BDBoxin Dai

Boxin Dai

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Boxin Dai has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • An Integrated Multiphysics Simulation Framework for Electron Optical Systems: Application to a Compact Ka-Band Gyro-TWT

    by Boxin Dai, Wei Jiang, Mimi Qin, Jianwei Zhou, Binyang Han, Yelei Yao, Zewei Wu, Guo Liu, Jianxun Wang, Yong Luo

    In this article, an integrated multiphysics simulation framework for the electron optical system (EOS) of gyrotron traveling wave tubes (gyro-TWTs) is proposed. By consolidating magnetostatic, beam trajectory, and thermal analysis into a single platform, this method eliminates the inefficiency of switching between disparate commercial software. Additionally, a dedicated EOS database is built to store and reuse previous data, significantly speeding up the design process. To validate the proposed framework, a compact Ka-band TE11 mode gyro-TWT EOS is designed and presented as a verification case. The simulation results agree very well with commercial software. Overall, this in-house framework provides a fast, accurate, and systematic solution for the efficient design of compact gyro-devices.

  • A Microchannel-Enhanced Two-Phase Cooling System for High-Power Ka-Band Sheet Beam Traveling-Wave Tube

    by Binyang Han, Wei Jiang, Boxin Dai, Hongyu Chen, Hao Li, Zewei Wu, Guo Liu, Jianxun Wang, Yong Luo

    The intense and nonuniform heat loads in the interaction circuit of high-power Ka-band sheet beam traveling-wave tubes (SB-TWTs) present significant thermal management challenges for space applications. Traditional single-phase cooling requires high flow velocities and bulky infrastructure and suffers from large temperature fluctuations due to flow nonuniformity and interception randomness. To overcome these limitations, this article proposes a compact R134a-based two-phase cooling system integrated with a novel microchannel-enhanced heat sink unit (HSUM). Numerical analysis demonstrates that the optimized HSUM enables efficient cooling at significantly reduced flow velocities, greatly lowering system mass and volume while maintaining interaction circuit temperatures well below material safety limits with substantially reduced temperature fluctuations compared to single-phase performance. Crucially, the microchannel design stabilizes vapor phase fraction, mitigating vapor-blockage via bubble detachment control predicted in traditional two-phase flow. Bench-scale experiments on a representative circular-channel mock-up under localized heat flux validate the numerical model. This successfully confirmed thermal performance for the HSUM design. This work demonstrates the feasibility of a compact, stable two-phase cooling strategy as an enabling technology for next-generation spaceborne high-power SB-TWTs.

  • Application of Distributed Copper Foam Channels in Ka-Band Megawatt-Class Gyro-TWT Collector

    by Jianwei Zhou, Qianqian Chen, Wei Jiang, Binyang Han, Chaoxuan Lu, Boxin Dai, Guo Liu, Zewei Wu, Ran Yan, Jianxun Wang, et al.

    The thermal management presents a critical challenge in the design of megawatt-class vacuum electronic devices (VEDs). This article introduces distributed copper foam channels (DCFCs) technology, which integrates the metallic porous media renowned for their high-heat dissipation area, notable thermal conductivity, and enhanced flow mixing capability. These copper foam structures are strategically embedded in the flow channels, resulting in a significant improvement in cooling performance. This technique has been implemented in the collector of a Ka-band megawatt-class gyrotron traveling wave tube (gyro-TWT). Transient simulations show that the collector can sustain a peak power density of 9.8 kW/cm2 while maintaining a peak temperature below the $350~{^{\circ }}$ C limit. These improvements enable the collector to achieve a power capacity of 750 kW without increasing its current volume, representing a 100% increase compared with a conventional collector. Moreover, the experimental validation was conducted for both conventional channels and DCFCs using a 2-D mock-up, and the experimental results agreed well with the simulations. These results represent a significant advancement in integrating high-performance coolers into VEDs, potentially enabling applications currently constrained by thermal limitations.

