Siyin Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Siyin Guo has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Qing Zhu
Xidian University
5 shared publications - Xiaohua Ma
Xidian University
5 shared publications - Meng Zhang
Xidian University
4 shared publications - Yilin Chen
School of Advanced Materials and Nanotechnology, Xidian University, Xian, CHINA
4 shared publications - Minhan Mi
School of Microelectronics, Xidian University, Xi’an, China
3 shared publications - Yue Hao
Guangzhou Wide Bandgap Semiconductor Innovation Center, Guangzhou Institute of Technology, Xidian University 1 , Guangzhou 510555
3 shared publications
Latest Publications
- 20 May 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (6) , 065014
Effects of spacer layer thickness in InAlN/GaN double-channel HEMTs
In this paper, the impact of upper channel layer thickness on the electrical characteristics and hysteresis behavior of double-channel InAlN/GaN HEMTs were investigated. The devices with an upper channel layer thickness of 20 nm exhibit higher output current and lower R on compared to devices with a thickness of 10/6 nm. This is attributed to the higher sheet carrier density and the reduced scattering. However, a 20 nm thickness of the upper channel layer in HEMT exhibits hysteresis phenomena in its electrical characteristics. For this hysteresis phenomenon, capacitance measurements and TEM characterization indicate that it is caused by dislocations in the lower barrier layer under the gate. A thicker upper channel layer is beneficial to increasing the output current of the device but leads to degradation of the lower InAlN barrier layer, resulting in hysteresis. This study provides an optimized solution for the growth and device fabrication of double-channel InAlN materials.
- 20 May 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (6) , 065014
Effects of spacer layer thickness in InAlN/GaN double-channel HEMTs
In this paper, the impact of upper channel layer thickness on the electrical characteristics and hysteresis behavior of double-channel InAlN/GaN HEMTs were investigated. The devices with an upper channel layer thickness of 20 nm exhibit higher output current and lower R on compared to devices with a thickness of 10/6 nm. This is attributed to the higher sheet carrier density and the reduced scattering. However, a 20 nm thickness of the upper channel layer in HEMT exhibits hysteresis phenomena in its electrical characteristics. For this hysteresis phenomenon, capacitance measurements and TEM characterization indicate that it is caused by dislocations in the lower barrier layer under the gate. A thicker upper channel layer is beneficial to increasing the output current of the device but leads to degradation of the lower InAlN barrier layer, resulting in hysteresis. This study provides an optimized solution for the growth and device fabrication of double-channel InAlN materials.
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1448-1454
Influence of Transverse Geometry of Sidewall Gates on Characteristics of AlGaN/GaN Fin-HEMTs
This article investigates the influence of transverse geometry of sidewall gates on characteristics of AlGaN/GaN Fin-high-electron-mobility transistors (HEMTs) with rectangular HEMTs (RG-HEMTs), divergent HEMTs (DG-HEMTs), and convergent HEMTs (CG-HEMTs) sidewall gate structure. The subthreshold characteristics of the three types of devices have been compared. The pinch-off voltage of the DG-HEMTs and CG-HEMTs exhibits a slightly positive shift compared to RG-HEMTs, indicating that the pinch-off voltage depended on the smallest nanochannel width in Fin-HEMTs. What’s more, the DG-HEMT exhibits a pronounced depletion effect on channel electrons, and an enhanced gate control capability, improving the threshold voltage stability and suppressing the short-channel effects. At the source side in the channel under the gate, a high electron barrier was been observed in the DG-HEMTs, effectively blocking the injection of carriers from the source into the channel as the drain voltage increased. Additionally, at the corner from the assess region to the channel, the DG-HEMTs displayed the fastest potential rise. The effective electron transport has been enhanced in the channel, making it possible to reach an enhanced electron velocity along most of the channel length, leading to a reduced knee voltage. This conclusion has been validated through simulations of Fin-HEMTs with different channel widths. Furthermore, the DG-HEMT delivers improved DE and PAE at V $_{\text{DC}}$ $=$ 9 V.
