Eduardo Camacho- Espinosa
Research Subjects
Eduardo Camacho- Espinosa has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Ricardo Mis-Fernández
Applied Physics Department, CINVESTAV-IPN, Mérida, C.P. 97310, Yucatán, México
7 shared publications - Eduardo Flores
Applied Physics Department, Center for Research and Advanced Studies (CINVESTAV-Merida), Merida 97310, Mexico
5 shared publications - Enrique Rosendo
Posgrado en Dispositivos Semiconductores (PDS), Benemérita Universidad Autónoma de Puebla (BUAP)
4 shared publications - Mariely Loeza-Poot
Centro de Investigación y de Estudios Avanzados del IPN-Unidad Mérida
4 shared publications - Ana Cristina Carranza Sanchez
Posgrado en Dispositivos Semiconductores (PDS), Benemérita Universidad Autónoma de Puebla (BUAP), Puebla, México
3 shared publications - Crisoforo Morales
Centro de Investigaciónes en semiconductores, Instituto de Ciencias (ICUAP). BUAP
2 shared publications
Latest Publications
- Open Access
- 24 July 2026
- Published by Elsevier in Solar Energy
- Vol. 316
Indium-dependent performance and voltage limitation in fully sputtered indium zinc oxide/CdTe solar cells
- 24 July 2026
- Published by Elsevier in Solar Energy
- Vol. 316
Open AccessIndium-dependent performance and voltage limitation in fully sputtered indium zinc oxide/CdTe solar cells
- Open Access
- 12 May 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 343
Strategic TCO selection: Insights from MTO/TCO bilayer coupling analysis
- 12 May 2025
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 343
Open AccessStrategic TCO selection: Insights from MTO/TCO bilayer coupling analysis
- Open Access
- 29 November 2024
- Published by Universidad Autonoma del Estado de Hidalgo in Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI
- Vol. 12, 103-110
Calidad de Cu3N según la temperatura de depósito
El nitruro de cobre (Cu3N) es un material prometedor en aplicaciones como la microelectrónica y energías renovables, donde su optimización depende de entender cómo las condiciones de depósito afectan sus propiedades. En este estudio se utilizó la técnica de erosión catódica reactiva para depositar películas delgadas de Cu3N a temperaturas desde ambiente hasta 300 °C y se analizaron sus propiedades estructurales, ópticas y eléctricas mediante las técnicas de XRD, espectrofotometría VIS-NIR y efecto Hall, respectivamente. Se observó que la resistividad disminuye y la movilidad de portadores aumenta con la temperatura, alcanzando valores característicos de los metales a 300 °C. A esta temperatura, se evidencia una descomposición parcial del Cu3N en cobre metálico, lo que se refleja en una baja transmitancia y picos que identifican al Cu en difracción de rayos x. Estos resultados sugieren que ajustar la temperatura de depósito puede modificar las propiedades optoelectrónicas de las películas de Cu3N, lo que es relevante para el desarrollo de dispositivos semiconductores.
- 29 November 2024
- Published by Universidad Autonoma del Estado de Hidalgo in Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI
- Vol. 12, 103-110
Open AccessCalidad de Cu3N según la temperatura de depósito
El nitruro de cobre (Cu3N) es un material prometedor en aplicaciones como la microelectrónica y energías renovables, donde su optimización depende de entender cómo las condiciones de depósito afectan sus propiedades. En este estudio se utilizó la técnica de erosión catódica reactiva para depositar películas delgadas de Cu3N a temperaturas desde ambiente hasta 300 °C y se analizaron sus propiedades estructurales, ópticas y eléctricas mediante las técnicas de XRD, espectrofotometría VIS-NIR y efecto Hall, respectivamente. Se observó que la resistividad disminuye y la movilidad de portadores aumenta con la temperatura, alcanzando valores característicos de los metales a 300 °C. A esta temperatura, se evidencia una descomposición parcial del Cu3N en cobre metálico, lo que se refleja en una baja transmitancia y picos que identifican al Cu en difracción de rayos x. Estos resultados sugieren que ajustar la temperatura de depósito puede modificar las propiedades optoelectrónicas de las películas de Cu3N, lo que es relevante para el desarrollo de dispositivos semiconductores.
