Binyang Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Binyang Han has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Guo Liu
University of Electronic Science and Technology of China
12 shared publications - Jianxun Wang
University of Electronic Science and Technology of China
12 shared publications - Wei Jiang
University of Electronic Science and Technology of China
12 shared publications Yong Luo
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
12 shared publications- Chaoxuan Lu
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
10 shared publications - Boxin Dai
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
9 shared publications
Latest Publications
- 16 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3844-3850
An Integrated Multiphysics Simulation Framework for Electron Optical Systems: Application to a Compact Ka-Band Gyro-TWT
In this article, an integrated multiphysics simulation framework for the electron optical system (EOS) of gyrotron traveling wave tubes (gyro-TWTs) is proposed. By consolidating magnetostatic, beam trajectory, and thermal analysis into a single platform, this method eliminates the inefficiency of switching between disparate commercial software. Additionally, a dedicated EOS database is built to store and reuse previous data, significantly speeding up the design process. To validate the proposed framework, a compact Ka-band TE11 mode gyro-TWT EOS is designed and presented as a verification case. The simulation results agree very well with commercial software. Overall, this in-house framework provides a fast, accurate, and systematic solution for the efficient design of compact gyro-devices.
- 16 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3844-3850
An Integrated Multiphysics Simulation Framework for Electron Optical Systems: Application to a Compact Ka-Band Gyro-TWT
In this article, an integrated multiphysics simulation framework for the electron optical system (EOS) of gyrotron traveling wave tubes (gyro-TWTs) is proposed. By consolidating magnetostatic, beam trajectory, and thermal analysis into a single platform, this method eliminates the inefficiency of switching between disparate commercial software. Additionally, a dedicated EOS database is built to store and reuse previous data, significantly speeding up the design process. To validate the proposed framework, a compact Ka-band TE11 mode gyro-TWT EOS is designed and presented as a verification case. The simulation results agree very well with commercial software. Overall, this in-house framework provides a fast, accurate, and systematic solution for the efficient design of compact gyro-devices.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 3036-3042
A Microchannel-Enhanced Two-Phase Cooling System for High-Power Ka-Band Sheet Beam Traveling-Wave Tube
The intense and nonuniform heat loads in the interaction circuit of high-power Ka-band sheet beam traveling-wave tubes (SB-TWTs) present significant thermal management challenges for space applications. Traditional single-phase cooling requires high flow velocities and bulky infrastructure and suffers from large temperature fluctuations due to flow nonuniformity and interception randomness. To overcome these limitations, this article proposes a compact R134a-based two-phase cooling system integrated with a novel microchannel-enhanced heat sink unit (HSUM). Numerical analysis demonstrates that the optimized HSUM enables efficient cooling at significantly reduced flow velocities, greatly lowering system mass and volume while maintaining interaction circuit temperatures well below material safety limits with substantially reduced temperature fluctuations compared to single-phase performance. Crucially, the microchannel design stabilizes vapor phase fraction, mitigating vapor-blockage via bubble detachment control predicted in traditional two-phase flow. Bench-scale experiments on a representative circular-channel mock-up under localized heat flux validate the numerical model. This successfully confirmed thermal performance for the HSUM design. This work demonstrates the feasibility of a compact, stable two-phase cooling strategy as an enabling technology for next-generation spaceborne high-power SB-TWTs.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 3036-3042
A Microchannel-Enhanced Two-Phase Cooling System for High-Power Ka-Band Sheet Beam Traveling-Wave Tube
The intense and nonuniform heat loads in the interaction circuit of high-power Ka-band sheet beam traveling-wave tubes (SB-TWTs) present significant thermal management challenges for space applications. Traditional single-phase cooling requires high flow velocities and bulky infrastructure and suffers from large temperature fluctuations due to flow nonuniformity and interception randomness. To overcome these limitations, this article proposes a compact R134a-based two-phase cooling system integrated with a novel microchannel-enhanced heat sink unit (HSUM). Numerical analysis demonstrates that the optimized HSUM enables efficient cooling at significantly reduced flow velocities, greatly lowering system mass and volume while maintaining interaction circuit temperatures well below material safety limits with substantially reduced temperature fluctuations compared to single-phase performance. Crucially, the microchannel design stabilizes vapor phase fraction, mitigating vapor-blockage via bubble detachment control predicted in traditional two-phase flow. Bench-scale experiments on a representative circular-channel mock-up under localized heat flux validate the numerical model. This successfully confirmed thermal performance for the HSUM design. This work demonstrates the feasibility of a compact, stable two-phase cooling strategy as an enabling technology for next-generation spaceborne high-power SB-TWTs.