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (3) , 1448-1454
Influence of Transverse Geometry of Sidewall Gates on Characteristics of AlGaN/GaN Fin-HEMTs
This article investigates the influence of transverse geometry of sidewall gates on characteristics of AlGaN/GaN Fin-high-electron-mobility transistors (HEMTs) with rectangular HEMTs (RG-HEMTs), divergent HEMTs (DG-HEMTs), and convergent HEMTs (CG-HEMTs) sidewall gate structure. The subthreshold characteristics of the three types of devices have been compared. The pinch-off voltage of the DG-HEMTs and CG-HEMTs exhibits a slightly positive shift compared to RG-HEMTs, indicating that the pinch-off voltage depended on the smallest nanochannel width in Fin-HEMTs. What’s more, the DG-HEMT exhibits a pronounced depletion effect on channel electrons, and an enhanced gate control capability, improving the threshold voltage stability and suppressing the short-channel effects. At the source side in the channel under the gate, a high electron barrier was been observed in the DG-HEMTs, effectively blocking the injection of carriers from the source into the channel as the drain voltage increased. Additionally, at the corner from the assess region to the channel, the DG-HEMTs displayed the fastest potential rise. The effective electron transport has been enhanced in the channel, making it possible to reach an enhanced electron velocity along most of the channel length, leading to a reduced knee voltage. This conclusion has been validated through simulations of Fin-HEMTs with different channel widths. Furthermore, the DG-HEMT delivers improved DE and PAE at V $_{\text{DC}}$ $=$ 9 V.
- 27 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 246-249
Influence of Upper Channel Thickness on InAlN/GaN/InAlN/GaN Double Channel HEMT
HEMTs featuring a double heterostructure (DC-HEMTs) hold considerable promise for diverse applications, owing to their exceptional output characteristics. In this work, the influence of upper channel thickness on carrier distribution and the DC and RF characteristics of the DC-HEMTs was investigated. As the upper channel thickness decreases gradually, the 2-DEG density in the upper channel decreases, while it increases in the lower channel. These result in corresponding variations in transconductance peaks, f T , and f max . Furthermore, the varying effects of drain voltage on carrier concentration in both the upper and lower channels, introduce a novel dimension to the understanding of DC-HEMT characteristics. The observed trends offer crucial considerations for optimizing the design and performance of DC-HEMTs across various applications.
- 27 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 246-249
Influence of Upper Channel Thickness on InAlN/GaN/InAlN/GaN Double Channel HEMT
HEMTs featuring a double heterostructure (DC-HEMTs) hold considerable promise for diverse applications, owing to their exceptional output characteristics. In this work, the influence of upper channel thickness on carrier distribution and the DC and RF characteristics of the DC-HEMTs was investigated. As the upper channel thickness decreases gradually, the 2-DEG density in the upper channel decreases, while it increases in the lower channel. These result in corresponding variations in transconductance peaks, f T , and f max . Furthermore, the varying effects of drain voltage on carrier concentration in both the upper and lower channels, introduce a novel dimension to the understanding of DC-HEMT characteristics. The observed trends offer crucial considerations for optimizing the design and performance of DC-HEMTs across various applications.
- Open Access
- 28 July 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (8) , 1513
Influence of Gate Geometry on the Characteristics of AlGaN/GaN Nanochannel HEMTs for High-Linearity Applications
In this study, AlGaN/GaN nanochannel high-electron-mobility transistors (HEMTs) with tri-gate (TGN-devices) and dual-gate (DGN-devices) structures were fabricated and investigated. It was found that the peak value of the transconductance (Gm), current gain cut-off frequency (fT) and power gain cut-off frequency (fmax) of the TGN-devices were larger than that of the DGN-devices because of the enhanced gate control from the top gate. Although the TGN-devices and DGN-devices demonstrated flattened transconductance, fT and fmax profiles, the first and second transconductance derivatives of the DGN-devices were lower than those of the TGN-devices, implying an improvement in linearity. With the nanochannel width decreased, the peak value of the transconductance and the first and second transconductance derivatives increased, implying the predominant influence of sidewall gate capacitance on the transconductance and linearity. The comparison of gate capacitance for the TGN-devices and DGN-devices revealed that the gate capacitance of the tri-gate structure was not simply a linear superposition of the top planar gate capacitance and sidewall gate capacitance of the dual-gate structure, which could be attributed to the difference in the depletion region shape for tri-gate and dual-gate structures.
