Micael Frias Borges
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Micael Frias Borges has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Fernando Ventura Antunes
Centre for Mechanical Engineering, Materials and Processes (CEMMPRE), Department of Mechanical Engineering University of Coimbra Coimbra Portugal
8 shared publications - Pedro André Prates
Centre for Mechanical Technology and Automation (TEMA), Department of Mechanical Engineering, University of Aveiro, 3810-193 Aveiro, Portugal
8 shared publications - Ricardo Branco
University of Coimbra
6 shared publications F.V. Antunes
3 shared publications- Diogo Mariano Neto
University of Coimbra
2 shared publications A.S. Cruces
1 shared publication
Latest Publications
- Open Access
FCG Modelling Considering the Combined Effects of Cyclic Plastic Deformation and Growth of Micro-Voids
Fatigue is one of the most prevalent mechanisms of failure. Thus, the evaluation of the fatigue crack growth process is fundamental in engineering applications subjected to cyclic loads. The fatigue crack growth rate is usually accessed through the da/dN-ΔK curves, which have some well-known limitations. In this study a numerical model that uses the cyclic plastic strain at the crack tip to predict da/dN was coupled with the Gurson–Tvergaard–Needleman (GTN) damage model. The crack propagation process occurs, by node release, when the cumulative plastic strain reaches a critical value. The GTN model is used to account for the material degradation due to the growth of micro-voids process, which affects fatigue crack growth. Predictions with GTN are compared with the ones obtained without this ductile fracture model. Crack closure was studied in order to justify the lower values of da/dN obtained in the model with GTN, when compared with the results without GTN, for lower ΔK values. Finally, the accuracy of both variants of the numerical model is accessed through the comparison with experimental results.
Open AccessFCG Modelling Considering the Combined Effects of Cyclic Plastic Deformation and Growth of Micro-Voids
Fatigue is one of the most prevalent mechanisms of failure. Thus, the evaluation of the fatigue crack growth process is fundamental in engineering applications subjected to cyclic loads. The fatigue crack growth rate is usually accessed through the da/dN-ΔK curves, which have some well-known limitations. In this study a numerical model that uses the cyclic plastic strain at the crack tip to predict da/dN was coupled with the Gurson–Tvergaard–Needleman (GTN) damage model. The crack propagation process occurs, by node release, when the cumulative plastic strain reaches a critical value. The GTN model is used to account for the material degradation due to the growth of micro-voids process, which affects fatigue crack growth. Predictions with GTN are compared with the ones obtained without this ductile fracture model. Crack closure was studied in order to justify the lower values of da/dN obtained in the model with GTN, when compared with the results without GTN, for lower ΔK values. Finally, the accuracy of both variants of the numerical model is accessed through the comparison with experimental results.
- Open Access
Revisiting Classical Issues of Fatigue Crack Growth Using a Non-Linear Approach
Fatigue crack growth (FCG) has been studied for decades; however, several aspects are still objects of controversy. The objective here is to discuss different issues, using a numerical approach based on crack tip plastic strain, assuming that FCG is driven by crack tip deformation. ΔK was found to control cyclic plastic deformation at the crack tip, while Kmax has no effect. Therefore, alternative mechanisms are required to justify models based on ΔK and Kmax. The analysis of crack tip plastic deformation also showed that there is crack tip damage below crack closure. Therefore, the definition of an effective load range ΔKeff = Kmax − Kopen is not correct, because the portion of load range below opening also contributes to FCG. Below crack closure, damage occurs during unloading while during loading the crack tip deformation is elastic. However, if the maximum load is decreased below the elastic limit, which corresponds to the transition between elastic and elasto–plastic regimes, there is no crack tip damage. Additionally, a significant effect of the crack ligament on crack closure was found in tests with different crack lengths and the same ΔK. Finally, the analysis of FCG after an overload with and without contact of crack flanks showed that the typical variation of da/dN observed is linked to crack closure variations, while the residual stresses ahead of crack tip are not affected by the contact of crack flanks.
Open AccessRevisiting Classical Issues of Fatigue Crack Growth Using a Non-Linear Approach
Fatigue crack growth (FCG) has been studied for decades; however, several aspects are still objects of controversy. The objective here is to discuss different issues, using a numerical approach based on crack tip plastic strain, assuming that FCG is driven by crack tip deformation. ΔK was found to control cyclic plastic deformation at the crack tip, while Kmax has no effect. Therefore, alternative mechanisms are required to justify models based on ΔK and Kmax. The analysis of crack tip plastic deformation also showed that there is crack tip damage below crack closure. Therefore, the definition of an effective load range ΔKeff = Kmax − Kopen is not correct, because the portion of load range below opening also contributes to FCG. Below crack closure, damage occurs during unloading while during loading the crack tip deformation is elastic. However, if the maximum load is decreased below the elastic limit, which corresponds to the transition between elastic and elasto–plastic regimes, there is no crack tip damage. Additionally, a significant effect of the crack ligament on crack closure was found in tests with different crack lengths and the same ΔK. Finally, the analysis of FCG after an overload with and without contact of crack flanks showed that the typical variation of da/dN observed is linked to crack closure variations, while the residual stresses ahead of crack tip are not affected by the contact of crack flanks.
