Roman Sajzew
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Roman Sajzew has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Lothar Wondraczek
Otto Schott Institute of Materials Research University of Jena Jena Germany
7 shared publications - Alexander Knebel
Otto Schott Institute of Materials Research, Friedrich Schiller University Jena, Jena, Germany
5 shared publications - Oksana Smirnova
Friedrich Schiller University Jena
4 shared publications - David A. Keen
ISIS Facility, Rutherford Appleton Laboratory, Harwell Campus, Didcot, Oxfordshire OX11 0QX, UK
3 shared publications Georgina Robertson
University of Cambridge
3 shared publications- Thomas Douglas Bennett
MacDiarmid Institute for Advanced Materials and Nanotechnology, School of Physical and Chemical Sciences, University of Canterbury, Christchurch, New Zealand
3 shared publications
Latest Publications
- Open Access
- 10 June 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Unlocking Large-Area Free-Standing MOF-Glasses for Molecular Sieving Gas Separation Membranes
Membranes prepared of MOF glasses holds significant promise for gas separations due to the absence of grain boundary diffusion, liquid processibility, and tunability. However, the inherent high viscosity of MOF melts renders them prone to cracking upon rapid cooling and further handling, and their propensity to densify at high temperatures and long time in molten state severely limits their upscaling possibilities. Here, we present a solution to overcome these limitations and demonstrate that - by selecting suitable materials particularly fitting thermal and mechanical behavior to those of MOF-glass – it is possible to process large, crack-free MOF-glass sheets. By carefully optimizing each step of the process – from melting to performance testing – we successfully fabricate a crack-free, self-supported ZIF-62 glass membrane from pristine ZIF-62 crystals. The microstructure is investigated using microscopy as well as SEM-EDX analysis, confirming homogeneous boundary-free MOF-glass, while gas permeation experiments are carried out to prove the applicability of MOF-glass as gas separation membrane. The membrane exhibits exceptionally sharp methane molecular sieving cut-off with such low permeability that gas chromatography is unable to detect CH4. We conclude this work by giving a brief outlook of the remaining challenges and perspectives for MOF glasses in a view of gas separation membranes.
- 10 June 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessUnlocking Large-Area Free-Standing MOF-Glasses for Molecular Sieving Gas Separation Membranes
Membranes prepared of MOF glasses holds significant promise for gas separations due to the absence of grain boundary diffusion, liquid processibility, and tunability. However, the inherent high viscosity of MOF melts renders them prone to cracking upon rapid cooling and further handling, and their propensity to densify at high temperatures and long time in molten state severely limits their upscaling possibilities. Here, we present a solution to overcome these limitations and demonstrate that - by selecting suitable materials particularly fitting thermal and mechanical behavior to those of MOF-glass – it is possible to process large, crack-free MOF-glass sheets. By carefully optimizing each step of the process – from melting to performance testing – we successfully fabricate a crack-free, self-supported ZIF-62 glass membrane from pristine ZIF-62 crystals. The microstructure is investigated using microscopy as well as SEM-EDX analysis, confirming homogeneous boundary-free MOF-glass, while gas permeation experiments are carried out to prove the applicability of MOF-glass as gas separation membrane. The membrane exhibits exceptionally sharp methane molecular sieving cut-off with such low permeability that gas chromatography is unable to detect CH4. We conclude this work by giving a brief outlook of the remaining challenges and perspectives for MOF glasses in a view of gas separation membranes.
- Open Access
- 30 January 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Observation of a reversible order-order transition in a metal-organic framework – ionic liquid nanocomposite phase change material
Composites composed of ionic liquids (ILs) and metal-organic framework (MOF) materials have been proposed for a range of potential applications, including gas separation, ion conduction, and hybrid glass formation. Here, we discover an order transition in an IL@MOF composite using the commodity compounds CuBTC (copper benzene-1,3,5-tricarboxylate) and EMIMTFSI (1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide). This transition absent for the bare MOF or IL provides an extended super-cooling range for latent heat storage at a capacity similar to that of soft paraffins, in the temperature range of ~ 220 C. Structural analysis and in situ monitoring indicate electrostatic interaction of the IL molecules with the Cu paddle-wheels, leading to a decrease in pore symmetry at low temperature. These interactions are released above the transition temperature, what reflects in a reversible volume expansion of the MOF composite on the order of 1 %.
