MTMark Talesnick

Mark Talesnick

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mark Talesnick has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Laterally confined consolidation of slurried fine-grained soils, and critical state parameters

    by S. Nachum, M. Talesnick

    A series of one-dimensional, laterally confined consolidation tests was carried out on reconstituted and slurried clays. Reconstituted clay, prepared as a slurry, underwent loading and unloading in a rectangular cell in which null pressure gauges were installed in the walls, allowing reliable measurement of lateral stress. The results of the virgin loading stages showed equivalency between the compression index, $$C_{c}$$ C c , which relates the void ratio to the vertical effective stress, and the critical state compression parameter, $$\lambda$$ λ , which relates void ratio to the isotropic or mean effective stress, as long $$\lambda$$ λ is obtained from one-dimensional compression. This equivalency is shown to be consistent with constant $$K_{0}$$ K 0 during virgin loading. On the other hand, during unloading, the expansion indices differed significantly, and non-equivalency was demonstrated between the parameters $$C_{e}$$ C e , the expansion index, and the critical state parameter, $$\kappa$$ κ , consistent with a non-constant unloading earth pressure coefficient, $$K_{0} ^{\prime}$$ K 0 ′ . Isotropic consolidation tests performed on the same soils yielded compression indices, $$\lambda$$ λ , consistently slightly lower—80–86% of the laterally confined values, suggesting that compressibility may depend on the imposed stress path, while expansion indices, $$\kappa$$ κ , were equal to the one-dimensional values. A rational expression for the relationship between $$K_{0} ^{\prime}$$ K 0 ′ and $$K_{0}$$ K 0 , in terms of the expansion indices relative to vertical and lateral stress, respectively, $$C_{e}$$ C e , $$C_{e,h}$$ C e , h , is presented.

  • Open Access

    Particulate-Sensor Interaction and Its Influence on Stress Measurements in Granular Media

    by Mark Talesnick, Noa Dolev, Shay Nachum

    Accurate pressure measurements in soils and other particulate media are essential for the development and validation of engineering models. Pressure transducers based on deflecting membranes remain widely used despite longstanding recognition that sensor deformation may influence the measured response. This study investigates the extent to which hysteresis observed during load–unload cycles originates from sensor–material interaction rather than intrinsic material behavior. Controlled experiments were conducted on dune sand and uniform glass beads using sensors operating in membrane-deflection mode and Null mode, together with direct measurements of local material deformation. The results show that even small membrane deflections generate pronounced apparent hysteresis and that conventional calibration procedures cannot reliably eliminate this effect, even when performed under matching test conditions. The resulting measurement errors become particularly significant during unloading. Direct observations reveal that during loading, the surrounding soil accommodates the elastic deflection of the membrane. During unloading, however, the surrounding soil does not accommodate membrane recovery, preventing the membrane from rebounding along its elastic path. In contrast, Null-mode measurements exhibit a nearly unique response with substantially reduced hysteresis and little dependence on sensor stiffness. The findings indicate that a significant portion of hysteresis commonly reported in pressure measurements may reflect measurement-induced effects rather than intrinsic material behavior, highlighting the importance of accounting for sensor–material interaction when interpreting experimental data and validating engineering models.

  • The Effects of Boundary Conditions in the Testing of Geotechnical Models

    by Shay Nachum, Peter Adesina, Shahpar Shoghi, Sam Frydman, Mark Talesnick

    The effects of boundary conditions, most importantly sidewall friction, on the outcome and subsequent interpretation and analysis of physical models in geotechnics are seldom given the attention required. Sidewall friction has significant influence on stress conditions within a specimen or model, and as such will affect the distribution of strain within the soil mass. A set of tests with fine grained uniform sand was performed in which sidewall friction and sidewall fixities were controlled and measured as loads were applied to the soil mass. As the specimen was loaded, shear stresses at the boundary of the test box, over the height of the specimen, were measured. Analysis of the test data reveals that during the loading stage of the experiment the development of shear stress is uniform and well understood. During unloading, the situation was shown to be more complex; sidewall shear is nonuniform over the sidewall height and changes sign as unloading progresses. The experimental data and analysis illustrate that by applying friction reduction measures, the effects of sidewall friction are significantly reduced. It is suggested that friction reduction measures are almost mandatory in two-dimensional physical model and element testing where the model thickness is typically very small. This could also be true in axisymmetric conditions, as illustrated by results from model cone penetration testing.