- 1 August 2020
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 108
Numerical simulation of fatigue crack growth based on accumulated plastic strain
- 1 August 2020
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 108
Numerical simulation of fatigue crack growth based on accumulated plastic strain
- Open Access
- 17 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (12) , 4174
Fatigue Crack Growth from Notches: A Numerical Analysis
A numerical approach based on plastic crack tip opening displacement (CTOD) was followed to study fatigue crack growth (FCG) from notches. The identification of fundamental mechanisms was made considering notched and unnotched models, with and without contact of crack flanks. Different parameters were studied, namely, notch radius, crack length, stress state, and material. The notch increases the plastic CTOD, and therefore fatigue crack growth rate, da/dN, as expected. The reduction of notch radius increases da/dN but reduces the notch affected zone. Ahead of the notch affected zone, da/dN increases linearly with crack growth, with a rate that increases linearly with the plastic CTOD. The crack closure phenomenon has a dramatic effect under plane stress conditions but a limited effect on plane strain conditions. In the former case, the contact of crack flanks reduces substantially the effect of notch radius and the size of the notch affected zone. These trends are associated with the increase of crack closure level with notch radius. The material does not affect the global trends, but the reduction of yield stress increases the level of plastic deformation and therefore da/dN. The effect of material, and also of stress state, is mainly associated with crack closure.
- 17 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (12) , 4174
Open AccessFatigue Crack Growth from Notches: A Numerical Analysis
A numerical approach based on plastic crack tip opening displacement (CTOD) was followed to study fatigue crack growth (FCG) from notches. The identification of fundamental mechanisms was made considering notched and unnotched models, with and without contact of crack flanks. Different parameters were studied, namely, notch radius, crack length, stress state, and material. The notch increases the plastic CTOD, and therefore fatigue crack growth rate, da/dN, as expected. The reduction of notch radius increases da/dN but reduces the notch affected zone. Ahead of the notch affected zone, da/dN increases linearly with crack growth, with a rate that increases linearly with the plastic CTOD. The crack closure phenomenon has a dramatic effect under plane stress conditions but a limited effect on plane strain conditions. In the former case, the contact of crack flanks reduces substantially the effect of notch radius and the size of the notch affected zone. These trends are associated with the increase of crack closure level with notch radius. The material does not affect the global trends, but the reduction of yield stress increases the level of plastic deformation and therefore da/dN. The effect of material, and also of stress state, is mainly associated with crack closure.
- 1 April 2020
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 106
Effect of kinematic hardening parameters on fatigue crack growth
- 1 April 2020
- Published by Elsevier in Theoretical and Applied Fracture Mechanics
- Vol. 106
Effect of kinematic hardening parameters on fatigue crack growth
- Open Access
Numerical Study on the Variability of Plastic CTOD
This paper presents a numerical study on the influence of material parameters and loading variability in the plastic crack tip opening displacement (CTOD) results. For this purpose, AA7050-T6 was selected as reference material and a middle-cracked tension specimen geometry was considered. The studied input parameters were the Young’s modulus, Poisson’s ratio, isotropic and kinematic hardening parameters and the maximum and minimum applied loads. The variability of the input parameters follows a Gaussian distribution. First, screening design-of-experiments were performed to identify the most influential parameters. Two types of screening designs were considered: one-factor-at-a-time and fractional factorial designs. Three analysis criteria were adopted, based on: main effect, index of influence and analysis of variance. Afterwards, metamodels were constructed to establish relationships between the most influential parameters and the plastic crack tip opening displacement (CTOD) range, based on two types of designs: Face-Centered Central Composite Design and Box-Behnken design. Finally, the metamodels were validated, enabling the expeditious evaluation of the variability in the plastic CTOD range; in addition, the variability in the fatigue crack growth rate was also evaluated.