- 28 July 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (8) , 1513
Open AccessInfluence of Gate Geometry on the Characteristics of AlGaN/GaN Nanochannel HEMTs for High-Linearity Applications
In this study, AlGaN/GaN nanochannel high-electron-mobility transistors (HEMTs) with tri-gate (TGN-devices) and dual-gate (DGN-devices) structures were fabricated and investigated. It was found that the peak value of the transconductance (Gm), current gain cut-off frequency (fT) and power gain cut-off frequency (fmax) of the TGN-devices were larger than that of the DGN-devices because of the enhanced gate control from the top gate. Although the TGN-devices and DGN-devices demonstrated flattened transconductance, fT and fmax profiles, the first and second transconductance derivatives of the DGN-devices were lower than those of the TGN-devices, implying an improvement in linearity. With the nanochannel width decreased, the peak value of the transconductance and the first and second transconductance derivatives increased, implying the predominant influence of sidewall gate capacitance on the transconductance and linearity. The comparison of gate capacitance for the TGN-devices and DGN-devices revealed that the gate capacitance of the tri-gate structure was not simply a linear superposition of the top planar gate capacitance and sidewall gate capacitance of the dual-gate structure, which could be attributed to the difference in the depletion region shape for tri-gate and dual-gate structures.
- Open Access
- 6 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 72-77
InAlN/GaN HEMT With n+GaN Contact Ledge Structure for Millimeter-Wave Low Voltage Applications
In this work, high performance InAlN/GaN HEMT based on the n+GaN regrown ohmic contact with n+GaN contact ledge structure is proposed. The regrown ohmic contact of InAlN/GaN HEMT is formed by MBE n+GaN regrowth and selfstopping etching, which makes the total ohmic contact resistance between the 2DEG channel and the ohmic metal decrease to 0.12 Ωmm and forms n+GaN contact ledge structure. Owing to the n+GaN contact ledge on the InAlN barrier, with the increasing of drain-source voltage (VDS), an additional current path comes into being between the n+GaN contact ledge on the InAlN barrier and the 2DEG channel, which can “shorten” the device effective drainsource distance, thus further reducing the parasitic resistance. Compared with regrown InAlN/GaN HEMT without n+GaN contact ledge structure, the peak transconductance (Gm.max) of regrown InAlN/GaN HEMT with n+GaN contact ledge structure increases from 747 mS/mm to 874 mS/mm, and the saturation current density (ID.max) increases from 2.6 A/mm to 2.9 A/mm. Besides, the self-stopping etching on the access region does not induce extra defects, and negligible current collapse is obtained. As the results of low parasitic resistance, high output current density, low knee voltage and negligible current collapse, poweradded-efficiency (PAE) of 44% together with output power density (Pout) of 2.5 W/mm is achieved at 30 GHz and VDS of 10 V, which indicates regrown InAlN/GaN HEMT with n+GaN contact ledge structure has great potential for millimeter-wave low voltage applications. Additionally, the transfer and schottky gate characteristics show negligible degradation after OFF/ON-state electrical stress tests.
- 6 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 11, 72-77
Open AccessInAlN/GaN HEMT With n+GaN Contact Ledge Structure for Millimeter-Wave Low Voltage Applications
In this work, high performance InAlN/GaN HEMT based on the n+GaN regrown ohmic contact with n+GaN contact ledge structure is proposed. The regrown ohmic contact of InAlN/GaN HEMT is formed by MBE n+GaN regrowth and selfstopping etching, which makes the total ohmic contact resistance between the 2DEG channel and the ohmic metal decrease to 0.12 Ωmm and forms n+GaN contact ledge structure. Owing to the n+GaN contact ledge on the InAlN barrier, with the increasing of drain-source voltage (VDS), an additional current path comes into being between the n+GaN contact ledge on the InAlN barrier and the 2DEG channel, which can “shorten” the device effective drainsource distance, thus further reducing the parasitic resistance. Compared with regrown InAlN/GaN HEMT without n+GaN contact ledge structure, the peak transconductance (Gm.max) of regrown InAlN/GaN HEMT with n+GaN contact ledge structure increases from 747 mS/mm to 874 mS/mm, and the saturation current density (ID.max) increases from 2.6 A/mm to 2.9 A/mm. Besides, the self-stopping etching on the access region does not induce extra defects, and negligible current collapse is obtained. As the results of low parasitic resistance, high output current density, low knee voltage and negligible current collapse, poweradded-efficiency (PAE) of 44% together with output power density (Pout) of 2.5 W/mm is achieved at 30 GHz and VDS of 10 V, which indicates regrown InAlN/GaN HEMT with n+GaN contact ledge structure has great potential for millimeter-wave low voltage applications. Additionally, the transfer and schottky gate characteristics show negligible degradation after OFF/ON-state electrical stress tests.