Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shiqun Li has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimization of Differentiated Pricing Strategies for Freeways Considering Vehicle Collision Probability

    by Sihui Dong, Xingyu Zhou, Shiqun Li, Yuebiao Zhao

    In response to the limitations of the conventional fixed-rate pricing model for freeways in addressing spatiotemporal imbalances in traffic flow distribution and low road network resource utilization, as well as the neglect of Vehicle Collision probability in existing differentiated pricing frameworks, this study analyzes the underlying relationship between road traffic saturation and collision probability. On this basis, a bi-level programming model for differentiated freeway pricing that explicitly accounts for Vehicle Collision probability is developed. The upper-level model maximizes the economic benefit of freeway operations while incorporating vehicle-collision-probability-related costs, whereas the lower-level model minimizes vehicle travel impedance, including both travel cost and time delays induced by collisions. A hybrid algorithm combining particle swarm optimization (PSO) and pattern search (PS) is employed to solve the optimal pricing scheme across different vehicle types (passenger cars and trucks), road segments, and time periods. A nested Logit model is introduced to characterize travelers’ route choice behavior between alternative routes, thereby capturing the traffic redistribution effect induced by pricing rate adjustments. Empirical data from a section of the Shenyang–Haikou Freeway corridor in China for the year 2024 are used for model calibration and validation. The results indicate that following the optimized pricing scheme, the freeway’s monthly net revenue increased by 9.44%, truck and passenger car traffic volumes rose by 8.59% and 6.12%, respectively, and total segment traffic volume increased by 7.18%. The saturation of the freeway increased from approximately 0.18 to about 0.32, while that of the parallel arterial decreased from approximately 0.9 to about 0.67, indicating a more balanced traffic flow distribution across the network and a substantial reduction in Vehicle Collision probability. These findings demonstrate that the proposed method can effectively balance the trade-offs among operational revenue, traffic efficiency, and driving safety, providing both theoretical support and a quantitative tool for the scientific formulation of differentiated freeway pricing schemes.

  • A multi-phase reliability assessment of EMU braking systems considering common cause failure

    by Xiantao Zhang, Shiqun Li, Yonghua Li, Qing Xia, Zhenliang Fu, Zhengtai Wang

    In the reliability assessment of Electric Multiple Unit (EMU) braking systems, ignoring the multi-phase operational characteristics and common cause failure (CCF) among components may lead to overly conservative assessment results. To address this issue, a multi-phase dynamic Bayesian network (DBN) reliability assessment method considering CCF is proposed. First, components are partitioned into different phases based on the braking system’s operating principles, and a cross-phase conditional state transition mechanism is introduced to construct a multi-phase DBN model. Subsequently, the β -factor model is employed to quantitatively characterize the CCF among components. By using an explicit modeling approach, virtual CCF nodes are embedded into the phase slices of the DBN model, and the conditional state transition probabilities of the associated nodes are adjusted, enabling accurate assessment of system reliability. Finally, the effectiveness of the proposed method is validated using the braking system of a specific CR-series EMU as a case study. The results demonstrate that, compared with the traditional DBN model, the multi-phase DBN model considering CCF revises the estimated safe operating time of the system from 566 h to 739 h. This effectively corrects the underestimation bias in reliability caused by the assumptions of full-cycle operation and independent failures, thereby providing a theoretical basis for optimizing maintenance strategies for EMU braking systems.

  • Open Access

    Research on Acoustic-Black-Hole-Type Baffles for Suspended Water Tanks of High-Speed Trains: Considering Vibration and Wave Suppression Characteristics