- 30 January 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessObservation of a reversible order-order transition in a metal-organic framework – ionic liquid nanocomposite phase change material
Composites composed of ionic liquids (ILs) and metal-organic framework (MOF) materials have been proposed for a range of potential applications, including gas separation, ion conduction, and hybrid glass formation. Here, we discover an order transition in an IL@MOF composite using the commodity compounds CuBTC (copper benzene-1,3,5-tricarboxylate) and EMIMTFSI (1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide). This transition absent for the bare MOF or IL provides an extended super-cooling range for latent heat storage at a capacity similar to that of soft paraffins, in the temperature range of ~ 220 C. Structural analysis and in situ monitoring indicate electrostatic interaction of the IL molecules with the Cu paddle-wheels, leading to a decrease in pore symmetry at low temperature. These interactions are released above the transition temperature, what reflects in a reversible volume expansion of the MOF composite on the order of 1 %.
- Open Access
- 25 December 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Micro-optical elements from optical-quality ZIF-62 hybrid glasses by hot-imprinting
Hybrid glasses derived from meltable metal-organic frameworks (MOFs) promise to combine the intriguing properties of MOFs with the universal processing ability of glasses. However, shaping of hybrid glasses in their liquid state has been elusive thus far. Here, we present optical-quality glasses derived from the zeolitic imidazole framework ZIF-62 in the form of cm-scale objects. These allow for in-depth studies of optical transparency and refraction across the ultraviolet to near-infrared spectral range. Fundamental viscosity data are reported using a ball penetration technique, and subsequently used to demonstrate the fabrication of micro-optical devices by thermal imprinting. Using 3D printed fused silica templates, we show that concave as well as convex structures can be obtained at high precision by remelting the glass without trading-off on material quality. This paves a route towards melt-processing of MOF-derived glasses on a scale relevant for real-world applications and enables multifunctional micro-optical devices combining the gas uptake and permeation ability of MOFs with the optical functionality of a glass.
- 25 December 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessMicro-optical elements from optical-quality ZIF-62 hybrid glasses by hot-imprinting
Hybrid glasses derived from meltable metal-organic frameworks (MOFs) promise to combine the intriguing properties of MOFs with the universal processing ability of glasses. However, shaping of hybrid glasses in their liquid state has been elusive thus far. Here, we present optical-quality glasses derived from the zeolitic imidazole framework ZIF-62 in the form of cm-scale objects. These allow for in-depth studies of optical transparency and refraction across the ultraviolet to near-infrared spectral range. Fundamental viscosity data are reported using a ball penetration technique, and subsequently used to demonstrate the fabrication of micro-optical devices by thermal imprinting. Using 3D printed fused silica templates, we show that concave as well as convex structures can be obtained at high precision by remelting the glass without trading-off on material quality. This paves a route towards melt-processing of MOF-derived glasses on a scale relevant for real-world applications and enables multifunctional micro-optical devices combining the gas uptake and permeation ability of MOFs with the optical functionality of a glass.