  • Optimization of magnetron injection gun and multi-coil collector design for 170 GHz gyrotron

    by Jin Han, Yinghui Liu, Feng Luo, Hongyang Guo, Boxin Dai, Kai Jia, Zongzheng Sun, Xinjian Niu

    As gyrotrons progress into the millimeter wave range, electron energy reaches the MW level, requiring advanced electron optical systems (EOS) to address electron velocity spread and collector thermal load challenges. This study introduces a continuously curved anode structure that smooths the spatial variation of the electric field magnitude, reduces transverse velocity spread, and enhances beam quality through improved electric-magnetic field matching. To reduce the thermal load on the collector, compensation coils carrying direct current are wound around its outer wall. Simulations of configurations with 1, 5, and 9 coils show that the 9-coil setup, combined with the residual superconducting field, forms an extended uniform magnetic region, adjusting the electron orbit radius to match the collector’s inner radius. This alignment reduces the collision angle between electron trajectories and the collector wall, effectively expands the electron landing range, and reduces local power density. At a spent beam power of 2.925 MW—equal to the electron beam input power in the absence of RF interaction—the electron impact length extends from 46 to 1001.3 mm, and the peak collision power density drops by 93.7%, from 7869.6 to 494.6 W/cm2. These results demonstrate that the proposed multi-coil magnetic topology effectively overcomes heat dissipation limitations, ensuring stable operation of high-power gyrotrons and providing a promising solution for EOS design in millimeter-wave radiation sources.

  • Investigation of Fluid and Thermal Analysis in the Interaction Circuit for Ka-Band Sheet Beam Traveling Wave Tube

    by Binyang Han, Wei Jiang, Chaoxuan Lu, Boxin Dai, Jianwei Zhou, Hongyu Chen, Hao Li, Zewei Wu, Guo Liu, Jianxun Wang, et al.

    Achieving perfect sheet beam transmission through the interaction circuit remains a critical challenge in the sheet beam traveling wave tube (SB-TWT). Particle-in-cell (PIC) simulations reveal that electron interception predominantly concentrates at the terminal region of the interaction circuit, generating highly localized heat fluxes. This nonuniform power density induces temperature spikes (>350 ∘C) and vacuum degradation due to outgassing, necessitating advanced thermal management strategies. This article proposes a novel embedded heat sink unit (EHSU) for Ka-band SB-TWTs, which integrates a staggered grid structure of the interaction circuit and boundary layer suppression to address localized overheating. A model of the heat sink unit, as well as its thermal resistance network was constructed and analyzed for its thermal and fluid behavior. The EHSU framework resulted in a maximum temperature reduction of about 40%. The prototype was fabricated, and the hot test showed it operated stably for long periods of time at an average power of 3 kW. The titanium pump current (Ti-current) was stabilized at approximately 60 nA for over an hour.


  • Open Access

    Investigation of a planar dual-beam magnetron injection gun for a Ka-band megawatt-class Gyro-TWT

    by Qingjie Yang, Xin Chen, Wei Jiang, Yelei Yao, Chaoxuan Lu, Boxin Dai, Yongdong Cheng, Guo Liu, Jianxun Wang, Yong Luo

    In order to enhance the power capacity of gyro-traveling wave tube (Gyro-TWT), a planar dual-beam magnetron injection gun for a Ka-band Gyro-TWT is proposed. Diocotron instability and transverse inhomogeneity of planar helical electron beam (HEB) are analyzed. To control the trajectory of the electron beam and optimize its performance, an angular drift compensation method and an electric field matching method are designed according to the characteristics of the planar electron beam. The planar HEB (30 × 2 mm), with a pitch factor of 1.4, and a total transverse velocity spread of 3.33%, is obtained. Its electron energy is 60 keV, and the total current is 50 A. The simulation results of beam–wave interaction show that the device has a pulsed power of 1.02 MW at 34 GHz, with an efficiency of 34% and a saturated gain of 45.03 dB. The 3 dB bandwidth is 2.4 GHz. This design provides a possible method for the development of Gyro-TWTs with megawatt output power.


  • High-Power 100 kW CW Q-Band Gyro-TWT: Performance and Stability

    by Wei Jiang, Chaoxuan Lu, Jianwei Zhou, Yafen Shang, Qiang Zheng, Boxin Dai, Guo Liu, Jianxun Wang, Yelei Yao, Yong Luo

    To satisfy the demand for high-power microwave sources, a Q-band 100 kW continuous-wave (CW) gyrotron traveling wave tube (gyro-TWT) is fabricated and experimentally demonstrated in this letter. The stability and uniformity of electron emission are greatly improved through the application of cathode coating thin-film technology. The power capacity of the device is assessed using efficient thermal management methods. Experimental results show that the gyro-TWT, driven by a 56 kV-7.9 A electron beam, achieves a maximum CW power of 115.6 kW, a gain of 54.9 dB, and an efficiency of 26.1% at 49.5 GHz. The device operates stably for a long time, with performance at the forefront of current technology.