    by Sihui Dong, Yuebiao Zhao, Shiqun Li, Wenhao Bai, Xiang Shan

    To mitigate structural vibrations caused by liquid sloshing inside the suspended water tank of high-speed trains and to prevent issues such as baffle fatigue failure and water leakage from tank cracking, this study designed an acoustic black hole (ABH)-type baffle that comprehensively considers both vibration and wave suppression performance. Based on acoustic black hole (ABH) theory, numerical simulations were conducted using the CFD software Fluent to analyze the vibration and wave suppression characteristics of the ABH-type baffle under lateral and longitudinal impact conditions. The influence of the position and number of ABH structures on the baffle’s performance was systematically examined. Finally, the structural strength and the vibration/wave suppression capability of the baffle were validated. The results demonstrate that the structural strength of the ABH-type baffle meets the design requirements. Compared to a conventional baffle, the ABH-type baffle reduces the liquid sloshing force inside the tank, lowers the peak sloshing pressure under various operating conditions, and decreases the surface vibration velocity of the baffle within its dominant vibration frequency range of 0–100 Hz. The optimal positions of the ABH are located at the 80% and 20% water level lines of the baffle. The ABH-type baffle achieves the best suppression performance when the center of the ABH is horizontally aligned with the liquid surface. In addition, the vibration and wave suppression capability of the ABH-type baffle decreases when the number of ABHs is more or less than three.


  • Open Access

    Research on Acoustic Black Hole-Type Baffles for Suspended Water Tanks of High‑Speed Trains: Considering Vibration and Wave Suppression Characteristics

    by Sihui Dong, Yuebiao Zhao, Shiqun Li, Wenhao Bai, Xiang Shan

    To mitigate structural vibrations caused by liquid sloshing inside the suspended water tank of high-speed trains and to prevent issues such as baffle fatigue failure and water leakage from tank cracking, this study designed an acoustic black hole (ABH)-type baffle that comprehensively considers both vibration and wave suppression performance. Based on acoustic black hole (ABH) theory, numerical simulations were conducted using the CFD software Fluent to analyze the vibration and wave suppression characteristics of the ABH-type baffle under lateral and longitudinal impact conditions. The influence of the position and number of ABH structures on the baffle’s performance was systematically examined. Finally, the structural strength and the vibration/wave suppression capability of the baffle were validated.The results demonstrate that the structural strength of the ABH-type baffle meets the design requirements. Compared to a conventional baffle, the ABH-type baffle reduces the liquid sloshing force inside the tank, lowers the peak sloshing pressure under various operating conditions, and decreases the surface vibration velocity of the baffle within its dominant vibration frequency range of 0–100 Hz. The optimal positions for the ABHs are at the 80% and 20% water-level lines on the baffle, and the best suppression performance is achieved when the center of the ABH is aligned horizontally with the liquid surface. Furthermore, the vibration and wave suppression capability deteriorates when the number of ABHs is either greater or fewer than three.


  • Reliability Allocation Method for Complex Agricultural Machinery Systems Considering Demand‐Side Response and Insufficient Fault Data Correction

    by Shiqun Li, Qing Xia, Zhenliang Fu, Yonghua Li, Shaozuo Kuang

    Large‐scale agricultural machinery exhibits complex functionalities, limited test sample sizes, low fault data credibility, and urgent seasonal reliability demands, which challenge the precision of current reliability allocation methods. To better fulfill the reliability requirements of agricultural systems while accommodating industrial transformation and demand‐driven development trends in agricultural equipment, this study proposes a reliability allocation method tailored for complex agricultural machinery systems. Specifically, building upon structural–functional analysis and FMECA, an evaluation framework termed the 8B framework is established, comprising eight key indicators aligned with the characteristics of agricultural machinery. A multi‐factor maintainability definition method incorporating demand‐side response is proposed to quantify the feedback of user expectation deviations in reliability allocation. Using an improved TFN‐CRITIC‐IFM method for comprehensive weighting of the 8B framework, the weighting results are applied to the multi‐factor scoring matrix through slack factors, thereby establishing a failure rate allocation model for new products. Furthermore, a variable failure rate correction operator based on the parametric sigmoid function is introduced to characterize the dynamic approximation process of failure rate allocation results toward measured data, while avoiding excessive reliance on insufficient preliminary data with low credibility. A series system reliability allocation model considering demand‐side response and failure data correction is developed. The effectiveness of the proposed method is validated through a case study on a grain combine harvester.