- 18 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 3017-3022
Application of Distributed Copper Foam Channels in Ka-Band Megawatt-Class Gyro-TWT Collector
The thermal management presents a critical challenge in the design of megawatt-class vacuum electronic devices (VEDs). This article introduces distributed copper foam channels (DCFCs) technology, which integrates the metallic porous media renowned for their high-heat dissipation area, notable thermal conductivity, and enhanced flow mixing capability. These copper foam structures are strategically embedded in the flow channels, resulting in a significant improvement in cooling performance. This technique has been implemented in the collector of a Ka-band megawatt-class gyrotron traveling wave tube (gyro-TWT). Transient simulations show that the collector can sustain a peak power density of 9.8 kW/cm2 while maintaining a peak temperature below the $350~{^{\circ }}$ C limit. These improvements enable the collector to achieve a power capacity of 750 kW without increasing its current volume, representing a 100% increase compared with a conventional collector. Moreover, the experimental validation was conducted for both conventional channels and DCFCs using a 2-D mock-up, and the experimental results agreed well with the simulations. These results represent a significant advancement in integrating high-performance coolers into VEDs, potentially enabling applications currently constrained by thermal limitations.
- 18 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 3017-3022
Application of Distributed Copper Foam Channels in Ka-Band Megawatt-Class Gyro-TWT Collector
The thermal management presents a critical challenge in the design of megawatt-class vacuum electronic devices (VEDs). This article introduces distributed copper foam channels (DCFCs) technology, which integrates the metallic porous media renowned for their high-heat dissipation area, notable thermal conductivity, and enhanced flow mixing capability. These copper foam structures are strategically embedded in the flow channels, resulting in a significant improvement in cooling performance. This technique has been implemented in the collector of a Ka-band megawatt-class gyrotron traveling wave tube (gyro-TWT). Transient simulations show that the collector can sustain a peak power density of 9.8 kW/cm2 while maintaining a peak temperature below the $350~{^{\circ }}$ C limit. These improvements enable the collector to achieve a power capacity of 750 kW without increasing its current volume, representing a 100% increase compared with a conventional collector. Moreover, the experimental validation was conducted for both conventional channels and DCFCs using a 2-D mock-up, and the experimental results agreed well with the simulations. These results represent a significant advancement in integrating high-performance coolers into VEDs, potentially enabling applications currently constrained by thermal limitations.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (8) , 4440-4445
Investigation of Fluid and Thermal Analysis in the Interaction Circuit for Ka-Band Sheet Beam Traveling Wave Tube
Achieving perfect sheet beam transmission through the interaction circuit remains a critical challenge in the sheet beam traveling wave tube (SB-TWT). Particle-in-cell (PIC) simulations reveal that electron interception predominantly concentrates at the terminal region of the interaction circuit, generating highly localized heat fluxes. This nonuniform power density induces temperature spikes (>350 ∘C) and vacuum degradation due to outgassing, necessitating advanced thermal management strategies. This article proposes a novel embedded heat sink unit (EHSU) for Ka-band SB-TWTs, which integrates a staggered grid structure of the interaction circuit and boundary layer suppression to address localized overheating. A model of the heat sink unit, as well as its thermal resistance network was constructed and analyzed for its thermal and fluid behavior. The EHSU framework resulted in a maximum temperature reduction of about 40%. The prototype was fabricated, and the hot test showed it operated stably for long periods of time at an average power of 3 kW. The titanium pump current (Ti-current) was stabilized at approximately 60 nA for over an hour.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (8) , 4440-4445
Investigation of Fluid and Thermal Analysis in the Interaction Circuit for Ka-Band Sheet Beam Traveling Wave Tube
Achieving perfect sheet beam transmission through the interaction circuit remains a critical challenge in the sheet beam traveling wave tube (SB-TWT). Particle-in-cell (PIC) simulations reveal that electron interception predominantly concentrates at the terminal region of the interaction circuit, generating highly localized heat fluxes. This nonuniform power density induces temperature spikes (>350 ∘C) and vacuum degradation due to outgassing, necessitating advanced thermal management strategies. This article proposes a novel embedded heat sink unit (EHSU) for Ka-band SB-TWTs, which integrates a staggered grid structure of the interaction circuit and boundary layer suppression to address localized overheating. A model of the heat sink unit, as well as its thermal resistance network was constructed and analyzed for its thermal and fluid behavior. The EHSU framework resulted in a maximum temperature reduction of about 40%. The prototype was fabricated, and the hot test showed it operated stably for long periods of time at an average power of 3 kW. The titanium pump current (Ti-current) was stabilized at approximately 60 nA for over an hour.