- Open Access
- 29 November 2024
- Published by Universidad Autonoma del Estado de Hidalgo in Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI
- Vol. 12, 88-95
Metalización por Sputtering usando un horno porta-sustrato ad-hoc
En este trabajo se presenta el diseño, fabricación, y puesta a punto de un horno porta-sustrato utilizado para depositar películas delgadas metálicas por la técnica de Sputtering. El sistema debe ser capaz de soportar condiciones de alto vacío y alta temperatura, así como adecuarse dentro de una cámara de vacío en forma cilíndrica, teniendo como principal reto la distribución de los componentes al tratarse de un sistema compacto y de bajo costo. El horno porta-sustrato fue diseñado de forma octagonal mediante software CAD, usando para su fabricación acero inoxidable, cerámica, grafito, lámparas de cuarzo, entre otros. Para la caracterización del horno, se realizaron curvas de calentamiento ajustando la potencia de las lámparas. Con el fin de evaluar la funcionalidad del sistema, se depositaron y caracterizaron películas delgadas de Ag en sustratos de vidrio; así mismo, se realizó la metalización con Ag de los contactos posteriores de una celda solar de película delgada basada en CdTe.
- 29 November 2024
- Published by Universidad Autonoma del Estado de Hidalgo in Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI
- Vol. 12, 88-95
Open AccessMetalización por Sputtering usando un horno porta-sustrato ad-hoc
En este trabajo se presenta el diseño, fabricación, y puesta a punto de un horno porta-sustrato utilizado para depositar películas delgadas metálicas por la técnica de Sputtering. El sistema debe ser capaz de soportar condiciones de alto vacío y alta temperatura, así como adecuarse dentro de una cámara de vacío en forma cilíndrica, teniendo como principal reto la distribución de los componentes al tratarse de un sistema compacto y de bajo costo. El horno porta-sustrato fue diseñado de forma octagonal mediante software CAD, usando para su fabricación acero inoxidable, cerámica, grafito, lámparas de cuarzo, entre otros. Para la caracterización del horno, se realizaron curvas de calentamiento ajustando la potencia de las lámparas. Con el fin de evaluar la funcionalidad del sistema, se depositaron y caracterizaron películas delgadas de Ag en sustratos de vidrio; así mismo, se realizó la metalización con Ag de los contactos posteriores de una celda solar de película delgada basada en CdTe.
- 18 April 2024
- Published by Elsevier in Solar Energy
- Vol. 273
Mg-doped SnO2 properties modulation applied to all-sputtered CdTe solar cells
- 18 April 2024
- Published by Elsevier in Solar Energy
- Vol. 273
Mg-doped SnO2 properties modulation applied to all-sputtered CdTe solar cells
- 17 April 2024
- Published by Elsevier in Applied Surface Science
- Vol. 662
Physico-chemical analysis of the properties and stability of CdS and CdS:O to be applied in thin-film solar cells
- 17 April 2024
- Published by Elsevier in Applied Surface Science
- Vol. 662
Physico-chemical analysis of the properties and stability of CdS and CdS:O to be applied in thin-film solar cells
- Open Access
Influence of Sulfurization Time on Sb2S3 Synthesis Using a New Graphite Box Design
In recent years, antimony sulfide (Sb2S3) has been investigated as a photovoltaic absorber material due to its suitable absorber coefficient, direct band gap, extinction coefficient, earth-abundant, and environmentally friendly constituents. Therefore, this work proposes Sb2S3 film preparation by an effective two-step process using a new graphite box design and sulfur distribution, which has a high repeatability level and can be scalable. First, an Sb thin film was deposited using the RF-Sputtering technique, and after that, the samples were annealed with elemental sulfur into a graphite box, varying the sulfurization time from 20 to 50 min. The structural, optical, morphological, and chemical characteristics of the resulting thin films were analyzed. Results reveal the method’s effectivity and the best properties were obtained for the sample sulfurized during 40 min. This Sb2S3 thin film presents an orthorhombic crystalline structure, elongated grains, a band gap of 1.69 eV, a crystallite size of 15.25 Å, and a nearly stoichiometric composition. In addition, the formation of a p-n junction was achieved by depositing silver back contact on the Glass/FTO/CdS/Sb2S3 structure. Therefore, the graphite box design has been demonstrated to be functional to obtain Sb2S3 by a two-step process.
