RKRaja Yasir Mehmood Khan

Raja Yasir Mehmood Khan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Raja Yasir Mehmood Khan has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Rahim Ullah

    National Institute of Lasers and Optronics College, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad 45650, Pakistan

    8 shared publications
  • Muhammad Faisal

    National Institute of Lasers and Optronics College, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad 45650, Pakistan

    7 shared publications
  • Hinna Tariq

    National Institute of Lasers and Optronics College, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad 45650, Pakistan

    1 shared publication
  • Kamran Ahmad

    Pakistan Tokamak Plasma Research Institute, P.O. Box 3329, Islamabad, Pakistan

    1 shared publication
  • Muhammad Faisal

    National Institute of Lasers and Optronics College, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad 45650, Pakistan

    1 shared publication

Latest Publications

  • High sensitive and thermally stable fiber Bragg grating magnetic field sensor

    by Raja Yasir Mehmood Khan, Hinna Tariq, Rahim Ullah, Muhammad Faisal

    Precision magnetic field sensing plays an important role in various fields, including navigation, geological exploration, industrial system monitoring, and medical diagnostics. In this study, we developed a temperature-independent, high-precision magnetic field sensor based on fiber Bragg grating (FBG) technology. The sensor operates on the principle of strain induced in the FBG through the interaction between a permanent magnet mounted at the tip of a stainless-steel cantilever and an external magnetic field. Under tensile strain, the sensor’s magnetic field sensitivity ranging from 0.35 pm G −1 to 1.41 pm G −1 , corresponding to an increase in magnet strength from 550 G to 2380 G. The highest magnetic field resolution achieved was 7.092 G. Due to the sensor’s nonlinear response at higher field strengths, the sensor was optimized using a 2100 G permanent magnet for further characterization. The optimized sensor demonstrated a consistent and reliable response to varying external magnetic fields, with less than 1% hysteresis during cyclic measurements.


  • Open Access

    High-Temperature Sensing with Iron-Ceramic Enhanced Fiber Bragg Grating Sensors: Encapsulation Strategies and Concentration Dependencies

    by Raja Yasir Mehmood Khan, Rahim Ullah, Muhammad Faisal

    This research article primarily aims to enable type-I fiber Bragg grating (FBG) for high-temperature sensing and to explore the influence of varying concentrations of iron fillings in the ceramic on the sensor's sensitivity and response time. A set of six identical probes were fabricated, each with a different iron filling concentration ranging from 0% to 50%. Increasing the iron filling concentration from 0% to 50% enhanced the temperature sensitivity of the probe from 14.08 ± 0.24 pm/°C to 14.67 ± 0.17 pm/°C. To evaluate the response time, the probes were subjected to an abrupt heating process from 27 °C to 700 °C, and the duration was measured. The response time improved from 270 s to 180 s, representing a 33.33% improvement, as the iron filling concentration increased from 0% to 50%. Beyond a 40% concentration, both the temperature sensitivity and response time reached saturation. The lifetime of the optimized probe with a 40% iron filling concentration is estimated to be 4.46 years. During repeated exposures to high temperatures, no permanent drift in its Bragg wavelength was observed, and its repeatability during a heating-cooling cycle exhibited hysteresis of less than 1%. Received: 23 April 2024 | Revised: 30 June 2024 | Accepted: 18 October 2024 Conflicts of Interest The authors declare that they have no conflicts of interest to this work. Data Availability Statement The data that support the findings of this study are available within the manuscript. Author Contribution Statement Raja Yasir Mehmood Khan: Conceptualization, Methodology, Software, Validation, Formal analysis, Investigation, Resources, Writing – original draft, Visualization. Rahim Ullah: Conceptualization, Validation, Resources, Data curation, Writing – original draft. Muhammad Faisal: Conceptualization, Validation, Resources, Data curation, Writing – review & editing, Visualization, Supervision, Project administration.