- Open Access
- 1 June 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (6)
Design of an three-stage elliptical depressed collector for a sheet beam Ka-band TWT
Sheet electron beam vacuum electronic devices have gained significant research attention due to their high power and high frequency. Previous studies of the collector for the sheet electron beam traveling wave tube (SB-TWT) have primarily focused on single depressed collectors, while little attention has been paid to multi-depressed collectors (MDCs). In this paper, a high-efficiency, low back-streaming, elliptical three-stage depressed collector is designed for a Ka-band TWT operating at 30 kV, 0.9 A, with an output power of 5.2 kW. Before designing the MDC, the energy and velocity distributions and the time-varying trajectory inside the MDC of the spent electron beam are analyzed. The simulation results indicate 90.10% collector efficiency with 0.03% back-streaming in secondary-electron-free conditions, and 82.06% efficiency accompanied by 0.62% back-streaming when considering secondary electron. The simulation, without secondary electrons, demonstrates an improvement in overall efficiency to 70.46%. This article is believed to provide some guidance for the design of MDC of Ka-band TWTs.
- 1 June 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (6)
Open AccessDesign of an three-stage elliptical depressed collector for a sheet beam Ka-band TWT
Sheet electron beam vacuum electronic devices have gained significant research attention due to their high power and high frequency. Previous studies of the collector for the sheet electron beam traveling wave tube (SB-TWT) have primarily focused on single depressed collectors, while little attention has been paid to multi-depressed collectors (MDCs). In this paper, a high-efficiency, low back-streaming, elliptical three-stage depressed collector is designed for a Ka-band TWT operating at 30 kV, 0.9 A, with an output power of 5.2 kW. Before designing the MDC, the energy and velocity distributions and the time-varying trajectory inside the MDC of the spent electron beam are analyzed. The simulation results indicate 90.10% collector efficiency with 0.03% back-streaming in secondary-electron-free conditions, and 82.06% efficiency accompanied by 0.62% back-streaming when considering secondary electron. The simulation, without secondary electrons, demonstrates an improvement in overall efficiency to 70.46%. This article is believed to provide some guidance for the design of MDC of Ka-band TWTs.
- 4 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1448-1454
Investigation of a Magnetron Injection Gun With an External Anode for Ka-Band Gyro-TWT
In this article, a diode magnetron injection gun (MIG) with an external anode for Ka-band gyrotron traveling wave tubes (gyro-TWTs) is designed, whose anode is demountable. The magnet bore radius constrains the maximum radius of an MIG. To adapt to a magnet with smaller bore radius, a compact MIG with smaller radial size is necessary. Compared to the previous conventional Ka-band MIG, the gun effective radius constrained by the magnet bore is reduced from 35 to 19.5 mm, which is a 44% reduction. For a better high-voltage insulation performance of the MIG, studies are conducted on its three-layer dielectric separately: corrugated ceramic is used between the cathode and the anode, and the external anode is immersed in insulating oil. Additionally, a capture structure is designed to suppress backflow electrons. The velocity ratio and transverse velocity spread of the final MIG are 1.36% and 2.19%, respectively. Due to the replaceability of its anode, the MIG has potential for application in multiband or pulsed-continuous wave gyro-TWT operations. To verify the high-voltage stability of the MIG with an external anode, a high-voltage insulation experiment is carried out. The experiment reveals that no breakdown occurs at the operating voltage of 48 kV in the MIG.
- 4 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1448-1454
Investigation of a Magnetron Injection Gun With an External Anode for Ka-Band Gyro-TWT
In this article, a diode magnetron injection gun (MIG) with an external anode for Ka-band gyrotron traveling wave tubes (gyro-TWTs) is designed, whose anode is demountable. The magnet bore radius constrains the maximum radius of an MIG. To adapt to a magnet with smaller bore radius, a compact MIG with smaller radial size is necessary. Compared to the previous conventional Ka-band MIG, the gun effective radius constrained by the magnet bore is reduced from 35 to 19.5 mm, which is a 44% reduction. For a better high-voltage insulation performance of the MIG, studies are conducted on its three-layer dielectric separately: corrugated ceramic is used between the cathode and the anode, and the external anode is immersed in insulating oil. Additionally, a capture structure is designed to suppress backflow electrons. The velocity ratio and transverse velocity spread of the final MIG are 1.36% and 2.19%, respectively. Due to the replaceability of its anode, the MIG has potential for application in multiband or pulsed-continuous wave gyro-TWT operations. To verify the high-voltage stability of the MIG with an external anode, a high-voltage insulation experiment is carried out. The experiment reveals that no breakdown occurs at the operating voltage of 48 kV in the MIG.
