YYYavuz Yenginar

Yavuz Yenginar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yavuz Yenginar has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The role of foundation and soil stiffness in the analysis of circular raft foundations in cohesionless soils

    by Ali Serdar Ecemiş, Yavuz Yenginar, İlYas Özkan

    The design of raft foundations requires an accurate prediction of their load-settlement behavior, which is governed by the relative stiffness of the raft and the soil. The raft-soil stiffness coefficient (Krs) is used to classify this behavior, but the existing range for partially rigid foundations (0.001<Krs<1000) is excessively broad and offers limited practical guidance for engineers. This study aims to refine this classification for uniformly loaded circular raft foundations on cohesionless soils by introducing the differential settlement ratio (DSR) as a quantitative criterion, and to determine the most appropriate analysis method for each behavioral class. A comprehensive finite element analysis was conducted on 7 circular raft foundation models. The models incorporated varying concrete classes (C20-C40), thicknesses (0.3-2.7m), diameters (4.8-48m), and were situated on loose, medium dense, and dense sands. Each foundation was analyzed using both the Winkler method and the Pseudo-Coupled (PC) method, and the resulting settlement profiles were evaluated based on DSR. The results demonstrate that foundations with Krs≤1 exhibit DSR values of approximately 50%, indicating fully flexible behavior, and the PC method is required for a realistic settlement analysis. Foundations with Krs≥10 exhibit negligible DSR (10-12%), behaving as fully rigid, and the Winkler method is sufficient. The critical finding is that foundations within the narrowed range of 1<Krs<10 are identified as partially rigid, where DSR decreases progressively with increasing Krs. In this zone, the PC method provides safer and more accurate results than the Winkler method. This study provides engineers with a practical, DSR-based refined classification (flexible: Krs≤1; partially rigid: 1<Krs<10; rigid: Krs≥10) and clear recommendations for selecting the appropriate analysis method, thereby enhancing the accuracy and safety of raft foundation design.

  • Open Access

    Reducing pavement cost using biochar derived from Agaricus bisporus compost waste

    by Saadoon Obaid Eyada, Silda Ghazi Mohammed Doori, Yavuz Yenginar

  • Ankastre Temel, Winkler ve Psödo-eşlenik Yöntemlerine Göre Üstyapı Performansının İncelenmesi

    by Ali Serdar Ecemiş, Yavuz Yenginar, İlYas Özkan

    Bu çalışmada, orta sıkı kumlu zemin üzerine oturan 5 katlı bir binanın performansı ankastre temel, Winkler ve Pseudo-eşlenik yöntemleriyle analiz edilmiştir. Yapının periyodu, kolonlara etki eden eksenel yükler ve kesme kuvvetleri, deprem kuvvetleri, kat yer değiştirmeleri, temel taban basıncı ve yer değiştirme değerleri statik ve dinamik yükleme durumlarında belirlenmiştir. Yapısal mühendislikte kullanılan temel çözüm yöntemi, çeşitli yükleme koşullarında binaların dinamik ve statik davranışlarını derinden etkilemektedir. Winkler ve Pseudo-eşlenik yöntemlerinin ankastre temele göre karşılaştırılmasıyla, birkaç önemli fark ortaya çıkmıştır: Winkler ve Pseudo-eşlenik yöntemlerinde bina periyotları birbirine yakın iken ankastre temel çözümünde periyot %6,7 daha fazla olmaktadır. Ölü ve hareketli yük (G+Q) altında kolonlara etki eden eksenel yükler temel analiz yönteminden oldukça az etkilenmektedir, ancak deprem (EQx) yükü altında Winkler ve Pseudo-eşlenik yöntemleri, ankastre temel yöntemine göre 1. ve 5. kat kolonlarındaki eksenel yükleri önemli ölçüde azalmaktadır. Köşe kolonlarındaki kesme kuvvetleri Winkler ve Pseudo-eşlenik yöntemlerinde %46 daha düşük elde edilmiştir. Ayrıca, bu yöntemler deprem kuvvetinde %7 artış ve ankastre temel yöntemine göre %4,7 daha az kat yer değiştirmesi sonucunu vermiştir. Maksimum temel basıncı, oturma ve farklı oturmanın konumu, kullanılan temel analiz yöntemine bağlı olarak değişmektedir. Bu bulgular, özellikle deprem olayları gibi farklı yükleme senaryoları altında yapısal stabilite, performans ve dayanıklılığın optimize edilmesinde temel seçiminin kritik rolünü vurgulamaktadır.

