Satoshi Yamasaki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Satoshi Yamasaki has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
- Hiromitsu Kato
Quantum Information Research Center, Institute of Advanced Sciences, Yokohama National University, Hodogaya, Japan
5 shared publications - Tetsuji Yasuda
National Institute of Advanced Industrial Science and Technology (AIST) 2 , Tsukuba, Ibaraki 305-8562, Japan
4 shared publications - Toshiharu Makino
Advanced Power Electronics Research Center, AIST, 1-1-1 Umezono, Tsukuba, Ibaraki, 305-8568, Japan
4 shared publications - Masahiko Ogura
National Institute of Advanced Industrial Science and Technology
3 shared publications - Norio Tokuda
Nanomaterials Research Institute, Kanazawa University 3 , Kanazawa, Ishikawa 920-1192
3 shared publications Masayasu Nishizawa
Joint Research Center for Atom Technology (JRCAT), National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba 305-8562, Japan
2 shared publications
Latest Publications
- Open Access
- 13 February 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (7) , 072101
Electroluminescence of negatively charged single NV centers in diamond
The realization of electroluminescence (EL) of negatively charged nitrogen vacancy (NV−) centers is important toward all-electrical control of diamond quantum devices. In this study, we demonstrated electrical excitation and detection of EL of single NV− centers by using lateral diamond p+–i(n−)–n+ diodes. It had been grown by homoepitaxy using the plasma enhanced chemical vapor deposition technique. We introduced a lightly phosphorus doped i(n−) layer to stabilize the negative state of NV centers. It was estimated that the efficiency of the electrical excitation rate of the NV center was more than 30 times enhanced by introducing lateral diamond p+–i(n−)–n+ diodes structure compared with the previous vertical diode. Furthermore, the EL of a single NV− center embedded in the i(n−) layer region was characterized. The results show that the charge state of the single NV centers can be manipulated by the voltage applied to the p+–i(n−)–n+ diode, where the emission of EL is increasingly dominated by NV− in the range of 30 to 50 V.
- 13 February 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (7) , 072101
Open AccessElectroluminescence of negatively charged single NV centers in diamond
The realization of electroluminescence (EL) of negatively charged nitrogen vacancy (NV−) centers is important toward all-electrical control of diamond quantum devices. In this study, we demonstrated electrical excitation and detection of EL of single NV− centers by using lateral diamond p+–i(n−)–n+ diodes. It had been grown by homoepitaxy using the plasma enhanced chemical vapor deposition technique. We introduced a lightly phosphorus doped i(n−) layer to stabilize the negative state of NV centers. It was estimated that the efficiency of the electrical excitation rate of the NV center was more than 30 times enhanced by introducing lateral diamond p+–i(n−)–n+ diodes structure compared with the previous vertical diode. Furthermore, the EL of a single NV− center embedded in the i(n−) layer region was characterized. The results show that the charge state of the single NV centers can be manipulated by the voltage applied to the p+–i(n−)–n+ diode, where the emission of EL is increasingly dominated by NV− in the range of 30 to 50 V.
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 743-746
High Temperature Reliability Assessment and Degradation Analysis for Diamond Semiconductor Devices
The long-term reliability of Schottky pn diodes (SPNDs) on diamond having widely used Ti/Pt/Au electrodes was investigated at 500°C in order to identify degradation phenomena at higher temperatures. A vital degradation event was observed after the passage of about 100 hours in that both forward and reverse currents were progressively reduced. AES depth profiling and X-STEM-EELS analyses revealed that this occurred because the Ti contact material changed to insulating (or semiconductive) TiO2, causing large series resistance.
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 743-746
High Temperature Reliability Assessment and Degradation Analysis for Diamond Semiconductor Devices
The long-term reliability of Schottky pn diodes (SPNDs) on diamond having widely used Ti/Pt/Au electrodes was investigated at 500°C in order to identify degradation phenomena at higher temperatures. A vital degradation event was observed after the passage of about 100 hours in that both forward and reverse currents were progressively reduced. AES depth profiling and X-STEM-EELS analyses revealed that this occurred because the Ti contact material changed to insulating (or semiconductive) TiO2, causing large series resistance.