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (6) , 3921-3926
Experimental Investigation on Trapped Electrons Oscillation Suppression for W-Band Gyro-TWT
The fluctuation of current can destroy the performance of the gyrotron traveling-wave tube (Gyro-TWT). We found that the fluctuation of the current is related to the generation of trapped electrons in the interaction circuit. Through experimental and simulation verification, it has been found that the oscillation characteristics of the current are consistent with the motion characteristics of the trapped electrons in the interaction circuit. This indicates that trapped electrons have a significant impact on the current. To suppress the trapped electrons, a novel magnetron injection gun (MIG) with the rear electrode (MSRE) has been designed. The absorbed power of the interaction circuit has decreased by 50%. When a W-band Gyro-TWT with MSRE is operated at 60.5 kV/10.15 A, zero drive with a pulse duration of $200~\mu $ s, and a duty cycle of 15%, there is no current fluctuation. The tube achieves a peak power of 136 kW, a gain of 71 dB, and an average power of 20.54 kW at 94 GHz. The hot test shows that MSRE can suppress the generation of trapped electrons. This greatly enhances the stability of the tube.
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (6) , 3921-3926
Experimental Investigation on Trapped Electrons Oscillation Suppression for W-Band Gyro-TWT
The fluctuation of current can destroy the performance of the gyrotron traveling-wave tube (Gyro-TWT). We found that the fluctuation of the current is related to the generation of trapped electrons in the interaction circuit. Through experimental and simulation verification, it has been found that the oscillation characteristics of the current are consistent with the motion characteristics of the trapped electrons in the interaction circuit. This indicates that trapped electrons have a significant impact on the current. To suppress the trapped electrons, a novel magnetron injection gun (MIG) with the rear electrode (MSRE) has been designed. The absorbed power of the interaction circuit has decreased by 50%. When a W-band Gyro-TWT with MSRE is operated at 60.5 kV/10.15 A, zero drive with a pulse duration of $200~\mu $ s, and a duty cycle of 15%, there is no current fluctuation. The tube achieves a peak power of 136 kW, a gain of 71 dB, and an average power of 20.54 kW at 94 GHz. The hot test shows that MSRE can suppress the generation of trapped electrons. This greatly enhances the stability of the tube.
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (5) , 905-908
Experimental Demonstration of a 10-kW-Level G-Band Gyro-TWT
To satisfy the demand for high-power microwave sources in the terahertz band, a G-band dielectric-load gyro-TWT is fabricated and experimental demonstrated for the first time in this letter. The high-precision assembly and concentricity adjustment technology are proposed to minimize test deviations. The hot test result indicates that the gyro-TWT, driven by a 48.3 kV-3.05 A electron beam with a duty cycle of 10%, achieves a maximum pulse power of 34.1 kW, a gain of 59.8 dB, and an efficiency of 23.2% at 216 GHz. More than 10 kW output power is produced between 213 to 221 GHz. This result represents the highest output power in the terahertz band dielectric-load gyro-TWT currently.
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (5) , 905-908
Experimental Demonstration of a 10-kW-Level G-Band Gyro-TWT
To satisfy the demand for high-power microwave sources in the terahertz band, a G-band dielectric-load gyro-TWT is fabricated and experimental demonstrated for the first time in this letter. The high-precision assembly and concentricity adjustment technology are proposed to minimize test deviations. The hot test result indicates that the gyro-TWT, driven by a 48.3 kV-3.05 A electron beam with a duty cycle of 10%, achieves a maximum pulse power of 34.1 kW, a gain of 59.8 dB, and an efficiency of 23.2% at 216 GHz. More than 10 kW output power is produced between 213 to 221 GHz. This result represents the highest output power in the terahertz band dielectric-load gyro-TWT currently.
- 2 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (11) , 5952-5958
Investigation of a Multi-Gap, High-Voltage Isolator for a Gyro-TWT With Depressed Collector
The depressed collector is an effective approach to further improve the overall efficiency of high-frequency gyrotron traveling wave tubes (gyro-TWTs). In this article, a multi-gap output isolator is proposed. With similar topologies based on the single-gap output isolator, the multi-gap output isolator offers advantages such as high breakdown voltage, improved microwave transmission, and reduced microwave leakage. The Q -band TE $_{\text{01}}$ mode single gap (gap of 2.2 $\times$ 1 mm) and triple gap (gap of 1 $\times$ 3 mm) output isolators are designed and compared in terms of microwave performance and breakdown voltage. Then microwave amplification and beam energy recovery are discussed based on a Q -band gyro-TWT with a triple-gap output isolator. Simulation results demonstrate that when driven by a 60-kV to 9.65-A electron beam, the device can stably produce a maximum output power of 205 and 193 kW of recycled power at 47 GHz with a 20-kV depressed collector. The overall efficiency is effectively increased from 35.4% to 53.1%. The mode converter and triple-gap output isolator are fabricated and experimented. Cold test results show that $\textit{S}_{\text{11}}$ is lower than $-$ 13 dB, $\textit{S}_{\text{21}}$ is greater than $-$ 1.3 dB, and are in good agreement with the simulation results. Furthermore, a maximum breakdown voltage of 70.7 kV is measured in the experiment. These investigations provide ideas for achieving efficient operation of high-frequency gyro-TWTs.