- Open Access
- 4 September 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Gas Separating Metal-Organic Framework Membrane Films on Large Area 3D-Printed Tubular Ceramic Scaffolds
Polycrystalline metal-organic framework (MOF) membrane films prepared on ceramic supports can separate gases with high energy efficiency. They generally exhibit very high permeance and selectivity but suffer from cost issues through the required ceramic supports. Increasing the area and reducing the ceramic component to a minimum could be a strategy to enabling neat membrane of MOFs. In a rapid prototyping approach using 3D-printed porous scaffolds with a double helical channel geometry, we dramatically increase the active membrane area-to-volume ratio. Following stereolithographic printing and de-binding of a ceramic slurry, an adapted sintering protocol was employed to sinter commercially available alumina slurries into porous scaffolds. The 3D-printed scaffolds were optimized at a porosity of 40%, with satisfying mechanical stability. Furthermore, synthetic procedures yielding omnidirectional, homogeneous coatings on the outside and inside of the tubular scaffolds were developed. Membrane films of ZIF-8 and HKUST-1 covering a huge 50 cm² membrane area were produced in this way by applying a counter-diffusion methodology. Gas separation performance was evaluated for H2, CO2, N2 and CH4, in single-gas measurements and on their binary gas mixtures.
- 4 September 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessGas Separating Metal-Organic Framework Membrane Films on Large Area 3D-Printed Tubular Ceramic Scaffolds
Polycrystalline metal-organic framework (MOF) membrane films prepared on ceramic supports can separate gases with high energy efficiency. They generally exhibit very high permeance and selectivity but suffer from cost issues through the required ceramic supports. Increasing the area and reducing the ceramic component to a minimum could be a strategy to enabling neat membrane of MOFs. In a rapid prototyping approach using 3D-printed porous scaffolds with a double helical channel geometry, we dramatically increase the active membrane area-to-volume ratio. Following stereolithographic printing and de-binding of a ceramic slurry, an adapted sintering protocol was employed to sinter commercially available alumina slurries into porous scaffolds. The 3D-printed scaffolds were optimized at a porosity of 40%, with satisfying mechanical stability. Furthermore, synthetic procedures yielding omnidirectional, homogeneous coatings on the outside and inside of the tubular scaffolds were developed. Membrane films of ZIF-8 and HKUST-1 covering a huge 50 cm² membrane area were produced in this way by applying a counter-diffusion methodology. Gas separation performance was evaluated for H2, CO2, N2 and CH4, in single-gas measurements and on their binary gas mixtures.
- Open Access
- 8 May 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Synthesis and characterisation of metal-organic framework-inorganic glass hybrid blends
Recently, increased attention has been focused on amorphous metal-organic frameworks (MOFs) and, more specifically, MOF glasses, the first new glass category discovered since the 1970s. In this work, we explore the fabrication of a compositional series of hybrid blends that combine ZIF-62(Zn) glass and an inorganic glass, 30Na2O-70P2O5, in an effort to combine the chemical versatility of the MOF glass with the mechanical properties of the inorganic glass. We investigate the interfacial interactions between the two components using pair distribution function analysis and solid state NMR spectroscopy, and suggest potential interactions between the two phases. Thermal analysis of the blend samples indicated that they were less thermally stable than the starting materials, and had a Tg shifted relative to the pristine materials. Annular dark field scanning transmission electron microscopy, X-ray energy dispersive spectroscopy (EDS), nanoindentation and 31P NMR all indicated close mixing of the two phases, suggesting that immiscible blends had formed.
- 8 May 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessSynthesis and characterisation of metal-organic framework-inorganic glass hybrid blends
Recently, increased attention has been focused on amorphous metal-organic frameworks (MOFs) and, more specifically, MOF glasses, the first new glass category discovered since the 1970s. In this work, we explore the fabrication of a compositional series of hybrid blends that combine ZIF-62(Zn) glass and an inorganic glass, 30Na2O-70P2O5, in an effort to combine the chemical versatility of the MOF glass with the mechanical properties of the inorganic glass. We investigate the interfacial interactions between the two components using pair distribution function analysis and solid state NMR spectroscopy, and suggest potential interactions between the two phases. Thermal analysis of the blend samples indicated that they were less thermally stable than the starting materials, and had a Tg shifted relative to the pristine materials. Annular dark field scanning transmission electron microscopy, X-ray energy dispersive spectroscopy (EDS), nanoindentation and 31P NMR all indicated close mixing of the two phases, suggesting that immiscible blends had formed.
