MYMei Yang

Mei Yang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mei Yang has a total of 62 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical investigation on rock-breaking performance and arrangement optimization of disc cutter with miniature spherical inserts

    by Shijun Chu, Huizhen Chai, Wei Zhang, Lei Jiang, Haibin Liu, Mei Yang

    The cutter with insert teeth is a critical tool for TBM rock-breaking and has been widely applied in transportation and mining tunnel construction. The arrangement of insert teeth is a key factor influencing rock-breaking performance and load characteristics. However, conventional large-insert designs suffer from stress concentration and severe tooth failure in hard rock conditions, necessitating a new approach to tooth arrangement. To address this issue, this paper investigates the rock-breaking performance of disc cutters with miniature spherical inserts (CST). A three-dimensional numerical model for CST rock-breaking was established using the finite element method and validated against linear cutting experiments. Using this model, the influence of three insert arrangement patterns (three-row staggered, two-row symmetrical, and two-row staggered) on rock fragmentation performance was systematically analyzed, followed by a parametric study on the coupled effects of insert height (2.5–4 mm) and tooth count (120–192). The results show that the three-row staggered arrangement achieves the largest rock-breaking volume (1721 mm 3 ) and the lowest vertical force (44.1 kN) among the tested configurations, while the two-row staggered arrangement exhibits the lowest specific energy (263.6 J/mm 3 ) and the smallest rolling force (2.23 kN). For the granite investigated (UCS = 105.25 MPa) under the present test conditions (penetration depth of 5 mm, tooth count of 120–192), the insert height of 3 mm yields the lowest specific energy. The research findings reveal the influence patterns of insert arrangement and structural parameters on rock-breaking performance, providing a theoretical basis for the structural optimization and engineering application of cutters with inserted miniature spherical teeth.

  • Open Access

    Comparative analysis of tunneling performance for conventional and atmospheric cutterhead under similar geological conditions: A case study of the Haizhuwan tunnel project

    by Peng Chen, Yimin Xia, Qingyang Wang, Zhe Zhang, Shuhua Huang, Mei Yang

    Cutterhead is the core component of the tunnel boring machine (TBM). In slurry TBM engineering, conventional and atmospheric cutterheads are usually associated with different cutterhead structure, cutter change mode and auxiliary system configurations, which may lead to different responses under complex geological conditions. To explore the tunneling performance and differences, this study presents a comparative field case analysis of two slurry TBM system configurations featuring conventional and atmospheric cutterheads in the parallel tunnels of the Haizhuwan Tunnel Project. First, the tunneling performance under four representative geological conditions was analyzed based on tunneling data, equipment modifications, and cutter failure characteristics. Subsequently, the Kruskal-Wallis test was used to compare the tunneling differences between the two machine configurations, with tunneling time per ring and construction time per ring taken as the main evaluation indicators. The results show that, under the investigated project conditions, in challenging environments, such as soft soil strata with poor formation stability, the atmospheric cutterhead configured system demonstrates better tunneling performance. In contrast, in hard rock strata, particularly under high rock hardness conditions, conventional cutterhead configured system exhibits superior tunneling performance. These findings provide practical engineering reference for slurry TBM equipment configuration and construction organization under similar geological conditions.

  • Open Access

    Comparative study on the cutting performance of super-large diameter atmospheric cutterhead and pressurized cutterhead under the same stratum

    by Peng Chen, Shuhua Huang, Jicheng Shu, Ji Liu, Jian Sheng, Laikuang Lin, Mei Yang

    The difference in cutter arrangement between the atmospheric cutterhead and the pressurized cutterhead leads to a significant difference in the cutting performance of the two cutterheads. Due to the lack of quantitative comparison and analysis of the cutting performance, the selection of cutterheads lacks a quantitative and scientific basis. In this paper, an atmospheric cutterhead and a pressurized cutterhead with 15.07 m diameters are taken as the research objects, which were excavated in the same slightly weathered argillaceous siltstone strata for a certain tunnel project in Guangzhou. Rotary cutting rock simulations of cutter groups in the central area, front area and edge area of the two cutterheads are established, where the rock damage form, load characteristics and specific energy of the three areas of the two cutterheads are comparatively analyzed. Furthermore, the actual engineering tunneling performance of the two cutterheads was analyzed to verify the simulation results. The vertical force and rolling force of each disc cutter on the pressurized cutterhead are 75.7% and 78.2% of those on the atmospheric cutterhead, respectively, where the cutter spacing of the pressurized cutterhead is smaller. The rock-breaking specific energy of the cutter group in each area of the pressurized cutterhead is 95.6–73.4% of that of the atmospheric cutterhead. Meanwhile, the total thrust and torque of the pressurized cutterhead are 111.4% and 115.2% of those of the atmospheric cutterhead, respectively, where the pressurized cutterhead is equipped with more cutters. Therefore, the overall cutting performance of the pressurized cutterhead is better than that of the atmospheric cutterhead in slightly weathered argillaceous siltstone strata. This study provides a quantitative comparison method for the atmospheric cutterhead and the pressurized cutterhead under the same geological conditions, which can be extended to the structure selection of large-diameter cutterheads of shield machines under other geological conditions.