Open AccessInfluence of Sulfurization Time on Sb2S3 Synthesis Using a New Graphite Box Design
In recent years, antimony sulfide (Sb2S3) has been investigated as a photovoltaic absorber material due to its suitable absorber coefficient, direct band gap, extinction coefficient, earth-abundant, and environmentally friendly constituents. Therefore, this work proposes Sb2S3 film preparation by an effective two-step process using a new graphite box design and sulfur distribution, which has a high repeatability level and can be scalable. First, an Sb thin film was deposited using the RF-Sputtering technique, and after that, the samples were annealed with elemental sulfur into a graphite box, varying the sulfurization time from 20 to 50 min. The structural, optical, morphological, and chemical characteristics of the resulting thin films were analyzed. Results reveal the method’s effectivity and the best properties were obtained for the sample sulfurized during 40 min. This Sb2S3 thin film presents an orthorhombic crystalline structure, elongated grains, a band gap of 1.69 eV, a crystallite size of 15.25 Å, and a nearly stoichiometric composition. In addition, the formation of a p-n junction was achieved by depositing silver back contact on the Glass/FTO/CdS/Sb2S3 structure. Therefore, the graphite box design has been demonstrated to be functional to obtain Sb2S3 by a two-step process.
- Open Access
Numerical Simulation and Performance Optimization of a Solar Cell Based on WO3/CdTe Heterostructure Using NiO as HTL Layer by SCAPS 1D
In this paper, a solar cell based on /CdTe heterojunction was analyzed and optimized, for which the following structure of the Al/AZO//CdTe/NiO/Ni device was proposed, which was numerically simulated by the SCAPS 1-D software. Using the software, the effect of the thickness and carrier concentration of the absorber layer (CdTe) and the window layer () was analyzed, and the optimal value of these parameters was found to be 2 µm and for the CdTe layer and 10 nm and for the layer, respectively. The influence of the defect density of the /CdTe interface on the performance of the proposed cell was also analyzed, simulating from to , obtaining better device performance at lower interface defect density. Another parameter analyzed was the operating temperature on the photovoltaic performance of the device, observing that the solar cell has a better performance at lower temperatures. Finally, a maximum optimized PCE of 19.87% is obtained with a Voc = 0.85 V, Jsc = 28.45 , and FF = 82.03%, which makes the /CdTe heterojunction an interesting alternative for the development of CdTe-based solar cells.Open AccessNumerical Simulation and Performance Optimization of a Solar Cell Based on WO3/CdTe Heterostructure Using NiO as HTL Layer by SCAPS 1D
In this paper, a solar cell based on /CdTe heterojunction was analyzed and optimized, for which the following structure of the Al/AZO//CdTe/NiO/Ni device was proposed, which was numerically simulated by the SCAPS 1-D software. Using the software, the effect of the thickness and carrier concentration of the absorber layer (CdTe) and the window layer () was analyzed, and the optimal value of these parameters was found to be 2 µm and for the CdTe layer and 10 nm and for the layer, respectively. The influence of the defect density of the /CdTe interface on the performance of the proposed cell was also analyzed, simulating from to , obtaining better device performance at lower interface defect density. Another parameter analyzed was the operating temperature on the photovoltaic performance of the device, observing that the solar cell has a better performance at lower temperatures. Finally, a maximum optimized PCE of 19.87% is obtained with a Voc = 0.85 V, Jsc = 28.45 , and FF = 82.03%, which makes the /CdTe heterojunction an interesting alternative for the development of CdTe-based solar cells.