- 2 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 23 (4) , 1-8
Optically Driven Terahertz Wave Modulator Using Ring-Shaped Microstripline With GaInAs Photoconductive Mesa Structure
To improve wireless communications systems, it is desirable to seamlessly combine fiber-based optical and terahertz wireless communications systems. In this paper, we demonstrate a waveguide optically driven terahertz wave modulator using a ring-shaped microstripline with a GaInAs photoconductive mesa structure. In this device, terahertz wave modulation is performed by controlling the photo-generated carriers in the GaInAs mesa. As a result, a maximum extinction ratio of 16.8 dB in the terahertz band was obtained with a light irradiation of 15 dBm (32 mW), and the 3 dB modulation bandwidth was approximately 170 MHz.
- 2 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 23 (4) , 1-8
Optically Driven Terahertz Wave Modulator Using Ring-Shaped Microstripline With GaInAs Photoconductive Mesa Structure
To improve wireless communications systems, it is desirable to seamlessly combine fiber-based optical and terahertz wireless communications systems. In this paper, we demonstrate a waveguide optically driven terahertz wave modulator using a ring-shaped microstripline with a GaInAs photoconductive mesa structure. In this device, terahertz wave modulation is performed by controlling the photo-generated carriers in the GaInAs mesa. As a result, a maximum extinction ratio of 16.8 dB in the terahertz band was obtained with a light irradiation of 15 dBm (32 mW), and the 3 dB modulation bandwidth was approximately 170 MHz.
- 1 September 2016
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2016-02 (53) , 4005
High-Rate Homoepitaxial Growth of Heavily Boron-Doped Diamond (100) Films By Microwave Plasma-Enhanced Chemical Vapor Deposition Using High Microwave Power Density
Diamond is expected as a next-generation semiconductor material for high-power devices because of its high breakdown electric field, mobility, and thermal conductivity. For the power devices with high current operation, vertical structures are effective because the large contact area is easily obtained by trench structures in the same way as silicon and silicon carbide power devices. The low resistivity diamond single-crystal substrates are required to fabricate the diamond vertical power devices and are realized by heavy boron doping. The highest growth rate of heavily boron-doped ([B]film > 1020 atoms/cm3) diamond films obtained by microwave plasma-enhanced chemical vapor deposition (MPECVD) is 6 μm/h [1]. The higher growth rate is required for manufacturing cost reduction of the low resistivity diamond substrates. However, the higher the boron concentration is, the lower the growth rate of the diamond films becomes [1]. It is known that there are mainly two methods for increasing the growth rate of the diamond films. One is a nitrogen addition to the plasma. However, incorporated nitrogen into diamond acts as a donor, which is compensator for boron-doped diamond [2]. The other is high density of the microwave power input into the plasma. Therefore, we tried to change the shape of a diamond substrate holder for MPECVD to improve the growth rate by increasing the power density near the surface of substrate. Figure 1 shows the plasma states of (a) the conventional substrate holder and (b) the improved substrate holder. The improved substrate holder has a shallower bottom than the conventional one. In the case of the improved substrate holder, the top of the diamond substrate is higher than that of the holder, as shown in Fig.1(b). As a result, the diamond growth rate and incorporation of boron atoms into the diamond film are enhanced at the same time because the electric field is concentrated at the top surface of the diamond substrate and the radical density on the diamond surface increases. High-pressure, high-temperature (HPHT) synthetic Ib(100) single-crystal diamonds were used as substrates for the homoepitaxial diamond growth by MPECVD with a spherical resonator structure (Arios Inc. in Japan). Before the CVD growth, the diamond substrates were treated with HF diluted with H2O for 15 min. Next, the substrates were heated in 2:1 mixture of H2O2 and H2SO4 at 400°C for 15 min. The growth was carried out using CH4 and B(CH3)3 diluted with H2. The microwave power, the total pressure and the methane concentration were maintained at 900 W, 50 kPa and 2.4 %, respectively. The boron/carbon (B/C) ratios in the gas phase were fixed at 14,000 ppm for the conventional holder and 20,000 ppm for the improved substrate holder, respectively. The growth of the heavily boron-doped diamond films was conducted for two hours in the above conditions. After the growth, the surface morphologies of the heavily boron-doped diamond films were observed by optical microscopy (OM). The