore formation and the presence of growth bands in ZGP has been established. X-ray spectrometry revealed differences in the chemical compositions of “light” and “dark” growth striations, with significant deviations from stoichiometry in these regions. The dark bands exhibited a higher phosphorus content compared to the light bands and showed an increased germanium content in the light bands. Differences in the orientation of crystallographic axes were observed between the light and dark regions. It has been shown that samples containing inclusions of band-like inhomogeneity significantly distort the profile of the radiation passing through and generated in the crystal and lead to pronounced astigmatism. However, in contrast to the extremely negative influence of banded inhomogeneity on the optical properties of single crystals, the influence of growth striations on the radiation resistance of crystals is minimal.
- Open Access
Modification of the Spectral Absorption Characteristics of ZnGeP2 in the THz and IR Wavelength Ranges Due to Diffusion Doping with Impurity Atoms of Mg, Se, Sn, and Pb
This study demonstrates that diffusion doping of ZGP single crystals with impurity atoms (Mg, Se, Sn, Pb) leads to a decrease in the specific conductivity of the samples. Consequently, this results in reduced absorption in the terahertz frequency range (150–1000 μm). It has been shown that doping ZGP samples with selenium (Se) and lead (Pb) atoms reduces absorption in the infrared region from 0.3–0.6 cm−1 to 0.06–0.09 cm−1. Doping with tin (Sn) leads to a decrease in absorption only in the wavelength region near 2.1 μm from 0.2 cm−1 to 0.05 cm−1. The proposed mechanism for the decrease in infrared absorption is a reduction in zinc vacancies due to doping with impurity atoms. This research lays the groundwork for a technology that produces ZGP crystals with minimal absorption within the 2–8 μm wavelength range, eliminating the need for fast electron beam irradiation technology. This advancement will facilitate the fabrication of ZGP crystals with arbitrary apertures.
Open AccessModification of the Spectral Absorption Characteristics of ZnGeP2 in the THz and IR Wavelength Ranges Due to Diffusion Doping with Impurity Atoms of Mg, Se, Sn, and Pb
This study demonstrates that diffusion doping of ZGP single crystals with impurity atoms (Mg, Se, Sn, Pb) leads to a decrease in the specific conductivity of the samples. Consequently, this results in reduced absorption in the terahertz frequency range (150–1000 μm). It has been shown that doping ZGP samples with selenium (Se) and lead (Pb) atoms reduces absorption in the infrared region from 0.3–0.6 cm−1 to 0.06–0.09 cm−1. Doping with tin (Sn) leads to a decrease in absorption only in the wavelength region near 2.1 μm from 0.2 cm−1 to 0.05 cm−1. The proposed mechanism for the decrease in infrared absorption is a reduction in zinc vacancies due to doping with impurity atoms. This research lays the groundwork for a technology that produces ZGP crystals with minimal absorption within the 2–8 μm wavelength range, eliminating the need for fast electron beam irradiation technology. This advancement will facilitate the fabrication of ZGP crystals with arbitrary apertures.
- Open Access
Experimental Investigation of Laser Damage Limit for ZPG Infrared Single Crystal Using Deep Magnetorheological Polishing of Working Surfaces
Zinc germanium phosphide (ZGP) crystals have garnered significant attention for their nonlinear properties, making them good candidates for powerful mid-IR optical parametric oscillators and second-harmonic generators. A ZnGeP2 single crystal was treated by deep magnetorheological processing (MRP) until an Angstrom level of roughness. The studies presented in this article are devoted to the experimental evaluation of the influence of deep removal (up to 150 μm) from the surface of a ZnGeP2 single crystal by magnetorheological polishing on the parameters of optical breakdown. It was shown that the dependence of the ZnGeP2 laser-induced damage threshold on MRP depth is a smooth monotonically decreasing logarithmic function. The obtained logarithmic dependence indicates the thermal nature of optical breakdown and the dependence of the ZnGeP2 laser-induced damage threshold on the concentration of surface absorbing defects.