- 2 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (11) , 5952-5958
Investigation of a Multi-Gap, High-Voltage Isolator for a Gyro-TWT With Depressed Collector
The depressed collector is an effective approach to further improve the overall efficiency of high-frequency gyrotron traveling wave tubes (gyro-TWTs). In this article, a multi-gap output isolator is proposed. With similar topologies based on the single-gap output isolator, the multi-gap output isolator offers advantages such as high breakdown voltage, improved microwave transmission, and reduced microwave leakage. The Q -band TE $_{\text{01}}$ mode single gap (gap of 2.2 $\times$ 1 mm) and triple gap (gap of 1 $\times$ 3 mm) output isolators are designed and compared in terms of microwave performance and breakdown voltage. Then microwave amplification and beam energy recovery are discussed based on a Q -band gyro-TWT with a triple-gap output isolator. Simulation results demonstrate that when driven by a 60-kV to 9.65-A electron beam, the device can stably produce a maximum output power of 205 and 193 kW of recycled power at 47 GHz with a 20-kV depressed collector. The overall efficiency is effectively increased from 35.4% to 53.1%. The mode converter and triple-gap output isolator are fabricated and experimented. Cold test results show that $\textit{S}_{\text{11}}$ is lower than $-$ 13 dB, $\textit{S}_{\text{21}}$ is greater than $-$ 1.3 dB, and are in good agreement with the simulation results. Furthermore, a maximum breakdown voltage of 70.7 kV is measured in the experiment. These investigations provide ideas for achieving efficient operation of high-frequency gyro-TWTs.
- 12 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (8) , 4372-4378
Experiment and Power Capacity Investigation of Collector in the 50-kW-Average-Power Q-Band Gyro-TWT
To further increase the average output power of the $\textit{Q}$ -band gyrotron traveling wave tube (gyro-TWT), the power capacity and stability of the collector are investigated. In this article, the characteristics of the electron collection, the modeling of the cooling system, and the suppression of stray electrons are analyzed. The dissipated power is associated with the transverse energy of the electron beam. When the gyro-TWT operates at zero drive, the collector has a maximum dissipated power density of 2 kW/cm $^{\text{2}}$ for a high average power state. Thermal results indicate a maximum temperature of 381 $^{\circ}$ C on the collector with an optimized cooling system. By applying a transverse magnetic field, the stray electrons can be completely intercepted by the collector. The hot experiment results indicate that the gyro-TWT (45% duty cycle), driven by a 60-kV–9.82-A electron beam, can withstand a maximum beam power of 265 kW at zero drive. Then, a pulse power of 111 kW, with an average power of 50 kW and an efficiency of 18.8% at 47 GHz, is measured stably. The simulation and experimental results demonstrate the high-power capacity and high stability of the curved collector.
- 12 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (8) , 4372-4378
Experiment and Power Capacity Investigation of Collector in the 50-kW-Average-Power Q-Band Gyro-TWT
To further increase the average output power of the $\textit{Q}$ -band gyrotron traveling wave tube (gyro-TWT), the power capacity and stability of the collector are investigated. In this article, the characteristics of the electron collection, the modeling of the cooling system, and the suppression of stray electrons are analyzed. The dissipated power is associated with the transverse energy of the electron beam. When the gyro-TWT operates at zero drive, the collector has a maximum dissipated power density of 2 kW/cm $^{\text{2}}$ for a high average power state. Thermal results indicate a maximum temperature of 381 $^{\circ}$ C on the collector with an optimized cooling system. By applying a transverse magnetic field, the stray electrons can be completely intercepted by the collector. The hot experiment results indicate that the gyro-TWT (45% duty cycle), driven by a 60-kV–9.82-A electron beam, can withstand a maximum beam power of 265 kW at zero drive. Then, a pulse power of 111 kW, with an average power of 50 kW and an efficiency of 18.8% at 47 GHz, is measured stably. The simulation and experimental results demonstrate the high-power capacity and high stability of the curved collector.