  • Open Access

    The development of multiplexing capability for reflective matched fiber bragg gratings interrogation technique and its application in real-time micro cracks detection

    by Raja Yasir Mehmood Khan, Rahim Ullah, Muhammad Faisal

    Cracks detection in engineering structures is pivotal for ensuring structural reliability and preventing catastrophic failures. In this article we developed multiplexing capability of reflective matched fiber Bragg Gratings (RM-FBGs) interrogation technique and utilized it for crack detection in an assembly aluminum plates. Firstly, the proposed multiplexing capability is analyzed by applying axial strain on an array of five FBGs pasted on five separate aluminum assemblies. The strain in any FBG due to localized micro-crack resulted in variation its output itself by ascertaining no effect in the outputs of other FBGs, certifying the multiplexing capability of RM-FBGs scheme. The developed RM-FBGs scheme is practically applied micro-cracks detection in a V-shape crack produced in assembly of aluminum plates. The crack is monitored by an array of three multiplexed FBGs epoxied to the plate’s junction at three different positions P1, P2 and P3. Where P1 is at beginning, P2 is at middle and P3 is at end of the crack. Sensitivities of the FBGs at points P1, P2 and P3 were found to be 0.09 ± 0.0001 V μm−1, 0.10 ± 0.007 V μm−1 and 1.08 ± 0.09 V μm−1, respectively and resolutions were found to be 0.22 μm, 0.20 μm and 0.02 μm, respectively. Variation in gauge length of the optical fiber from 100 mm to 200 mm resulted in 76.36% increase in crack width sensing range but at the cost of compromise in sensitivity and resolution. The proposed multiplexed RM-FBG can be deployed for early micro-cracks detection in metallic and non-metallic structures with sub-micrometers resolution.


  • Fiber Bragg grating guided laser interferometer-based highly sensitive vacuum pressure sensor

    by Rahim Ullah, Raja Yasir Mehmood Khan, Kamran Ahmad, Muhammad Faisal

    Vacuum sensing and metrology pave the way for promising solutions to fulfill the scientific and technological demands of various contemporary industries and research fields. This study introduces an innovative vacuum pressure sensor, employing a fiber Bragg grating (FBG) guided Michelson interferometer. The sensor works on the principle of interferometric measurement of precisely gauging the displacement of an elastic diaphragm with pressure variation connected to a vacuum chamber in terms of interference fringe counts due to arm-length variation of the interferometer. The elastic silicone diaphragm and stainless steel cantilever, being critical components of the sensor, were examined using finite element analysis and subsequently demonstrated experimentally. The diaphragm’s position is continuously monitored in real time through the Bragg’s wavelength of the FBG, continuously updating the interferometer after each 15 ms for the accurate measurement of fluctuating vacuum pressures. The strain-induced shift in the FBG’s Bragg wavelength follows a linear trend with pressure variation, exhibiting a sensitivity of 12.7 pm/mbar. With a dynamic range spanning 0.05–100 mbar, the sensor demonstrates a sensitivity of 16.073 fringe counts/mbar and a notable resolution of 0.3364 mbar. Moreover, the sensor exhibits good repeatability, with a hysteresis of up to 2.59% during full span cyclic operation. The coupling of the interferometer with FBG makes it a unique secondary standard solution for precision vacuum measurement.


  • Fabrication and characterization of a rapid-response, ultrasensitive dual-head interferometric pressure sensor

    by Rahim Ullah, Raja Yasir Mehmood Khan, Muhammad Faisal

    A novel, to the best of our knowledge, dual-head Michelson interferometer-based pressure sensor with ultrahigh sensitivity and rapid response has been fabricated and optimized. The sensor consists of two diaphragm-based sensing heads, which operate on the principle of path-length variations of the interferometers due to the effect of pressure variation within the pressure channel. Pressure has been measured independently by the heads in terms of the fringe counts across two photodetectors with different sensitivities and working ranges. Head 1 had a linear working range of 0-6 psi and a sensitivity, resolution, and response time of 1295.04 fringe counts/psi, 25.74 mu psi, and 0.86 ms, respectively, which were 2.46, 2.46, and 0.86 times better than those of head 2. However, head 2 had a larger working range of 0-15 psi. Heads 1 and 2 yielded repeatable responses with negligible hysteresis and an average absolute error of 0.55% and 0.58%, respectively, compared to the predicted results. The proposed sensor has great potential for use in laboratory and industrial nonintrusive precise and fast-response pressure sensing applications. (c) 2023 Optica Publishing Group


