JuKyung Cha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
JuKyung Cha has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Seungyong Hahn
Seoul National University
18 shared publications - Jonghoon Yoon
Department of Electrical and Computer Engineering, Seoul National University, Seoul, Republic of Korea
14 shared publications - Jaheum Koo
Department of Electrical and Computer Engineering, Seoul National University, Seoul, South Korea
13 shared publications - Geonyoung Kim
Department of Electrical and Computer Engineering, Seoul National University, Seoul, Republic of Korea
6 shared publications - Chaemin Im
Department of Electrical and Computer Engineering, Seoul National University, Seoul, Republic of Korea
5 shared publications - Hyunsoo Park
Department of Electrical and Computer Engineering, Seoul National University, Seoul, Republic of Korea
5 shared publications
Latest Publications
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Performance and Characteristic Evaluation of a No-Insulation Superconducting Field Coil for High-Speed Homopolar Motors: Electromagnetic, Structural, Thermal, and NI Behavior Analysis
Efforts have been made to enhance motor power output by employing superconducting technology. However, when the field coil is placed on the rotor, high-speed operation becomes impractical due to the limitations imposed by slip rings, brushes, and mechanical stability issues. As an alternative, homopolar motors have been explored for high-speed applications such as turbo generators and flywheel energy storage systems. In addition, no-insulation (NI) coils offer enhanced thermal and electrical stability, enabling higher current densities. This paper presents the electromagnetic, structural, and thermal design of a superconducting NI field coil for application in a high-speed homopolar motor. It is further observed that NI coils exhibit geometry-dependent flux linkage variations, resulting in leakage current. This study investigates how NI behavior changes with the homopolar motor's design parameters. The designed NI coil features an operating current of 301 A, an inductance of 7.6 mH, a maximum hoop strain of 4.75 $\times \, 10^{-2}$%, and thermal loss of 398 mW during a 0.25 A/s ramping rate current charging. The analysis of NI behavior shows that the leakage loss varies from 3.72 $\mu$W to 27.8 $\mu$W depending on the design parameters, but its impact on overall motor performance is negligible. Therefore, the proposed NI field coil demonstrates stable operation, confirming its applicability in high-speed homopolar motor systems.
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Performance and Characteristic Evaluation of a No-Insulation Superconducting Field Coil for High-Speed Homopolar Motors: Electromagnetic, Structural, Thermal, and NI Behavior Analysis
Efforts have been made to enhance motor power output by employing superconducting technology. However, when the field coil is placed on the rotor, high-speed operation becomes impractical due to the limitations imposed by slip rings, brushes, and mechanical stability issues. As an alternative, homopolar motors have been explored for high-speed applications such as turbo generators and flywheel energy storage systems. In addition, no-insulation (NI) coils offer enhanced thermal and electrical stability, enabling higher current densities. This paper presents the electromagnetic, structural, and thermal design of a superconducting NI field coil for application in a high-speed homopolar motor. It is further observed that NI coils exhibit geometry-dependent flux linkage variations, resulting in leakage current. This study investigates how NI behavior changes with the homopolar motor's design parameters. The designed NI coil features an operating current of 301 A, an inductance of 7.6 mH, a maximum hoop strain of 4.75 $\times \, 10^{-2}$%, and thermal loss of 398 mW during a 0.25 A/s ramping rate current charging. The analysis of NI behavior shows that the leakage loss varies from 3.72 $\mu$W to 27.8 $\mu$W depending on the design parameters, but its impact on overall motor performance is negligible. Therefore, the proposed NI field coil demonstrates stable operation, confirming its applicability in high-speed homopolar motor systems.
- 13 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Design, Fabrication, and Experiment of Proto-Type Miniature Cylindrical Bulk YBCO Induction Motor for Cryogen Pump
The conceptual design, prototype fabrication, and experimental evaluation of a pipe-integrated cryogenic pump motor using a bulk YBCO superconductor in the rotor were conducted. An induction-type topology was adopted, utilizing a commercial copper-wound stator. The cylindrical bulk YBCO, mounted as the rotor, was designed under the assumption of liquid nitrogen flowing through a pipeline, allowing for direct cooling of the rotor. A locked-rotor experiment was performed on the fabricated prototype in a liquid nitrogen bath, and the equivalent critical current density was calculated through the finite element method (FEM) analysis based on the measured voltage and current data. Using the fitted parameters, the torque and output power characteristics of the motor were calculated, and the motor had approximately 50 W of output power under the given operating conditions.