Open AccessExperimental Investigation of Laser Damage Limit for ZPG Infrared Single Crystal Using Deep Magnetorheological Polishing of Working Surfaces
Zinc germanium phosphide (ZGP) crystals have garnered significant attention for their nonlinear properties, making them good candidates for powerful mid-IR optical parametric oscillators and second-harmonic generators. A ZnGeP2 single crystal was treated by deep magnetorheological processing (MRP) until an Angstrom level of roughness. The studies presented in this article are devoted to the experimental evaluation of the influence of deep removal (up to 150 μm) from the surface of a ZnGeP2 single crystal by magnetorheological polishing on the parameters of optical breakdown. It was shown that the dependence of the ZnGeP2 laser-induced damage threshold on MRP depth is a smooth monotonically decreasing logarithmic function. The obtained logarithmic dependence indicates the thermal nature of optical breakdown and the dependence of the ZnGeP2 laser-induced damage threshold on the concentration of surface absorbing defects.
- Open Access
Physical and Technological Aspects of Laser-Induced Damage of ZGP Single Crystals under Periodically Pulsed Laser Irradiation at 2.1 μm
The nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their applications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes the mechanisms of the laser-induced damage (LID) of high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or the Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflective coatings on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold are also discussed. The impact of the test laser parameters on the LID threshold and the transient area near the LID threshold obtained using digital holography are analyzed. The influence of the pre-damage processes on the optical parametric oscillations is reported. Lastly, the prospects for improving ZGP crystals to further increase the LID threshold are discussed.
Open AccessPhysical and Technological Aspects of Laser-Induced Damage of ZGP Single Crystals under Periodically Pulsed Laser Irradiation at 2.1 μm
The nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their applications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes the mechanisms of the laser-induced damage (LID) of high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or the Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflective coatings on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold are also discussed. The impact of the test laser parameters on the LID threshold and the transient area near the LID threshold obtained using digital holography are analyzed. The influence of the pre-damage processes on the optical parametric oscillations is reported. Lastly, the prospects for improving ZGP crystals to further increase the LID threshold are discussed.
- Open Access
- 23 November 2023
- Published by MDPI AG in Preprints.org
Physical and Technological Aspects of Laser Induced Damage of ZGP Single Crystals under Periodically-Pulsed Laser Irradiation at 2.1 μm
Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.
- 23 November 2023
- Published by MDPI AG in Preprints.org
Open AccessPhysical and Technological Aspects of Laser Induced Damage of ZGP Single Crystals under Periodically-Pulsed Laser Irradiation at 2.1 μm
Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.
- Open Access
Effect of UV and IR Radiation on the Electrical Characteristics of Ga2O3/ZnGeP2 Hetero-Structures
The data on electrical and photoelectric characteristics of Ga2O3/ZnGeP2 hetero-structures formed by RF magnetron sputtering Ga2O3 target with a purity of (99.99%) were obtained. The samples are sensitive to UV radiation with a wavelength of λ = 254 nm and are able to work offline as detectors of short-wave radiation. Structures with Ga2O3 film that was not annealed at 400 °C show weak sensitivity to long-wavelength radiation, including white light and near-IR (λ = 808 and 1064 nm). After annealing in an air environment (400 °C, 30 min), ZnGeP2 crystals in contact with Ga2O3 show n-type conductivity semiconductor properties, the sensitivity of Ga2O3/ZnGeP2 hetero-structures increases in the UV and IR ranges; the photovoltaic effect is preserved. Under λ = 254 nm illumination, the open-circuit voltage is fixed at positive potentials on the electrode to Ga2O3, the short-circuit current increases by three orders of magnitude, and the responsivity increases by an order of magnitude. The structures detect the photovoltaic effect in the near-IR range and are able to work offline (remotely) as detectors of long-wavelength radiation.
Open AccessEffect of UV and IR Radiation on the Electrical Characteristics of Ga2O3/ZnGeP2 Hetero-Structures
The data on electrical and photoelectric characteristics of Ga2O3/ZnGeP2 hetero-structures formed by RF magnetron sputtering Ga2O3 target with a purity of (99.99%) were obtained. The samples are sensitive to UV radiation with a wavelength of λ = 254 nm and are able to work offline as detectors of short-wave radiation. Structures with Ga2O3 film that was not annealed at 400 °C show weak sensitivity to long-wavelength radiation, including white light and near-IR (λ = 808 and 1064 nm). After annealing in an air environment (400 °C, 30 min), ZnGeP2 crystals in contact with Ga2O3 show n-type conductivity semiconductor properties, the sensitivity of Ga2O3/ZnGeP2 hetero-structures increases in the UV and IR ranges; the photovoltaic effect is preserved. Under λ = 254 nm illumination, the open-circuit voltage is fixed at positive potentials on the electrode to Ga2O3, the short-circuit current increases by three orders of magnitude, and the responsivity increases by an order of magnitude. The structures detect the photovoltaic effect in the near-IR range and are able to work offline (remotely) as detectors of long-wavelength radiation.