  • Open Access

    Sensitivity Analysis and Optimization of Urban Roundabout Road Design Parameters Based on CFD

    by Hangyu Zhang, Sihui Dong, Shiqun Li, Shuai Zheng

    With the rapid advancement of urbanization, urban transportation systems are facing increasingly severe congestion challenges, especially at traditional roundabouts. The rapid increase in vehicles has led to a sharp increase in pressure at roundabouts. In order to alleviate the traffic pressure in the roundabout, this paper changes the road design parameters of the roundabout, uses a CFD method combined with sensitivity analysis to study the influence of different inlet angles, lane numbers, and the outer radius on the pressure, and seeks the road design parameter scheme with the optimal mitigation effect. Firstly, the full factorial experimental design method is used to select the sample points in the design sample space, and the response values of each sample matrix are obtained by CFD. Secondly, the response surface model between the road design parameters of the roundabout and the pressure in the ring is constructed. The single-factor analysis method and the multi-factor analysis method are used to analyze the influence of the road parameters on the pressure of each feature point, and then the moment-independent sensitivity analysis method based on the response surface model is used to solve the sensitivity distribution characteristics of the road design parameters of the roundabout. Finally, the Kriging surrogate model is constructed, and the NSGA-II is used to solve the multi-objective optimization problem to obtain the optimal solution set of road parameters. The results show that there are significant differences in the mechanism of action of different road geometric parameters on the pressure of each feature point of the roundabout, and it shows obvious spatial heterogeneity of parameter sensitivity. The pressure changes in the two feature points at the entrance conflict area and the inner ring weaving area are significantly correlated with the lane number parameters. There is a strong coupling relationship between the pressure of the maximum pressure extreme point in the ring and the radius parameters of the outer ring. According to the optimal scheme of road parameters, that is, when the parameter set (inlet angle/°, number of lanes, outer radius/m) meets (35.4, 5, 65), the pressures of the feature points decrease by 34.1%, 38.3%, and 20.7%, respectively, which has a significant effect on alleviating the pressure in the intersection. This study optimizes the geometric parameters of roundabouts through multidisciplinary methods, provides a data-driven congestion reduction strategy for the urban sustainable development framework, and significantly improves road traffic efficiency, which is crucial for building an efficient traffic network and promoting urban sustainable development.


  • Open Access

    Time-Varying Reliability Assessment of Urban Traffic Network Based on Dynamic Bayesian Network

    by Sihui Dong, Ni Jia, Shiqun Li, Yazhuo Zou

    With the advancement of urbanization and the proposal of sustainable development goals, the complexity and vulnerability of urban transportation systems have become increasingly prominent, and their reliability is directly related to the sustainable operation of urban transportation. The reliability of urban road networks, characterized by their dynamic nature, multi-scale characteristics, and anti-interference capabilities, directly restricts the functional guarantee of urban traffic and the efficiency of emergency response. To address the limitations of existing road network connectivity reliability assessment methods in representing time dynamics and modeling failure correlation, this study proposes a road network reliability assessment method based on a Dynamic Bayesian Network (DBN) by constructing a probabilistic reasoning model that integrates cascading failure characteristics. First, the connectivity reliability of the road network under random and targeted attack strategies was evaluated using a Monte Carlo simulation, revealing the impact of different attack strategies on network reliability. Subsequently, the congestion delay index is used as the standard of road section failure, considering the failure distribution and mutual dependence of road sections over time, a cascade failure mechanism is introduced, and a time-varying reliability assessment model based on a DBN is constructed. The effectiveness of the proposed method was verified through a case study of a partial road network in Dalian. The results show that ignoring cascading effects can significantly overestimate the reliability of the road network, especially during peak traffic hours, where such deviations may mask the real paralysis risks of the network. In contrast, the method proposed in this study fully considers time dynamics and failure correlation and can better capture the reliability of the road network under various dynamic conditions, providing a scientific basis for the sustainable planning and emergency management of urban traffic systems.


  • Open Access

    Sensitivity Analysis and Optimization of Urban Roundabout Road Design Parameters Based on CFD