  • Open Access

    Simulation study of rock-breaking performance of TBM cone-shape cutterhead under different tunneling parameters in spiral tunnel

    by Laikuang Lin, Ke Liu, Zhiyong Ji, Mengxue Qi, Ju Wang, Jing Xiao, Yimin Xia, Mei Yang

    Compared with plane cutterhead, the cone-shape cutterhead has better rock-breaking performance with a free surface during the rock-breaking process. Tunneling parameters of cone-shaped cutterhead have great influence on the rock-breaking efficiency and cutterhead thrust. A full-scale excavation model of cone-shape cutterhead was constructed using LS-DYNA to characterize the rock-breaking process accurately and efficiently. The effects of penetration depth and rotation speed on the damage, cutterhead thrust, and rock-breaking efficiency in each area were investigated. The results show that the penetration depth is more sensitive to the field penetration index and thrust fluctuation index than the rotation speed. When the penetration depth and rotation speed is 4 mm/r and 4.5 r/min, respectively, the cone-shape cutterhead performs best with high rock-breaking efficiency and smallest fluctuation of cutterhead thrust under specific geological conditions. It provides suggestions for the selection of tunneling parameters during cone-shape cutterhead construction.

  • Open Access

    Vibration signal characteristics research of rock breaking by cutter under different rock types and cutting parameters

    by Bowen Zhang, Guowei Feng, Mei Yang, Chuanzheng Geng, Bo Wu

    In the process of tunnel excavation, the vibration characteristic during cutter breaking rock process is the key factor affecting the TBM tunneling efficiency and cutter life. Therefore, it is necessary to investigate the vibration characteristics of the cutter while breaking different rock types. A series of full-scale cutter-breaking-rock experiments are conducted cutting red sandstone, granite, and limestone, where the vibration signals are monitored. And time-domain frequency-domain and time–frequency analyses were proposed to reveal the differences in signal characteristics generated by different kinds of rock, where Fast Fourier Transform (FFT) and VMD are used to distinguish the vibration signal. The frequency spectral structure of red sandstone, granite, and limestone are mainly distributed in the range of 0–500, 0–700, and 0–700 Hz, respectively. The central frequency of vibration energy distribution of red sandstone, granite, and limestone is 283.88, 478.14, and 567.36 Hz, respectively. The central frequency of vibration energy distribution for cutters can be regarded as an important distinguishable features of rock types, which may be promising for lithological recognition during TBM construction. It can provide accurate geology information for TBM worker to adjust the tunneling parameters promptly, making contribution for TBM efficient tunneling and reliable service.


  • Open Access

    Research on Vibration Characteristics in Waterjet Kerf‐Cutter Coupled Rock‐Breaking Method

    by Bo-Wen Zhang, Guo-Wei Feng, Wang Chen, Feng-Wei Yang, Chuan-Zheng Geng, Mei Yang, Jie Fu

    In order to reveal the effects of different kerf modes and the kerf depths on the vibration characteristics of the cutter system during the waterjet kerf‐cutter coupled rock‐breaking process, in this paper, a full‐size rock‐breaking test is carried out under the complete cutting mode (CD), different trajectory mode (DM), same trajectory mode (SM), triple‐kerf mode (TM), and the different kerf depths. The vibration signal characteristics of the cutter system, the ability of vibration reduction, and rock‐breaking mass are deeply analyzed. Furthermore, specific vibration (SV) and specific energy (SE) are combined to evaluate the performance of the waterjet kerf‐cutter coupled rock‐breaking method. The results show that the optimal kerf depth is 6 mm for the different kerf modes. When the kerf depth is 6 mm, the comprehensive rock‐breaking ability ranking is DM > TM > SM. The result provides new inspiration for the arrangement of waterjet nozzles on the cutterhead and the design of the high‐pressure waterjet rock‐breaking TBM.