resistivities of the films were measured by a van der Pauw contact configuration and the growth rates were estimated by the micrometer. Figure 2 shows the OM images of typical surface morphologies of the heavily boron-doped diamond films grown on diamond (100) substrates by (a) the conventional substrate holder and (b) the improved substrate holder. Although the diamond film grown by the conventional substrate holder had some non-epitaxial crystallites with density of 1.6 × 104 cm-2, which degrade the diamond device performances, the diamond film grown by the improved substrate holder had no non-epitaxial crystallites. The resistivities of the films were 3.3 × 10-2 Ωcm for the improved substrate holder and 2.3 × 10-2 Ωcm for the conventional substrate holder, respectively. The boron concentrations in these films were 1~3 × 1020 cm-3, which is estimated from the growth condition. The growth rates were 29.5 μm/h for the improved substrate holder and 13.0 μm/h for the conventional substrate holder, respectively. The growth rate of 29.5 μm/h is the highest growth rate for heavily boron-doped ([B]film> 1020 cm-3) diamond films. Acknowledgements This work was partially supported by Adaptable and Seamless Technology Transfer Program through Target-driven R&D, JST, and Kanazawa University SAKIGAKE Project. References [1] J. Achard et al., physi. status solidi, 209 (2012) 1651-1658. [2] A. Chayahara et al., Diamond Relat. Mater., 13 (2004) 1954-1958. Figure 1
- 1 September 2016
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2016-02 (53) , 4005
High-Rate Homoepitaxial Growth of Heavily Boron-Doped Diamond (100) Films By Microwave Plasma-Enhanced Chemical Vapor Deposition Using High Microwave Power Density
Diamond is expected as a next-generation semiconductor material for high-power devices because of its high breakdown electric field, mobility, and thermal conductivity. For the power devices with high current operation, vertical structures are effective because the large contact area is easily obtained by trench structures in the same way as silicon and silicon carbide power devices. The low resistivity diamond single-crystal substrates are required to fabricate the diamond vertical power devices and are realized by heavy boron doping. The highest growth rate of heavily boron-doped ([B]film > 1020 atoms/cm3) diamond films obtained by microwave plasma-enhanced chemical vapor deposition (MPECVD) is 6 μm/h [1]. The higher growth rate is required for manufacturing cost reduction of the low resistivity diamond substrates. However, the higher the boron concentration is, the lower the growth rate of the diamond films becomes [1]. It is known that there are mainly two methods for increasing the growth rate of the diamond films. One is a nitrogen addition to the plasma. However, incorporated nitrogen into diamond acts as a donor, which is compensator for boron-doped diamond [2]. The other is high density of the microwave power input into the plasma. Therefore, we tried to change the shape of a diamond substrate holder for MPECVD to improve the growth rate by increasing the power density near the surface of substrate. Figure 1 shows the plasma states of (a) the conventional substrate holder and (b) the improved substrate holder. The improved substrate holder has a shallower bottom than the conventional one. In the case of the improved substrate holder, the top of the diamond substrate is higher than that of the holder, as shown in Fig.1(b). As a result, the diamond growth rate and incorporation of boron atoms into the diamond film are enhanced at the same time because the electric field is concentrated at the top surface of the diamond substrate and the radical density on the diamond surface increases. High-pressure, high-temperature (HPHT) synthetic Ib(100) single-crystal diamonds were used as substrates for the homoepitaxial diamond growth by MPECVD with a spherical resonator structure (Arios Inc. in Japan). Before the CVD growth, the diamond substrates were treated with HF diluted with H2O for 15 min. Next, the substrates were heated in 2:1 mixture of H2O2 and H2SO4 at 400°C for 15 min. The growth was carried out using CH4 and B(CH3)3 diluted with H2. The microwave power, the total pressure and the methane concentration were maintained at 900 W, 50 kPa and 2.4 %, respectively. The boron/carbon (B/C) ratios in the gas phase were fixed at 14,000 ppm for the conventional holder and 20,000 ppm for the improved substrate holder, respectively. The growth of the heavily boron-doped diamond films was conducted for two hours in the above conditions. After the growth, the surface morphologies of the heavily boron-doped diamond films were observed by optical microscopy (OM). The resistivities of the films were measured by a van der Pauw contact configuration and the growth rates were estimated by the micrometer. Figure 2 shows the OM