    by Hangyu Zhang, Sihui Dong, Shiqun Li, Shuai Zheng

    With the rapid advancement of urbanization, urban transportation systems are facing increasingly severe congestion challenges, especially at traditional roundabouts. The rapid increase in vehicles has led to a sharp increase in pressure at roundabouts. In order to alleviate the traffic pressure in the roundabout, this paper changes the road design parameters of the roundabout, uses CFD method combined with sensitivity analysis to study the influence of different inlet angles, lane numbers and outer radius on the pressure, and seeks the road design parameter scheme with the optimal mitigation effect. Firstly, the full factorial experimental design method is used to select the sample points in the design sample space, and the response values of each sample matrix are obtained by CFD. Secondly, the response surface model between the road design parameters of the roundabout and the pressure in the ring is constructed. The single factor analysis method and the multi-factor analysis method are used to analyze the influence of the road parameters on the pressure of each feature point, and then the moment independent sensitivity analysis method based on the response surface model is used to solve the sensitivity distribution characteristics of the road design parameters of the roundabout. Finally, the Kriging surrogate model is constructed, and the NSGA-II is used to solve the multi-objective optimization problem to obtain the optimal solution set of road parameters. The results show that there are significant differences in the mechanism of action of different road geometric parameters on the pressure of each feature point of the roundabout, and it shows obvious spatial heterogeneity of parameter sensitivity. The pressure changes of the two feature points at the entrance conflict area and the inner ring weaving area are significantly correlated with the lane number parameters. There is a strong coupling relationship between the pressure of the maximum pressure extreme point in the ring and the radius parameters of the outer ring. According to the optimal scheme of road parameters, that is, when the parameter set (inlet angle/°, number of lanes, outer radius/ m) meets (35.4, 5, 65), the pressure of feature points decreases by 34.1%, 38.3% and 20.7% respectively, which has a significant effect on alleviating the pressure in the intersection. This study optimizes the geometric parameters of roundabouts through multidisciplinary methods, provides a data-driven congestion reduction strategy for the urban sustainable development framework, and significantly improves road traffic efficiency, which is crucial for building an efficient traffic network and promoting urban sustainable development.


  • Open Access

    Time-Varying Reliability Assessment of Urban Traffic Network Based on Dynamic Bayesian Network

    by Sihui Dong, Ni Jia, Shiqun Li, Yazhuo Zou

    With the advancement of urbanization, the complexity and fragility of urban traffic systems are becoming increasingly prominent. The reliability of urban road networks, characterized by their dynamic nature, multi-scale characteristics, and anti-interference capabilities, directly restricts the functional guarantee of urban traffic and the efficiency of emergency response. To address the limitations of existing road network connectivity reliability assessment methods in representing time dynamics and modeling failure correlation, this study proposes a road network reliability assessment method based on Dynamic Bayesian Network (DBN) by constructing a probabilistic reasoning model that integrates cascading failure characteristics. First, the connectivity reliability of the road network under random and targeted attack strategies was evaluated using Monte Carlo Simulation (MCS), revealing the impact of different attack strategies on network reliability. Subsequently, considering the time-dependent failure distribution of road sections and their interdependencies, a cascading failure mechanism was introduced to build a time-varying reliability assessment model based on DBN. The effectiveness of the proposed method was verified through a case study of a partial road network in Dalian. The results show that ignoring cascading effects can significantly overestimate the reliability of the road network, especially during peak traffic hours, where such deviations may mask the real paralysis risks of the network. In contrast, the method proposed in this study fully considers time dynamics and failure correlation, and can better capture the reliability of the road network under various dynamic conditions, providing a scientific basis for the resilience planning and emergency management of urban traffic systems.


  • A System Safety Assessment Method Considering Risk Correlation

    by Qing Xia, Yonghua Li, Shiqun Li, Zhiyang Zhang, Shujian Liu

    The safety of the system is affected by a variety of risk factors such as human, machine, environment, and management, and the risk factors interact with each other and are not independent. Describing the dynamic trends in the operational safety of a system with coupled risk factors is difficult. Therefore, a safety assessment method based on the IOWA‐IM‐FCM model is proposed. Combining the interval‐ordered weighted average (IOWA) operator to build an interaction matrix (IM) of risk factors. It can better express the fuzzy relationship between risk factors while weakening the influence of subjective factors and identifying key risk factors. Next, the IM elements are substituted into the fuzzy cognitive map (FCM) model to predict the system safety risk trends under the influence of risk factor interactions. Finally, the results of the analysis of the IM and the FCM model are integrated, and the system safety evaluation level is determined by the risk evaluation coefficient. The method was applied to a case study of a bogie system. Results indicate the bogie system operation risk is general, matching the real scenario. The method realizes quantitative prediction of the system risk trend under the coupling of risk factors with certain advantages.