  • Open Access

    Boundary and internal sensing of granular instability in dry sand tilt-table tests

    by E. Treflik-Body, I. Omer, M. Talesnick, E. Steel, R. Mulligan, W.A. Take

    This work explores the phenomena of instability in low stress tilt-testing of dry sands using novel imbedded shear stress and strain sensors to capture quantitative data of constitutive behaviour leading up to and during instability. A unique strategy of testing dry soil enabled the investigation of instability in isolation from pore pressure consequences. Six shear stress and shear distortion sensors were distributed along the transparent sidewall and centre of the tilt-table, which was then rotated until instability and failure. Shear strain measured next to the transparent sidewall were 50% of those measured along the table centerline. Friction reduction strategies were successful in significantly reducing, but not eliminating, this discrepancy. Soil layers tilted until reaching instability, unloaded, and subjected to a second tilt cycle only exhibit instability at angles in excess of the first instability event. This phenomenon, analogous to the Kaiser effect, reveals the importance of void ratio with respect to instability. Tilt-table testing, when equipped with internal shear distortion sensors, was shown to be able to capture the modulus degradation curve over the strain range of 10 −5 to 10 −1 providing a promising new experimental technique to explore the stiffness degradation curve at very low confining pressures.


  • The full state of stress in monotonic simple shear tests on sand

    by Mason Ghafghazi, Mark Talesnick, Farid Ahmadi Givi

    The simple shear test has been an important tool in practical geotechnical engineering and the study of soil behaviour. The attractiveness of the simple shear test is founded in its relative ease of specimen preparation, similarity to at-rest conditions during consolidation and rotation of principal stresses during shear. Despite this test's attractive qualities, there are significant deficiencies in the interpretation of standard test results: horizontal normal stresses are not known and excess pore pressures are often interpreted from assumptions about constant-volume tests without saturation. To address this problem, a set of monotonic tests were performed on a sand, during which horizontal normal stresses were measured in the central portion of specimens. Based on the measurements, the full state of stress was defined, stress paths were drawn and directions of the principal stresses were determined. Outcomes showed that the conventional approach of estimating excess pore pressures as the change in vertical pressure to maintain constant volume in response to shear is problematic, and friction angles interpreted from conventionally measured shear and vertical stresses may be grossly underestimated in some cases.


  • Development of Tools for the Direct Measurement of Shear Stress and Shear Strain within a Soil Mass

    by M. Talesnick, I. Omer, M. Ringel, M. Ghafghazi

    This article describes the development of sensing tools designed and applied to the direct measurement of shear stresses and shear strain within a soil mass. The importance in the development of these tools is in their ability to measure shear stresses and shear distortions within soil without any a priori information of the stress and strains applied at the boundaries of the system. These tools may be applied to element testing, testing of physical models, and field applications. The sensors were used in the testing of a sand in a large simple shear apparatus, under both constant height and constant vertical pressure conditions. Testing demonstrated that shear stresses smaller than 0.1 kPa are easily resolved. Shear strains smaller than 10−5 (abs) were reliably measured. Measurement of shear stress and shear distortion within the soil mass allows for direct determination of the shear stiffness of the soil. Shear stiffness measured in this fashion is significantly greater than that determined from the globally measured shear stress and shear strain. The stiffness degradation curve illustrates a constant shear stiffness over the range of 10−5 through 5·10−4.


  • Application of TDR in compacted clay soils: Issues of dry density, water content range, and calibration

    by Shay Nachum, Mark Talesnick, Alex Furman

    The paper deals with three issues relevant to the application of TDR methods for monitoring water content in compacted clay soils: ( i) the dependence on dry density, ( ii) the ability to monitor changes in water content in clay soil approaching saturation, and ( iii) difficulties in performing efficient and reliable calibrations. A calibration scheme which inherently controls dry density of the specimen has been developed and applied. The methodology creates continuous calibration curves over a range of volumetric water content from a single test specimen. The new approach has been applied in monitoring the advance of a wetting front through a compacted swelling clay in a laboratory environment.


  • A New Apparatus for Studying Laterally Restrained Swell of Compacted Clay with Lateral Pressure Measurement

    by Shay Nachum, Mark Talesnick, Sam Frydman

    Wetting of compacted clays, and their subsequent swelling, often results in damage to structures and infrastructures. In some cases, for example, if the clay is adjacent to a structure such as a retaining wall, pile, or pipeline, lateral swell is restrained, resulting in heave in the vertical direction and development of swelling pressure laterally. Standard procedures for testing the swell of clays on wetting are limited to the definition of a vertical pressure-swell relationship. This paper presents an investigation of the laterally restrained swell of a highly plastic compacted clay in a new rectangular test cell designed to provide additional and more reliable test information. Lateral soil pressure is measured using null pressure gauges flush with the cell walls. Cell sidewall friction is evaluated by measuring the load applied to the specimen top and the load reaching its base, and it is minimized by incorporating friction reduction measures. It was found that pressure-swell curves, based on vertical pressure, horizontal pressure, and mean pressure, all plot as straight lines on a semi-log basis. Although inundation of the test specimen is standard practice for swelling tests, this procedure represents an extreme wetting condition in the field. The study demonstrates that swell is affected by the characteristics of the hydraulic head responsible for wetting the soil; wetting by suction alone, or by combination of suction and gravity head, result in different degrees of swell.