Syafawati Hasbi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Syafawati Hasbi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Mohd Shahneel Saharudin
School of Computing and Engineering Technology, Robert Gordon University, Garthdee Road, Aberdeen AB10 7QB, UK
3 shared publications - Emy Zairah Ahmad
Fakulti Teknologi Kejuruteraan Elektrikal dan Elektronik, Kampus Teknologi, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100, Durian Tunggal, Melaka, Malaysia
1 shared publication - Fawad Inam
School of Architecture, Computing and Engineering, University of East London, London, UK
1 shared publication - Fawad Inam
School of Architecture, Computing and Engineering, University of East London, London, United Kingdom
1 shared publication - Islam Shyha
School of Computing, Engineering and the Built Environment, Edinburgh Napier University, Edinburgh EH10 5DT, UK
1 shared publication Kin Yuen Leong
Department of Mechanical Engineering, Faculty of Engineering, Universiti Pertahanan Nasional Malaysia, Kem Sungai Besi, 57000 Kuala Lumpur
1 shared publication
Latest Publications
- Open Access
- 30 November 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 26 (1) , 54-65
Comparative Analysis of Mechanical Response in Epoxy Nanocomposites Reinforced with MXene and Other Carbon-Based Nano-Fillers: An Experimental and Numerical Study
This research introduces a finite element model tailored explicitly to assess the mechanical characteristics inherent in MXene/polymer nanocomposite. The primary focus revolves around elucidating the performance attributes through numerical simulations and subsequently aligning these findings with experimental data. The numerical analysis not only predicts mechanical behaviours but also aims to correlate these insights with experimental results obtained from fabricated epoxy nanocomposites within the study's scope. By employing this simulation-driven approach, the study investigates a deeper understanding of the mechanical response, particularly focusing on the materials' tensile properties. From the experimental results, the MXene/epoxy nanocomposite sample exhibited the highest tensile strength and modulus, measuring 50.1 MPa and 7.13 GPa, respectively. The simulation results were 50.08 MPa and 6.95 GPa, showing a difference of less than 3%. Small discrepancies in Young's modulus between the experimental and simulation results may arise from inherent sample heterogeneity. This heterogeneity, which includes microstructural variations, impurities, or defects, contrasts with the idealized homogeneous structures assumed in simulations. This research endeavours to advance predictive modelling techniques, offering valuable insights that can potentially streamline the manufacturing process and optimize MXene-based polymer composites. The goal is to tailor these materials with precise mechanical properties, ensuring their enhanced performance in various applications.
- 30 November 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 26 (1) , 54-65
Open AccessComparative Analysis of Mechanical Response in Epoxy Nanocomposites Reinforced with MXene and Other Carbon-Based Nano-Fillers: An Experimental and Numerical Study
This research introduces a finite element model tailored explicitly to assess the mechanical characteristics inherent in MXene/polymer nanocomposite. The primary focus revolves around elucidating the performance attributes through numerical simulations and subsequently aligning these findings with experimental data. The numerical analysis not only predicts mechanical behaviours but also aims to correlate these insights with experimental results obtained from fabricated epoxy nanocomposites within the study's scope. By employing this simulation-driven approach, the study investigates a deeper understanding of the mechanical response, particularly focusing on the materials' tensile properties. From the experimental results, the MXene/epoxy nanocomposite sample exhibited the highest tensile strength and modulus, measuring 50.1 MPa and 7.13 GPa, respectively. The simulation results were 50.08 MPa and 6.95 GPa, showing a difference of less than 3%. Small discrepancies in Young's modulus between the experimental and simulation results may arise from inherent sample heterogeneity. This heterogeneity, which includes microstructural variations, impurities, or defects, contrasts with the idealized homogeneous structures assumed in simulations. This research endeavours to advance predictive modelling techniques, offering valuable insights that can potentially streamline the manufacturing process and optimize MXene-based polymer composites. The goal is to tailor these materials with precise mechanical properties, ensuring their enhanced performance in various applications.
- Open Access
- 30 March 2023
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 20 (1) , 10247-10257
Development of Coconut Oil/Capric Acid Eutectic Phase Change Material with Graphene as Latent Thermal Energy Storage
In this study, a eutectic mixture of coconut oil (CO)-capric acid (CA) was synthesised and investigated with the aim of producing newly eutectic phase change materials (PCMs) with improved thermal properties as thermal energy storage (TES). Although eutectic fatty acids have been widely studied, the information on the thermal properties of the CO-CA eutectic mixture is very limited to the authors’ knowledge. Coconut oil offers good thermal and chemical stability with acceptable latent heat and melting temperature. The thermal properties of the eutectic mixture were enhanced by graphene addition at 1, 3, 5, and 7 wt% concentrations. The surfactant was added to the mixture to avoid the sedimentation of graphene. The material characterisation techniques include thermal conductivity measurement, Fourier Transform Infrared (FTIR) spectroscopy, Differential Scanning Calorimetry (DSC), and Thermal Gravimetric (TG) analysis. The results revealed that the pure eutectic CO-CA has a melting point of 23.5°C with a latent heat of 110 J/g. With the addition of graphene, the melting point of the mixture is 22.8°C, and the latent heat is 103 J/g. Overall, the findings showed that the thermal conductivity improved by 21.7% for 7wt% graphene concentration. The spectra from FTIR and TG analysis showed that the mixture offers thermal and chemical stability. The promising findings in this study showed that the newly developed eutectic mixture with improved thermal properties makes them favourable to be used as TES for low-temperature applications.
- 30 March 2023
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 20 (1) , 10247-10257
Open AccessDevelopment of Coconut Oil/Capric Acid Eutectic Phase Change Material with Graphene as Latent Thermal Energy Storage
In this study, a eutectic mixture of coconut oil (CO)-capric acid (CA) was synthesised and investigated with the aim of producing newly eutectic phase change materials (PCMs) with improved thermal properties as thermal energy storage (TES). Although eutectic fatty acids have been widely studied, the information on the thermal properties of the CO-CA eutectic mixture is very limited to the authors’ knowledge. Coconut oil offers good thermal and chemical stability with acceptable latent heat and melting temperature. The thermal properties of the eutectic mixture were enhanced by graphene addition at 1, 3, 5, and 7 wt% concentrations. The surfactant was added to the mixture to avoid the sedimentation of graphene. The material characterisation techniques include thermal conductivity measurement, Fourier Transform Infrared (FTIR) spectroscopy, Differential Scanning Calorimetry (DSC), and Thermal Gravimetric (TG) analysis. The results revealed that the pure eutectic CO-CA has a melting point of 23.5°C with a latent heat of 110 J/g. With the addition of graphene, the melting point of the mixture is 22.8°C, and the latent heat is 103 J/g. Overall, the findings showed that the thermal conductivity improved by 21.7% for 7wt% graphene concentration. The spectra from FTIR and TG analysis showed that the mixture offers thermal and chemical stability. The promising findings in this study showed that the newly developed eutectic mixture with improved thermal properties makes them favourable to be used as TES for low-temperature applications.
- Open Access
- 14 March 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (6) , 5125
Advances in Sustainable Nanocomposites
Advances in Sustainable Nanocomposites is a newly opened Special Issue of Sustainability, that aims to publish original and review papers on the new scientific development of sustainable nanocomposite materials that are accelerated by zero-carbon policy goals
- 14 March 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (6) , 5125
Open AccessAdvances in Sustainable Nanocomposites
Advances in Sustainable Nanocomposites is a newly opened Special Issue of Sustainability, that aims to publish original and review papers on the new scientific development of sustainable nanocomposite materials that are accelerated by zero-carbon policy goals