- 13 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Design, Fabrication, and Experiment of Proto-Type Miniature Cylindrical Bulk YBCO Induction Motor for Cryogen Pump
The conceptual design, prototype fabrication, and experimental evaluation of a pipe-integrated cryogenic pump motor using a bulk YBCO superconductor in the rotor were conducted. An induction-type topology was adopted, utilizing a commercial copper-wound stator. The cylindrical bulk YBCO, mounted as the rotor, was designed under the assumption of liquid nitrogen flowing through a pipeline, allowing for direct cooling of the rotor. A locked-rotor experiment was performed on the fabricated prototype in a liquid nitrogen bath, and the equivalent critical current density was calculated through the finite element method (FEM) analysis based on the measured voltage and current data. Using the fitted parameters, the torque and output power characteristics of the motor were calculated, and the motor had approximately 50 W of output power under the given operating conditions.
- 23 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Electromagnetic-Thermal Design and Analysis of Liquid Nitrogen Immersed Aluminum Armature With NI HTS Field Windings
This paper presents an electromagnetic and thermal design methodology for a liquid-nitrogen (LN $_{2}$)-immersed aluminum armature with noinsulation hightemperature superconducting (NIHTS) field windings. A three-dimensional finite-element model is developed to optimize both the armature geometry and the NI-HTS coil configuration. The analysis evaluates key electromagnetic performance metrics, including torque density and electromagnetic coupling. Steadystate thermal analysis, incorporating LN$_{2}$ convective cooling coefficients and the anisotropic thermal properties of epoxyimpregnated windings, predicts operating temperature distributions and establishes safe current density limits. Numerical case studies for an aluminum armature and NI-HTS coils submerged in LN$_{2}$ show a torque output of 15N$\cdot$ m at an armature current density of 20 A/mm$^{2}$ (RMS), with a thermal limit of 31 A/mm$^{2}$ (RMS) before thermal runaway. The proposed design approach effectively balances electromagnetic performance and thermal management, which serves as a foundation for subsequent experimental validation and prototype development of cryogenic motor systems utilizing NI-HTS field windings.
- 23 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Electromagnetic-Thermal Design and Analysis of Liquid Nitrogen Immersed Aluminum Armature With NI HTS Field Windings
This paper presents an electromagnetic and thermal design methodology for a liquid-nitrogen (LN $_{2}$)-immersed aluminum armature with noinsulation hightemperature superconducting (NIHTS) field windings. A three-dimensional finite-element model is developed to optimize both the armature geometry and the NI-HTS coil configuration. The analysis evaluates key electromagnetic performance metrics, including torque density and electromagnetic coupling. Steadystate thermal analysis, incorporating LN$_{2}$ convective cooling coefficients and the anisotropic thermal properties of epoxyimpregnated windings, predicts operating temperature distributions and establishes safe current density limits. Numerical case studies for an aluminum armature and NI-HTS coils submerged in LN$_{2}$ show a torque output of 15N$\cdot$ m at an armature current density of 20 A/mm$^{2}$ (RMS), with a thermal limit of 31 A/mm$^{2}$ (RMS) before thermal runaway. The proposed design approach effectively balances electromagnetic performance and thermal management, which serves as a foundation for subsequent experimental validation and prototype development of cryogenic motor systems utilizing NI-HTS field windings.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Numerical Study on Screening Current Induced Stress of Dry-Wound HTS Racetrack Coil
This study presents a mechanical stress analysis of a dry-wound high-temperature superconducting (HTS) racetrack coil, focusing on the effects of screening current-induced stress (SCS). A three-dimensional (3D) H-formulation was used to simulate the nonlinear current distribution caused by screening current. A modified method was applied to enforce the total current in the cross-section without having to introduce cross-sectional subdivisions separated by highly resistive layers, as required in conventional models. The coil domain was not divided into subdomains, resulting in a more continuous current distribution. The resulting Lorentz force density was used in a 3D mechanical model with turn-to-turn contact conditions to represent the dry-wound racetrack coil. The analysis showed that screening current caused both the typical expansion of the straight sections and additional tilting deformation, increasing the peak stress by 23.6%. Lastly, the three-dimensional analysis results of the racetrack coil SCS were compared with those obtained from a two-dimensional analysis based on the plane stress assumption.
