Dmitriy Nikolaevich Bozhko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Dmitriy Nikolaevich Bozhko has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Evgeniy Gennadyevich Partyko
School of Non-Ferrous Metals, Siberian Federal University, 660041 Krasnoyarsk, Russia
4 shared publications - Yulbarskhon Nabievich Mansurov
Department of Wagons and Wagon Economy, Tashkent State Transport University, Tashkent 100067, Uzbekistan
4 shared publications - Aleksandr Aleksandrovich Kosovich
School of Non-Ferrous Metals, Siberian Federal University, 660041 Krasnoyarsk, Russia
3 shared publications - Yuriy Viktorovich Baykovskiy
Siberian Federal University, Krasnoyarsk, Russian Federation
3 shared publications - Igor Lazarevich Konstantinov
Siberian Federal University, Krasnoyarsk, Russian Federation
2 shared publications - Pavel O. Yuryev
Siberian Federal University, Krasnoyarsk, Russian Federation
2 shared publications
Latest Publications
- Open Access
Analysis of Composition, Properties, and Usage Efficiency of Different Commercial Salt Fluxes for Aluminum Alloy Refining
One of the key problems in the billet and shaped casting of aluminum alloys is the presence of various undesirable inclusions and impurities in the melt, which can serve as stress concentrators in the finished product, as well as dissolved hydrogen, which contributes to the formation of porosity. The interaction of aluminum with other gases produced by the combustion of fuel particles, oil, and paint materials brought into the furnace together with charge and scrap increases the amount of nitrides, oxides, carbides, and sulfides in the melt. Flux treatment is widely used as protection of aluminum alloys from oxidation and removal of impurities. The present paper reports the data of a comparative analysis of five widely used flux compositions based on sodium, potassium, and magnesium chlorides. The study covers the following aspects: chemical composition, moisture content, melting temperature and melting range, particle size distribution, and refining ability as measured by the change in Na, Ca, and H2 content after melt treatment.
Open AccessAnalysis of Composition, Properties, and Usage Efficiency of Different Commercial Salt Fluxes for Aluminum Alloy Refining
One of the key problems in the billet and shaped casting of aluminum alloys is the presence of various undesirable inclusions and impurities in the melt, which can serve as stress concentrators in the finished product, as well as dissolved hydrogen, which contributes to the formation of porosity. The interaction of aluminum with other gases produced by the combustion of fuel particles, oil, and paint materials brought into the furnace together with charge and scrap increases the amount of nitrides, oxides, carbides, and sulfides in the melt. Flux treatment is widely used as protection of aluminum alloys from oxidation and removal of impurities. The present paper reports the data of a comparative analysis of five widely used flux compositions based on sodium, potassium, and magnesium chlorides. The study covers the following aspects: chemical composition, moisture content, melting temperature and melting range, particle size distribution, and refining ability as measured by the change in Na, Ca, and H2 content after melt treatment.
- 11 December 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (8) , 1231-1239
Study of deformability during the rolling of aluminum alloy 1580 doped with small additions of erbium and ytterbium
- 11 December 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (8) , 1231-1239
Study of deformability during the rolling of aluminum alloy 1580 doped with small additions of erbium and ytterbium
- 1 May 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (1) , 91-99
Determination of the coefficients of rheological equation of Al–Zr alloy under hot plastic deformation conditions
- 1 May 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (1) , 91-99
Determination of the coefficients of rheological equation of Al–Zr alloy under hot plastic deformation conditions
- 18 February 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 125 (11-12) , 5799-5806
An approach to calculating the energy-power parameters of metal pressing process by the conform method
- 18 February 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 125 (11-12) , 5799-5806
An approach to calculating the energy-power parameters of metal pressing process by the conform method