  • Investigation of a Magnetron Injection Gun With an External Anode for Ka-Band Gyro-TWT

    by Boxin Dai, Wei Jiang, Binyang Han, Chaoxuan Lu, Yelei Yao, Zewei Wu, Jianwei Zhou, Guo Liu, Jianxun Wang, Yong Luo

    In this article, a diode magnetron injection gun (MIG) with an external anode for Ka-band gyrotron traveling wave tubes (gyro-TWTs) is designed, whose anode is demountable. The magnet bore radius constrains the maximum radius of an MIG. To adapt to a magnet with smaller bore radius, a compact MIG with smaller radial size is necessary. Compared to the previous conventional Ka-band MIG, the gun effective radius constrained by the magnet bore is reduced from 35 to 19.5 mm, which is a 44% reduction. For a better high-voltage insulation performance of the MIG, studies are conducted on its three-layer dielectric separately: corrugated ceramic is used between the cathode and the anode, and the external anode is immersed in insulating oil. Additionally, a capture structure is designed to suppress backflow electrons. The velocity ratio and transverse velocity spread of the final MIG are 1.36% and 2.19%, respectively. Due to the replaceability of its anode, the MIG has potential for application in multiband or pulsed-continuous wave gyro-TWT operations. To verify the high-voltage stability of the MIG with an external anode, a high-voltage insulation experiment is carried out. The experiment reveals that no breakdown occurs at the operating voltage of 48 kV in the MIG.


  • Open Access

    Design and experiment of an inverse magnetron injection gun for a Ka-band gyro-TWT with non-superconducting magnet

    by Boxin Dai, Yelei Yao, Wei Jiang, Binyang Han, Chaoxuan Lu, Guo Liu, Zewei Wu, Xinge Dai, Jinhuan Chen, Jianxun Wang, et al.

    A triode inverse magnetron injection gun (IMIG) for a Ka-band gyrotron traveling wave tube (gyro-TWT) with non-superconducting magnet is proposed in this paper. Nowadays, the applications of gyro-TWT are intended to expand to moveable and fast-startup systems, so room-temperature magnet and system miniaturization are necessary. For a Ka-band gyro-TWT, to adapt to a room-temperature magnet with 20 mm bore radius, the IMIG form is adopted. Compared with conventional MIG, the gun maximum radius is reduced by 44%. On one hand, a curved emitter and cathode steps are utilized for better beam quality. On the other hand, isolation gaps and a cooling structure are designed to suppress stray electrons. A velocity ratio of 1.14 and a transverse velocity spread of 2.43% are obtained finally. The stray electrons are analyzed, and the IMIG tolerance is also evaluated. Finally, the cathode is fabricated, and its surface morphology is tested. It is then assembled into a gun shell, and the cathode temperatures are measured under both no cooling and cooling conditions. When the temperature of the emitter reaches 1050 °C, the heat powers are 84 and 115 W, respectively. The temperatures of the inner and outer electrodes are low enough to reduce the proportion of stray electrons.


  • Experimental Investigation on Trapped Electrons Oscillation Suppression for W-Band Gyro-TWT

    by Binyang Han, Wei Jiang, Jianxun Wang, Chaoxuan Lu, Boxin Dai, Yelei Yao, Guo Liu, Jianhua Xu, Yong Luo

    The fluctuation of current can destroy the performance of the gyrotron traveling-wave tube (Gyro-TWT). We found that the fluctuation of the current is related to the generation of trapped electrons in the interaction circuit. Through experimental and simulation verification, it has been found that the oscillation characteristics of the current are consistent with the motion characteristics of the trapped electrons in the interaction circuit. This indicates that trapped electrons have a significant impact on the current. To suppress the trapped electrons, a novel magnetron injection gun (MIG) with the rear electrode (MSRE) has been designed. The absorbed power of the interaction circuit has decreased by 50%. When a W-band Gyro-TWT with MSRE is operated at 60.5 kV/10.15 A, zero drive with a pulse duration of $200~\mu $ s, and a duty cycle of 15%, there is no current fluctuation. The tube achieves a peak power of 136 kW, a gain of 71 dB, and an average power of 20.54 kW at 94 GHz. The hot test shows that MSRE can suppress the generation of trapped electrons. This greatly enhances the stability of the tube.