- 21 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Numerical Study on Screening Current Induced Stress of Dry-Wound HTS Racetrack Coil
This study presents a mechanical stress analysis of a dry-wound high-temperature superconducting (HTS) racetrack coil, focusing on the effects of screening current-induced stress (SCS). A three-dimensional (3D) H-formulation was used to simulate the nonlinear current distribution caused by screening current. A modified method was applied to enforce the total current in the cross-section without having to introduce cross-sectional subdivisions separated by highly resistive layers, as required in conventional models. The coil domain was not divided into subdomains, resulting in a more continuous current distribution. The resulting Lorentz force density was used in a 3D mechanical model with turn-to-turn contact conditions to represent the dry-wound racetrack coil. The analysis showed that screening current caused both the typical expansion of the straight sections and additional tilting deformation, increasing the peak stress by 23.6%. Lastly, the three-dimensional analysis results of the racetrack coil SCS were compared with those obtained from a two-dimensional analysis based on the plane stress assumption.
- 19 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Design, Construction, and Experiment of Roller Shaped High-Temperature Superconducting Coil Joint Apparatus
The fabrication of high-temperature superconductor (HTS) magnets often involves manual soldering joints, which relies on operator skill and causes performance variations. To address these challenges, this study presents the design, construction, and experimental evaluation of a roller-shaped HTS coil joint apparatus for soldering rare-earth barium copper oxide (REBCO) tapes. The apparatus was developed to facilitate the soldering process across various coil dimensions, ensuring high performance and reliable joints between HTS coils. First, simulations and analyses were conducted to ensure the thermal and mechanical requirements based on prior REBCO tape-to-tape joint researches. The apparatus is equipped with functionalities to control parameters such as solder type, target temperature, heating rate, holding time, cooling time, and pressure. Then, the constructed joint apparatus was primarily utilized to validate the tape-to-tape soldering process, with a focus on maintaining consistent electro-mechanical performance. Finally, experimental evaluations of HTS coil-to-coil joints evaluations demonstrated the ability to achieve high performance and reliability joint, highlighting its potential for applications in advanced HTS REBCO magnet systems.
- 19 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Design, Construction, and Experiment of Roller Shaped High-Temperature Superconducting Coil Joint Apparatus
The fabrication of high-temperature superconductor (HTS) magnets often involves manual soldering joints, which relies on operator skill and causes performance variations. To address these challenges, this study presents the design, construction, and experimental evaluation of a roller-shaped HTS coil joint apparatus for soldering rare-earth barium copper oxide (REBCO) tapes. The apparatus was developed to facilitate the soldering process across various coil dimensions, ensuring high performance and reliable joints between HTS coils. First, simulations and analyses were conducted to ensure the thermal and mechanical requirements based on prior REBCO tape-to-tape joint researches. The apparatus is equipped with functionalities to control parameters such as solder type, target temperature, heating rate, holding time, cooling time, and pressure. Then, the constructed joint apparatus was primarily utilized to validate the tape-to-tape soldering process, with a focus on maintaining consistent electro-mechanical performance. Finally, experimental evaluations of HTS coil-to-coil joints evaluations demonstrated the ability to achieve high performance and reliability joint, highlighting its potential for applications in advanced HTS REBCO magnet systems.
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental Study on Temperature-Controlled Charging Sequence for Reduction of Screening Current Effect in HTS Magnet
High-temperature superconductor (HTS) rare-earth barium copper oxide (REBCO) conductor has been extensively researched and developed for various applications. However, due to the intrinsic properties of REBCO conductors, the screening current occurs and this effect causes induced field and stress in superconducting magnets. Therefore, we investigated a strategy to mitigate the screening current effect in HTS magnets with the simultaneous control of temperature and current. In this paper, we ramped up the coil and measured the magnetic field of the HTS magnet as a references on conduction cooling system within different temperature: 20 K and 50 K. Then, the temperature-controlled charging sequence method with PID control was conducted so that the current ramping up simultaneously started with the magnet cool down: (1) 50 K to 20 K and (2) 80 K to 50 K. Finally, we analyzed the experiment results of the magnetic field distribution compared to reference charging values. These results showed the possibility to develop the operating techniques for high-field REBCO magnets that reduce the screening current induced field.