- Open Access
Effect of Dopants on Laser-Induced Damage Threshold of ZnGeP2
The effect of doping Mg, Se, and Ca by diffusion into ZnGeP2 on the optical damage threshold at a wavelength of 2.1 μm has been studied. It has been shown that diffusion-doping with Mg and Se leads to an increase in the laser-induced damage threshold (LIDT) of a single crystal (monocrystal), ZnGeP2; upon annealing at a temperature of 750 °C, the damage threshold of samples doped with Mg and Se increases by 31% and 21% from 2.2 ± 0.1 J/cm2 to 2.9 ± 0.1 and 2.7 ± 0.1 J/cm2, respectively. When ZnGeP2 is doped with Ca, the opposite trend is observed. It has been suggested that the changes in the LIDT depending on the introduced impurity by diffusion can be explained by the creation of additional energy dissipation channels due to the processes of radiative and fast non-radiative relaxation through impurity energy levels, which further requires experimental confirmation.
Open AccessEffect of Dopants on Laser-Induced Damage Threshold of ZnGeP2
The effect of doping Mg, Se, and Ca by diffusion into ZnGeP2 on the optical damage threshold at a wavelength of 2.1 μm has been studied. It has been shown that diffusion-doping with Mg and Se leads to an increase in the laser-induced damage threshold (LIDT) of a single crystal (monocrystal), ZnGeP2; upon annealing at a temperature of 750 °C, the damage threshold of samples doped with Mg and Se increases by 31% and 21% from 2.2 ± 0.1 J/cm2 to 2.9 ± 0.1 and 2.7 ± 0.1 J/cm2, respectively. When ZnGeP2 is doped with Ca, the opposite trend is observed. It has been suggested that the changes in the LIDT depending on the introduced impurity by diffusion can be explained by the creation of additional energy dissipation channels due to the processes of radiative and fast non-radiative relaxation through impurity energy levels, which further requires experimental confirmation.
- Open Access
High-Strength Optical Coatings for Single-Crystal ZnGeP2 by the IBS Method Using Selenide and Oxide Materials
The paper presents the results on the development of an optical coating for a single-crystal ZnGeP2 substrate based on a selenide-oxide pair of materials (ZnSe/Al2O3). The obtained coating ensures the operation of OPO in the mid-IR range up to 5 μm wavelengths. The possibility of ZnSe sputtering by the IBS method is shown. The obtained optical coating has a high laser-induced damage threshold (LIDT) value at a 2097 µm wavelength: J/cm2 in energy density and = 101 W/cm2 in power density at a 10 KHz pulse repetition frequency and a pulse duration of 35 ns. Thus, it is shown for the first time that the pair of materials ZnSe/Al2O3 can be used for the deposition of optical coatings by the IBS method with high LIDT values for ZnGeP2 optical elements operating in the mid-IR range.Open AccessHigh-Strength Optical Coatings for Single-Crystal ZnGeP2 by the IBS Method Using Selenide and Oxide Materials
The paper presents the results on the development of an optical coating for a single-crystal ZnGeP2 substrate based on a selenide-oxide pair of materials (ZnSe/Al2O3). The obtained coating ensures the operation of OPO in the mid-IR range up to 5 μm wavelengths. The possibility of ZnSe sputtering by the IBS method is shown. The obtained optical coating has a high laser-induced damage threshold (LIDT) value at a 2097 µm wavelength: J/cm2 in energy density and = 101 W/cm2 in power density at a 10 KHz pulse repetition frequency and a pulse duration of 35 ns. Thus, it is shown for the first time that the pair of materials ZnSe/Al2O3 can be used for the deposition of optical coatings by the IBS method with high LIDT values for ZnGeP2 optical elements operating in the mid-IR range.