Tala Hemmati Shahsavar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tala Hemmati Shahsavar has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Dmitri Vinnikov
Department of Electrical Power Engineering and Mechatronics, Tallinn University of Technology, Tallinn, Estonia
3 shared publications - Oleksandr Husev
Department of Industrial Electronics, Warsaw University of Technology, Warsaw, Poland
3 shared publications - Naser Vosoughi Kurdkandi
Department of Electrical and Computer Engineering, San Diego State University, San Diego, CA 92182, USA
2 shared publications - Oleksandr Matiushkin
Tallinn University of Technology, Tallinn, Estonia
2 shared publications - Arash Khoshkbar-Sadigh
School of Electrical Engineering and Computer Science, Pennsylvania State University, University Park, PA, USA
1 shared publication - Artem Fesenko
Department of Radiotechnic and Embeded Systems, Chernihiv Polytechnic National University, 14027 Chernihiv, Ukraine
1 shared publication
Latest Publications
- 1 April 2026
- Published by Springer Nature
- p. 142-158
Performance Benchmarking Platform for Building Energy Management Systems
- 1 April 2026
- Published by Springer Nature
- p. 142-158
Performance Benchmarking Platform for Building Energy Management Systems
- 26 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15755-15767
A High Step-Up Non-Isolated DC-DC Converter With Low Voltage Stress Across Transistor
Based on the coupled inductor and voltage multiplier cells (VMCs), a nonisolated ultrahigh step-up dc–dc converter topology is presented in this article. The secondary side of the coupled inductor is paired with VMC in order to raise the output voltage. Therefore, a higher voltage gain with lower duty cycles is achieved by combining the coupled inductor and VMC approach, thus enhancing the overall robustness of the system. In addition, VMCs suppress the peak voltages across the power switches that leads to mitigate the maximum voltage throughout the switches intensively. Continuous input current with lower ripple and ultrahigh voltage gain with very low voltage stress over the semiconductors are the main benefits of the suggested topology. A comprehensive discussion of the proposed converter's operational modes, steady-state performance, design process, and a comparison with other similar converters have been provided in this literature. Moreover, to illustrate the converter’s performance, an experimental prototype with a 240 W rating power, input voltage range of 14–60 V, and output voltage of 350 V at a switching frequency of 60 kHz was constructed, and the outcomes of the experiment are showcased.
- 26 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (12) , 15755-15767
A High Step-Up Non-Isolated DC-DC Converter With Low Voltage Stress Across Transistor
Based on the coupled inductor and voltage multiplier cells (VMCs), a nonisolated ultrahigh step-up dc–dc converter topology is presented in this article. The secondary side of the coupled inductor is paired with VMC in order to raise the output voltage. Therefore, a higher voltage gain with lower duty cycles is achieved by combining the coupled inductor and VMC approach, thus enhancing the overall robustness of the system. In addition, VMCs suppress the peak voltages across the power switches that leads to mitigate the maximum voltage throughout the switches intensively. Continuous input current with lower ripple and ultrahigh voltage gain with very low voltage stress over the semiconductors are the main benefits of the suggested topology. A comprehensive discussion of the proposed converter's operational modes, steady-state performance, design process, and a comparison with other similar converters have been provided in this literature. Moreover, to illustrate the converter’s performance, an experimental prototype with a 240 W rating power, input voltage range of 14–60 V, and output voltage of 350 V at a switching frequency of 60 kHz was constructed, and the outcomes of the experiment are showcased.
- Open Access
Comparative Evaluation of Common-Ground Converters for Dual-Purpose Application
The focus of this paper is to provide a comparative analysis of various common-ground converters that serve as dual-purpose power electronic interfaces. These interfaces are designed to be used in both DC and single-phase AC grids, utilizing the same terminals for both modes of operation. The idea lies in the utilization of the same semiconductors in the DC-DC and DC-AC configurations, resulting in minimal redundancy. Particular attention is focused on the comparative evaluation approach. A novel Flying Inductor (FI)-based converter was selected for experimental verification. The design example and experimental prototype of a dual-purpose DC-DC/AC power electronic converter is capable of providing 2 kVA of power in AC mode and 4 kW in DC mode. The experimental results indicate that the converter can operate in both AC and DC grids according to their respective modes. The conclusion of the study highlights the potential applications and main benefits of this technology.
Open AccessComparative Evaluation of Common-Ground Converters for Dual-Purpose Application
The focus of this paper is to provide a comparative analysis of various common-ground converters that serve as dual-purpose power electronic interfaces. These interfaces are designed to be used in both DC and single-phase AC grids, utilizing the same terminals for both modes of operation. The idea lies in the utilization of the same semiconductors in the DC-DC and DC-AC configurations, resulting in minimal redundancy. Particular attention is focused on the comparative evaluation approach. A novel Flying Inductor (FI)-based converter was selected for experimental verification. The design example and experimental prototype of a dual-purpose DC-DC/AC power electronic converter is capable of providing 2 kVA of power in AC mode and 4 kW in DC mode. The experimental results indicate that the converter can operate in both AC and DC grids according to their respective modes. The conclusion of the study highlights the potential applications and main benefits of this technology.
- 19 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (2) , 447-459
A New Flying Capacitor-Based Buck–Boost Converter for Dual-Purpose Applications
A novel dual-purpose common ground dc-dc/ac power converter is proposed in this paper. It is based on the flying capacitor circuit along with boost circuit, which in turns provides a wide range of the input voltage regulation with the capability of stepping up or down the output voltage. The same components are used under both dc-dc and dc-ac modes which reduces the redundancy of the used devices. Particular attention is dedicated to the working modes of the proposed solution. The special control system is implemented to provide acceptable current and voltage quality in off-grid and grid-connected modes. To underline the pros and cons of the proposed solution, the comprehensive comparison is performed. Finally, the performance of the proposed dual-purpose power converter is investigated through an experimental 3.5 kw / 5 kw setup, for dc-ac and dc-dc operating modes, respectively. Main oscillograms along with efficiency analysis are presented and discussed in conclusions.
- 19 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (2) , 447-459
A New Flying Capacitor-Based Buck–Boost Converter for Dual-Purpose Applications
A novel dual-purpose common ground dc-dc/ac power converter is proposed in this paper. It is based on the flying capacitor circuit along with boost circuit, which in turns provides a wide range of the input voltage regulation with the capability of stepping up or down the output voltage. The same components are used under both dc-dc and dc-ac modes which reduces the redundancy of the used devices. Particular attention is dedicated to the working modes of the proposed solution. The special control system is implemented to provide acceptable current and voltage quality in off-grid and grid-connected modes. To underline the pros and cons of the proposed solution, the comprehensive comparison is performed. Finally, the performance of the proposed dual-purpose power converter is investigated through an experimental 3.5 kw / 5 kw setup, for dc-ac and dc-dc operating modes, respectively. Main oscillograms along with efficiency analysis are presented and discussed in conclusions.