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental Study on Temperature-Controlled Charging Sequence for Reduction of Screening Current Effect in HTS Magnet
High-temperature superconductor (HTS) rare-earth barium copper oxide (REBCO) conductor has been extensively researched and developed for various applications. However, due to the intrinsic properties of REBCO conductors, the screening current occurs and this effect causes induced field and stress in superconducting magnets. Therefore, we investigated a strategy to mitigate the screening current effect in HTS magnets with the simultaneous control of temperature and current. In this paper, we ramped up the coil and measured the magnetic field of the HTS magnet as a references on conduction cooling system within different temperature: 20 K and 50 K. Then, the temperature-controlled charging sequence method with PID control was conducted so that the current ramping up simultaneously started with the magnet cool down: (1) 50 K to 20 K and (2) 80 K to 50 K. Finally, we analyzed the experiment results of the magnetic field distribution compared to reference charging values. These results showed the possibility to develop the operating techniques for high-field REBCO magnets that reduce the screening current induced field.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Design Study of Fully Superconducting Motor With MgB$_{2}$ Wire and YBCO Bulk Combination for Brushless Operation
In response to increasing environmental regulations and the push towards electrification, superconducting motors have gained significant interest due to their high power density potential. This paper presents the design and analysis of a conceptual fully superconducting brushless motor featuring MgB$_{2}$ armature windings and YBCO bulk superconductors in the rotor. The proposed motor utilizes post-assembly magnetization using field cooling, achieving a trapped magnetic field exceeding 2 T. Through optimization and magnetization analysis, the YBCO bulk-type designed motor calculated a 61% improvement in power density compared to a permanent magnet-type designed motor. The design also shows thermal losses of 1.58 kW, which can be effectively covered using LH$_{2}$ cooling. These results present the feasibility of a high-performance, brushless design with HTS bulk field magnets, paving the way for relatively compact cryogenic motor applications.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Design Study of Fully Superconducting Motor With MgB$_{2}$ Wire and YBCO Bulk Combination for Brushless Operation
In response to increasing environmental regulations and the push towards electrification, superconducting motors have gained significant interest due to their high power density potential. This paper presents the design and analysis of a conceptual fully superconducting brushless motor featuring MgB$_{2}$ armature windings and YBCO bulk superconductors in the rotor. The proposed motor utilizes post-assembly magnetization using field cooling, achieving a trapped magnetic field exceeding 2 T. Through optimization and magnetization analysis, the YBCO bulk-type designed motor calculated a 61% improvement in power density compared to a permanent magnet-type designed motor. The design also shows thermal losses of 1.58 kW, which can be effectively covered using LH$_{2}$ cooling. These results present the feasibility of a high-performance, brushless design with HTS bulk field magnets, paving the way for relatively compact cryogenic motor applications.
- 13 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Transient Analysis of Flux Weakening Operation for Synchronous Motor Considering NI HTS Field Coil Behaviors
In the case of a synchronous motor with armature input voltage limitation, flux weakening operation is performed to reduce the magnetic flux generated from the rotor for increasing the rotating speed greater than rated speed. However, in the case of a motor with a no-insulation (NI) HTS field winding, a discharging delay occurs due to radial leakage current when the operating current is lowered, and a motor control delay is generated in following the rotor magnetic flux and rotating speed reference command during flux weakening control. In this paper, in order to analyze the behaviors of the NI HTS field coil during field weakening operation, a dq-equivalent circuit-based transient analysis is performed. The following key aspects are discussed: (1) rotating speed response characteristics; (2) contact resistivity dependency on flux weakening control and (3) active control method of field winding current for mitigating motor speed variation delay.
