Tim Simon Krüger
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tim Simon Krüger has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jürgen Maas
Mechatronic Systems Lab Technische Universität Berlin Hardenbergstraße 36 10623 Berlin Germany
2 shared publications - Abd Elkarim Masoud
Mechatronic Systems Lab, technical university of berlin, Berlin, Germany
1 shared publication - Andreas Hubracht
Technische Universität Berlin, Mechatronic Systems Lab, Hardenbergstraße 36, 10623 Berlin, Germany
1 shared publication - Jana Mertens
Technische Universität Berlin, Mechatronic Systems Lab, Hardenbergstraße 36, 10623 Berlin, Germany
1 shared publication Ozan Çabuk
Technische Universität Berlin, Mechatronic Systems Lab, Hardenbergstraße 36, 10623 Berlin, Germany
1 shared publication- Ozan Çabuk
Mechatronic Systems Laboratory, Technische Universität Berlin, Hardenbergstraße 36, 10623 Berlin, Germany
1 shared publication
Latest Publications
- Open Access
- 29 August 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (9) , 095041
Modeling and experimental investigation of multilayer DE transducers considering the influence of the electrode layers
A current research topic for dielectric elastomer (DE) materials is the reduction of the thickness of the DE layer in order to achieve a lower operating voltage with the same electric field strength. As the ratio of the layer thicknesses of the electrode to the elastomer is therefore more important, the mechanical properties of the electrode layers are of greater significance. Several research articles deal with investigations, exploring the influence of electrode materials on the behavior of the DE transducer and emphasizing its importance. In analytical models, however, the electrodes are not usually considered separately, but the parameters are identified for the entire DE composite, consisting of elastomer and electrode layers. In contrast, in this article the material characterization is carried out separately for the two materials in a first step. In a further step, a holistic model for multilayer DE transducers is derived on the basis of this material-specific characterization and subsequently validated with measurements. For the DE layers, ELASTOSIL ® 2030 (EL 2030), and for the electrode layers, ELASTOSIL ® LR 3162 (EL 3162) are investigated, frequently used materials for DE transducers that offer reproducible properties for the investigation. EL 3162 is a carbon black filled elastomer material that exhibits higher elastic and viscose stresses as well as a significant rate-independent hysteresis compared to EL 2030. Experimental investigations of DE transducers with different electrode thicknesses are examined to validate the model and to demonstrate the significance and influence of the electrode layers on the transducer’s performance. Furthermore, the influence of the electrode properties on the actuator, generator and sensor behavior of the DE transducer is analyzed based on the developed model. Depending on the thickness and number of layers, this underlines the relevance of the electrode properties and provides information on the optimized design of the DE transducer.
- 29 August 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (9) , 095041
Open AccessModeling and experimental investigation of multilayer DE transducers considering the influence of the electrode layers
A current research topic for dielectric elastomer (DE) materials is the reduction of the thickness of the DE layer in order to achieve a lower operating voltage with the same electric field strength. As the ratio of the layer thicknesses of the electrode to the elastomer is therefore more important, the mechanical properties of the electrode layers are of greater significance. Several research articles deal with investigations, exploring the influence of electrode materials on the behavior of the DE transducer and emphasizing its importance. In analytical models, however, the electrodes are not usually considered separately, but the parameters are identified for the entire DE composite, consisting of elastomer and electrode layers. In contrast, in this article the material characterization is carried out separately for the two materials in a first step. In a further step, a holistic model for multilayer DE transducers is derived on the basis of this material-specific characterization and subsequently validated with measurements. For the DE layers, ELASTOSIL ® 2030 (EL 2030), and for the electrode layers, ELASTOSIL ® LR 3162 (EL 3162) are investigated, frequently used materials for DE transducers that offer reproducible properties for the investigation. EL 3162 is a carbon black filled elastomer material that exhibits higher elastic and viscose stresses as well as a significant rate-independent hysteresis compared to EL 2030. Experimental investigations of DE transducers with different electrode thicknesses are examined to validate the model and to demonstrate the significance and influence of the electrode layers on the transducer’s performance. Furthermore, the influence of the electrode properties on the actuator, generator and sensor behavior of the DE transducer is analyzed based on the developed model. Depending on the thickness and number of layers, this underlines the relevance of the electrode properties and provides information on the optimized design of the DE transducer.
- Open Access
Manufacturing Process for Multilayer Dielectric Elastomer Transducers Based on Sheet-to-Sheet Lamination and Contactless Electrode Application
Dielectric elastomer transducers (DETs) consist of thin elastomer films and compliant conductive electrodes on each side. Several DE-based systems, e.g., DE actuators, loudspeakers or sensors, have great potential in industrial applications. Different manufacturing processes for DE-based transducers have been realized so far. An alternative manufacturing process, based on sheet-to-sheet lamination of pre-fabricated elastomer films, appears promising for the manufacturing of large numbers of DETs, as, on the one hand, the commercially available elastomer films produced are characterized by homogeneous and reproducible properties and, on the other hand, the curing time during processing can be avoided. However, the handling of thin elastomer films and a controlled film transfer onto a surface is a challenge, as pre-stretch and wrinkles can easily occur. The presented sheet-to-sheet lamination mechanism facilitates controllable film handling well, whereby a high number of DE layers can be achieved. This paper focuses on the developed, automated film lamination of pre-cut film sheets and the electrode application via a jetting system, representing core components of the corresponding overall manufacturing process of DE laminates. The process realization on a laboratory scale is presented and manufactured DET specimens investigated for validation purposes.
Open AccessManufacturing Process for Multilayer Dielectric Elastomer Transducers Based on Sheet-to-Sheet Lamination and Contactless Electrode Application
Dielectric elastomer transducers (DETs) consist of thin elastomer films and compliant conductive electrodes on each side. Several DE-based systems, e.g., DE actuators, loudspeakers or sensors, have great potential in industrial applications. Different manufacturing processes for DE-based transducers have been realized so far. An alternative manufacturing process, based on sheet-to-sheet lamination of pre-fabricated elastomer films, appears promising for the manufacturing of large numbers of DETs, as, on the one hand, the commercially available elastomer films produced are characterized by homogeneous and reproducible properties and, on the other hand, the curing time during processing can be avoided. However, the handling of thin elastomer films and a controlled film transfer onto a surface is a challenge, as pre-stretch and wrinkles can easily occur. The presented sheet-to-sheet lamination mechanism facilitates controllable film handling well, whereby a high number of DE layers can be achieved. This paper focuses on the developed, automated film lamination of pre-cut film sheets and the electrode application via a jetting system, representing core components of the corresponding overall manufacturing process of DE laminates. The process realization on a laboratory scale is presented and manufactured DET specimens investigated for validation purposes.