- Open Access
- 25 April 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Interfacial bonding between a crystalline metal-organic framework and an inorganic glass
The interface within a composite is critically important for the chemical and physical properties of these materials. However, experimental structural studies of the interfacial regions within metal-organic framework (MOF) composites are extremely challenging. Here, we provide the first example of a new MOF composite family, i.e. using an inorganic glass matrix host in place of the commonly used organic polymers. Crucially, we also decipher atom-atom interactions at the interface. Specifically, we dispersed ZIF-8 within a phosphate glass matrix, and identified interactions at the interface using several different analysis methods of pair distribution function (PDF) and multinuclear multidimensional magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy. These demonstrated glass-ZIF atom-atom correlations. Additionally, carbon dioxide uptake and stability tests were also performed to check the increment of the surface area and the stability and durability of the material in different media. This opens up the possibility to create new composites including the intrinsic chemical properties of the constituent MOFs and inorganic glasses.
- 25 April 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessInterfacial bonding between a crystalline metal-organic framework and an inorganic glass
The interface within a composite is critically important for the chemical and physical properties of these materials. However, experimental structural studies of the interfacial regions within metal-organic framework (MOF) composites are extremely challenging. Here, we provide the first example of a new MOF composite family, i.e. using an inorganic glass matrix host in place of the commonly used organic polymers. Crucially, we also decipher atom-atom interactions at the interface. Specifically, we dispersed ZIF-8 within a phosphate glass matrix, and identified interactions at the interface using several different analysis methods of pair distribution function (PDF) and multinuclear multidimensional magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy. These demonstrated glass-ZIF atom-atom correlations. Additionally, carbon dioxide uptake and stability tests were also performed to check the increment of the surface area and the stability and durability of the material in different media. This opens up the possibility to create new composites including the intrinsic chemical properties of the constituent MOFs and inorganic glasses.
- Open Access
- 12 February 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Precise control over gas transporting channels in zeolitic imidazolate framework glasses
Porous materials, such as metal-organic frameworks emerge to solve important quests of our modern society, such as CO2 sequestration. Zeolitic Imidazolate Frameworks (ZIFs) can undergo a glass transition to form ZIF-glasses; they combine the liquid handling of classical glasses with tremendous potential for gas separations. Using millimeter-sized ZIF-62 single crystals and centimeter-sized ZIF-62-glass we demonstrate scalability and processability. Further, following the evolution of gas penetration into ZIF-crystals and ZIF-glasses by IR microimaging techniques enables to determine diffusion constants and changes to the pore architecture on the Angstrom-scale. The evolution of ZIF-glasses is observed in situ using a microscope heating stage. The pore-collapse during glass-processing is tracked by changes to density and volume of the glasses. Mass spectrometry investigates the crystal-to-glass transition and thermal processing ability.
- 12 February 2023
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessPrecise control over gas transporting channels in zeolitic imidazolate framework glasses
Porous materials, such as metal-organic frameworks emerge to solve important quests of our modern society, such as CO2 sequestration. Zeolitic Imidazolate Frameworks (ZIFs) can undergo a glass transition to form ZIF-glasses; they combine the liquid handling of classical glasses with tremendous potential for gas separations. Using millimeter-sized ZIF-62 single crystals and centimeter-sized ZIF-62-glass we demonstrate scalability and processability. Further, following the evolution of gas penetration into ZIF-crystals and ZIF-glasses by IR microimaging techniques enables to determine diffusion constants and changes to the pore architecture on the Angstrom-scale. The evolution of ZIF-glasses is observed in situ using a microscope heating stage. The pore-collapse during glass-processing is tracked by changes to density and volume of the glasses. Mass spectrometry investigates the crystal-to-glass transition and thermal processing ability.