Open AccessNumerical Study on the Variability of Plastic CTOD
This paper presents a numerical study on the influence of material parameters and loading variability in the plastic crack tip opening displacement (CTOD) results. For this purpose, AA7050-T6 was selected as reference material and a middle-cracked tension specimen geometry was considered. The studied input parameters were the Young’s modulus, Poisson’s ratio, isotropic and kinematic hardening parameters and the maximum and minimum applied loads. The variability of the input parameters follows a Gaussian distribution. First, screening design-of-experiments were performed to identify the most influential parameters. Two types of screening designs were considered: one-factor-at-a-time and fractional factorial designs. Three analysis criteria were adopted, based on: main effect, index of influence and analysis of variance. Afterwards, metamodels were constructed to establish relationships between the most influential parameters and the plastic crack tip opening displacement (CTOD) range, based on two types of designs: Face-Centered Central Composite Design and Box-Behnken design. Finally, the metamodels were validated, enabling the expeditious evaluation of the variability in the plastic CTOD range; in addition, the variability in the fatigue crack growth rate was also evaluated.
- 1 March 2020
- Published by Elsevier in International Journal of Fatigue
- Vol. 132
Effect of Young’s modulus on fatigue crack growth
- 1 March 2020
- Published by Elsevier in International Journal of Fatigue
- Vol. 132
Effect of Young’s modulus on fatigue crack growth
- Open Access
A Numerical Study of the Effect of Isotropic Hardening Parameters on Mode I Fatigue Crack Growth
The consideration of plastic crack tip opening displacement (CTOD, δp), as a crack driving force has given us the opportunity to predict fatigue crack growth (FCG) rate numerically, and, therefore, to develop parametric studies focused on the effect of loading, geometrical, and material parameters. The objective here is to study the effect of the isotropic hardening parameters of the Voce law on FCG, which are the isotropic saturation stress, YSat, and the isotropic saturation rate, CY. The increase of these hardening parameters causes δp to decrease. However, this effect is much more pronounced for YSat than CY. The variation is non-linear, and the rate of variation decreases with the increase of isotropic parameters. The increase of YSat increases the crack closure phenomenon. Finally, the influence of the isotropic parameters is more relevant for pure isotropic hardening than for mixed hardening.
Open AccessA Numerical Study of the Effect of Isotropic Hardening Parameters on Mode I Fatigue Crack Growth
The consideration of plastic crack tip opening displacement (CTOD, δp), as a crack driving force has given us the opportunity to predict fatigue crack growth (FCG) rate numerically, and, therefore, to develop parametric studies focused on the effect of loading, geometrical, and material parameters. The objective here is to study the effect of the isotropic hardening parameters of the Voce law on FCG, which are the isotropic saturation stress, YSat, and the isotropic saturation rate, CY. The increase of these hardening parameters causes δp to decrease. However, this effect is much more pronounced for YSat than CY. The variation is non-linear, and the rate of variation decreases with the increase of isotropic parameters. The increase of YSat increases the crack closure phenomenon. Finally, the influence of the isotropic parameters is more relevant for pure isotropic hardening than for mixed hardening.
- Open Access
- 1 January 2020
- Published by Elsevier in Procedia Structural Integrity
- Vol. 25, 254-261
Model for fatigue crack growth analysis
- 1 January 2020
- Published by Elsevier in Procedia Structural Integrity
- Vol. 25, 254-261
Open AccessModel for fatigue crack growth analysis
- Open Access
- 11 July 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (50) , 9-19
Effect of yield stress on fatigue crack growth
Fatigue crack growth (FCG) depends on loading, geometry and also material properties. Since FCG is supposedly linked to crack tip plastic deformation, material’s yield stress, Y0, is an important parameter. The main objective here is to develop a parametric study focused on the effect of Y0 on FCG. The study is based on the plastic CTOD, dp, determined numerically using the finite element method. The increase of Y0 was found to decrease dp, and therefore FCG rate. The variation is non-linear, being more important for lower values of Y0. The effect of Y0 was found to be much more relevant for the 7050 aluminium alloy than for the 304L stainless steel, which indicated a major influence of isotropic saturation stress. With the inclusion of crack closure, the reduction of dp is kept, but there is a substantial reduction of dp and therefore of FCG rate.
- 11 July 2019
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 13 (50) , 9-19
Open AccessEffect of yield stress on fatigue crack growth
Fatigue crack growth (FCG) depends on loading, geometry and also material properties. Since FCG is supposedly linked to crack tip plastic deformation, material’s yield stress, Y0, is an important parameter. The main objective here is to develop a parametric study focused on the effect of Y0 on FCG. The study is based on the plastic CTOD, dp, determined numerically using the finite element method. The increase of Y0 was found to decrease dp, and therefore FCG rate. The variation is non-linear, being more important for lower values of Y0. The effect of Y0 was found to be much more relevant for the 7050 aluminium alloy than for the 304L stainless steel, which indicated a major influence of isotropic saturation stress. With the inclusion of crack closure, the reduction of dp is kept, but there is a substantial reduction of dp and therefore of FCG rate.