- 13 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Transient Analysis of Flux Weakening Operation for Synchronous Motor Considering NI HTS Field Coil Behaviors
In the case of a synchronous motor with armature input voltage limitation, flux weakening operation is performed to reduce the magnetic flux generated from the rotor for increasing the rotating speed greater than rated speed. However, in the case of a motor with a no-insulation (NI) HTS field winding, a discharging delay occurs due to radial leakage current when the operating current is lowered, and a motor control delay is generated in following the rotor magnetic flux and rotating speed reference command during flux weakening control. In this paper, in order to analyze the behaviors of the NI HTS field coil during field weakening operation, a dq-equivalent circuit-based transient analysis is performed. The following key aspects are discussed: (1) rotating speed response characteristics; (2) contact resistivity dependency on flux weakening control and (3) active control method of field winding current for mitigating motor speed variation delay.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Post-Quench Analysis and Mechanical Considerations for No-Insulation HTS Racetrack Field Coils in a 5 MW Superconducting Motor
High-power-density superconducting motors are essential for the electrification of transportation systems. High-temperature superconducting (HTS) motors with no-insulation (NI) windings have advantages in achieving high current density, stability, and protection. In this paper, a 5 MW motor is designed, featuring high-energy NI HTS field coils. A post-quench analysis was conducted to investigate its characteristics. Considering critical current and mutual inductance, a lumped circuit model was used to simulate the quench. Thermal modeling was performed to evaluate the temperature rise. Simulation results show an azimuthal overcurrent of 130% of the operating current and a temperature rise of 117 K. Stress analysis for each racetrack coil was conducted, revealing a maximum hoop stress of 882 MPa, which can lead to the degradation of the critical current. To reinforce the racetrack coils, the required preload was calculated, reducing the stress to 463 MPa.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Post-Quench Analysis and Mechanical Considerations for No-Insulation HTS Racetrack Field Coils in a 5 MW Superconducting Motor
High-power-density superconducting motors are essential for the electrification of transportation systems. High-temperature superconducting (HTS) motors with no-insulation (NI) windings have advantages in achieving high current density, stability, and protection. In this paper, a 5 MW motor is designed, featuring high-energy NI HTS field coils. A post-quench analysis was conducted to investigate its characteristics. Considering critical current and mutual inductance, a lumped circuit model was used to simulate the quench. Thermal modeling was performed to evaluate the temperature rise. Simulation results show an azimuthal overcurrent of 130% of the operating current and a temperature rise of 117 K. Stress analysis for each racetrack coil was conducted, revealing a maximum hoop stress of 882 MPa, which can lead to the degradation of the critical current. To reinforce the racetrack coils, the required preload was calculated, reducing the stress to 463 MPa.
- 23 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental and Numerical Analysis on Non-Uniform Current Distribution in Two-Tape Co-Wound HTS Coil
In coils composed of stacked no-insulation (NI) high temperature superconductor (HTS) tapes, the current flow patterns can significantly differ from transposed counterparts due to larger self/mutual inductances and contact resistances. In this study, three two-tape co-wound HTS coils are wound with different insulation methods, fully insulated, NI, and partially insulated. The charging test is performed and the experimental results are analyzed by observing the voltage ratio of two tapes. The voltage ratios show deviations from the theoretical inductive voltage ratios implying uneven current distribution between the tapes. A numerical analysis is carried out with a simulation model that couples the distributed circuit model with the finite element method model to understand these phenomena. Using the model, sensitivity analysis is adopted to explain quantitatively the contributions of each circuit parameter to non-uniform current distribution. Pinpointing the precise current distribution between tapes is challenging, yet experimental and numerical analysis results show certain tendencies influenced by inductive and resistive properties.
- 23 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Experimental and Numerical Analysis on Non-Uniform Current Distribution in Two-Tape Co-Wound HTS Coil
In coils composed of stacked no-insulation (NI) high temperature superconductor (HTS) tapes, the current flow patterns can significantly differ from transposed counterparts due to larger self/mutual inductances and contact resistances. In this study, three two-tape co-wound HTS coils are wound with different insulation methods, fully insulated, NI, and partially insulated. The charging test is performed and the experimental results are analyzed by observing the voltage ratio of two tapes. The voltage ratios show deviations from the theoretical inductive voltage ratios implying uneven current distribution between the tapes. A numerical analysis is carried out with a simulation model that couples the distributed circuit model with the finite element method model to understand these phenomena. Using the model, sensitivity analysis is adopted to explain quantitatively the contributions of each circuit parameter to non-uniform current distribution. Pinpointing the precise current distribution between tapes is challenging, yet experimental and numerical analysis results show certain tendencies influenced by inductive and resistive properties.