  • Design and development of cost-effective fiber Bragg grating temperature sensor package

    by Raja Yasir Mehmood Khan, Rahim Ullah, Muhammad Faisal

    A cost-effective fiber Bragg grating (FBG) temperature sensor package was designed and developed with two distinct sensing probes and demodulation schemes. U-shaped and capillary shape probes were designed and tested using an optical spectrum analyzer and two different indiginously developed intensity demodulation schemes. The temperature sensitivities were measured as 12.94 ± 0.15 pm °C−1, 11.57 ± 0.12 pm °C−1, and 12.03 ± 0.14 pm °C−1 for a bare FBG and for FBGs encapsulated in the U-shaped and capillary probes, respectively, with negligible hysteresis and a repeatability of 1 °C–3 °C. The performance of the probes was demonstrated by twin-FBG intensity demodulation schemes, the range of which was increased up to 181.50 °C with a resolution of 0.120 °C by the development of a CFBG-FBG intensity demodulation scheme.


  • Design and development of type-1 FBG based high temperature sensor

    by R Y M Khan, R Ullah, M Faisal

    Thermal metrology is critical in many high-energy industrial processes to optimize the process efficiency, energy consumption and quality of end product. Here, we present the design and development of a double thimble type standard type-1 fiber Bragg grating (FBG) high temperature sensing probes. Two different probes named probe-1 and probe-2 are developed by encapsulating type-1 FBGs in two stainless steel thimbles with ceramic filling. The probes are experimentally tested in a high temperature box furnace and their responses are interrogated by an optical spectrum analyzer. FBGs encapsulated in both probe-1 and probe-2 exhibited a linear red-shift in their Bragg wavelength with increase in temperature from 30 °C to 700 °C with sensitivities of 13.86 ± 0.1 pm/°C and 14.10 ± 0.2 pm/°C which are 4.8% and 3.16% lower than temperature sensitivity of bare FBG, respectively. A deformation in the Bragg spectrum of probe-1 is observed at temperatures above 500 °C however, probe-2 is found to be thermally stable up to 700 °C. An estimated life-time of about 6 years is offered by the optimized probe-2 with a negligible hysteresis and repeatability of 1°C–5°C.


  • Design and development of an economical temperature compensated bidirectional fiber Bragg grating flow sensor

    by Rahim Ullah, Raja Yasir Mehmood Khan, Muhammad Faisal

    A target-type cantilever based temperature compensated fiber Bragg grating (FBG) flow sensor is designed and developed with economical demodulation and data acquisition schemes. FBG is glued on the surface of a thin elastic stainless steel cantilever in pre-strained condition. The cantilever is mounted inside a flow channel by a special purpose brass holder with a height and direction adjustable threaded stem. The sensor is interrogated by an optical spectrum analyzer (OSA) and indigenously developed twin FBGs and chirped FBG—FBG intensity demodulation schemes. Response of the sensor is investigated in the flow rate range of 0–10 l min−1 in both forward and reverse flow directions. In spectral demodulation, the flow sensor offered a linear response in the full investigated range with a sensitivity of 19.2 pm/(L/min). However, the twin FBGs demodulation scheme presented a linear behaviour in the range of 4–10 l min−1 with sensitivities of 1.22 ± 0.03 μW/(L/min) and 29.89 ± 0.55 mV/(L/min) detected by the high speed power meter and photodetector, respectively. The novel CFBG-FBG intensity demodulator offered a linear response throughout its tested range and can offer a flow rate detection up to 265 l min−1 at the present sensitivity of the sensor with the condition that the cantilever-FBG system must be strong enough to withstand the higher flow rates. The temperature of the fluid is monitored by an FBG temperature sensing probe connected to the flow channel using intensity demodulation scheme by another pair of twin FBGs. Temperature compensation of the flow sensor is performed by arithmetic operations over the reflection intensities due to temperature probe to the results of the flow rates using a cost-effective data acquisition scheme.