images of typical surface morphologies of the heavily boron-doped diamond films grown on diamond (100) substrates by (a) the conventional substrate holder and (b) the improved substrate holder. Although the diamond film grown by the conventional substrate holder had some non-epitaxial crystallites with density of 1.6 × 104 cm-2, which degrade the diamond device performances, the diamond film grown by the improved substrate holder had no non-epitaxial crystallites. The resistivities of the films were 3.3 × 10-2 Ωcm for the improved substrate holder and 2.3 × 10-2 Ωcm for the conventional substrate holder, respectively. The boron concentrations in these films were 1~3 × 1020 cm-3, which is estimated from the growth condition. The growth rates were 29.5 μm/h for the improved substrate holder and 13.0 μm/h for the conventional substrate holder, respectively. The growth rate of 29.5 μm/h is the highest growth rate for heavily boron-doped ([B]film> 1020 cm-3) diamond films. Acknowledgements This work was partially supported by Adaptable and Seamless Technology Transfer Program through Target-driven R&D, JST, and Kanazawa University SAKIGAKE Project. References [1] J. Achard et al., physi. status solidi, 209 (2012) 1651-1658. [2] A. Chayahara et al., Diamond Relat. Mater., 13 (2004) 1954-1958. Figure 1
- 1 April 2010
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 49 (4S) , 04DC17
High-Performance Three-Terminal Fin Field-Effect Transistors Fabricated by a Combination of Damage-Free Neutral-Beam Etching and Neutral-Beam Oxidation
Three-terminal fin field-effect transistors (3T-FinFETs) were fabricated by neutral-beam oxidation (NBO) to form gate silicon dioxide (SiO2). The 3T-FinFET fabricated by NBO showed higher device performance – namely, a higher subthreshold slope and a higher effective mobility – than that fabricated by conventional thermal oxidation. It is considered that those improved subthreshold slope and mobility are due to the fact that the three-dimensional structure of a SiO2 film fabricated by NBO has a lower interfacial state density and a lower roughness than a similar structure fabricated by the conventional thermal oxidation of a SiO2 film. The reasons for the lower interfacial state density and lower roughness are the low temperature and lattice plane independence of NBO in comparison with conventional thermal oxidation processes.
- 1 April 2010
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 49 (4S) , 04DC17
High-Performance Three-Terminal Fin Field-Effect Transistors Fabricated by a Combination of Damage-Free Neutral-Beam Etching and Neutral-Beam Oxidation
Three-terminal fin field-effect transistors (3T-FinFETs) were fabricated by neutral-beam oxidation (NBO) to form gate silicon dioxide (SiO2). The 3T-FinFET fabricated by NBO showed higher device performance – namely, a higher subthreshold slope and a higher effective mobility – than that fabricated by conventional thermal oxidation. It is considered that those improved subthreshold slope and mobility are due to the fact that the three-dimensional structure of a SiO2 film fabricated by NBO has a lower interfacial state density and a lower roughness than a similar structure fabricated by the conventional thermal oxidation of a SiO2 film. The reasons for the lower interfacial state density and lower roughness are the low temperature and lattice plane independence of NBO in comparison with conventional thermal oxidation processes.
- 1 May 2009
- Published by Elsevier in Diamond and Related Materials
- Vol. 18 (5-8) , 764-767
Electrical and light-emitting properties from (111)-oriented homoepitaxial diamond p–i–n junctions
- 1 May 2009
- Published by Elsevier in Diamond and Related Materials
- Vol. 18 (5-8) , 764-767
Electrical and light-emitting properties from (111)-oriented homoepitaxial diamond p–i–n junctions
- 13 January 2006
- Published by Wiley
- p. 38-44
Direct Chlorination of Alcohols: Synthesis of Ethyl 3‐Chloro‐3‐Phenylpropanoate
- 13 January 2006
- Published by Wiley
- p. 38-44
Direct Chlorination of Alcohols: Synthesis of Ethyl 3‐Chloro‐3‐Phenylpropanoate
- 1 May 2004
- Published by Elsevier in Thin Solid Films
- Vol. 455-456, 759-763
Atomic-layer resolved monitoring of thermal oxidation of Si(001) by reflectance difference oscillation technique
- 1 May 2004
- Published by Elsevier in Thin Solid Films
- Vol. 455-456, 759-763
Atomic-layer resolved monitoring of thermal oxidation of Si(001) by reflectance difference oscillation technique
- 1 April 2002
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 299-302, 575-578
In situ ESR observation of interface dangling bond formation processes during amorphous SiO2 growth on Si
- 1 April 2002
- Published by Elsevier in Journal of Non-Crystalline Solids
- Vol. 299-302, 575-578
In situ ESR observation of interface dangling bond formation processes during amorphous SiO2 growth on Si