  • Open Access

    Düşey ve Deprem Yükleri Altında Tünel Kalıp Sistemli Bir Binanın Farklı Temel-Zemin Modellerine Göre Analizi

    by Ali Serdar Ecemiş, Yavuz Yenginar, İlYas Özkan

    Bu çalışmada 8 katlı tünel kalıp taşıyıcı sisteme sahip bina sonlu elemanlar metodu ile analiz edilmiştir. Yapı-temel sistemi için üç farklı zemin profili (ZC, ZD, ZE), üç farklı yükleme koşulu (1.4G+1.6Q; G+Q+EX, G+Q+EY) ve iki farklı temel modellemesi (ankastre çözüm, Winkler metodu) dikkate alınmıştır. Analiz sonucuna deprem kuvvetleri, tasarım ivme değerleri, periyodlar, zemin gerilmeleri, temeldeki oturmalar, kat deplasmanları ve perde tasarım kuvvetlerindeki değişim karşılaştırılmıştır. ZC’den ZE zemin sınıfına doğru gidildikçe TA ve TB arasındaki fark büyüdüğü için, ZE sınıfı zemin üzerine yapılacak yapıların maksimum ivmeye maruz kalma ihtimali diğer zemin sınıflarına göre daha fazladır. Ayrıca, ZE zemin sınıfı üzerine inşa edilen yapının periyodu Winkler yönteminde %75 daha fazla bulunmuştur. Bu artış deprem kuvvetlerinin artmasına neden olmaktadır. Yapıya etkiyen en büyük ivme sırasıyla ZE, ZD ve ZC zemin sınıfında olmuştur. Ankastre çözümde azaltılmış tasarım ivme değerleri Winkler yöntemine göre çözümden daha fazla olmuştur. Bu sebeple yapı-temel etkileşimini dikkate alan çözüm deprem kuvvetleri açısından daha ekonomik çözüm sunmakta fakat deplasmanlar daha fazla olmaktadır. Perde duvarların yalnız Eğik Çatlama Dayanımı (Vcr) bile deprem kuvvetinin üzerinde kalmaktadır. Bu durum tünel kalıp sistemlerin deprem etkisinde iyi performans göstermesini açıklamaktadır. ZC zemin sınıfında, düşey yükler altında oluşan gerilmeler ZE zemin sınıfına göre %25 daha fazladır. Deprem durumunda ise bu artış %50'ye kadar çıkmaktadır. Buna karşılık oturma değerleri artmaktadır.


  • A CASE STUDY: COST-BENEFIT AND RISK ANALYSES OF GABION WALL FOR ROCKFALL PROTECTION METHOD IN BOZKIR, TURKEY

    by Bekir Fidan, Yavuz Yenginar, Murat Olgun

    The construction of residential buildings, highways, and dams in the areas under the risk of rockfall constitutes a significant threat to life and property safety. Previously, the easiest solution for rockfall protection was to move the settlements in the regions under rockfall risk to another location although it was expensive. Another method is removing the rocks by hand, machine, or using explosives, since it is dangerous. Nowadays, various rock improvement methods of constructing barriers exist due to the developing technology and facilities. In the study, to resist the rockfall, a case study on analysis of a gabion wall in the Dereköy neighborhood of Bozkır District in Konya was presented. In the preliminary design stage, mapping studies, rock kinematic analyses, and the possible rockfall scenarios in the study area were carried out to determine the current conditions of the land before the construction works. The rockfall analysis shows that the rocks on the slope will reveal energy of 400-500 kJ, and the splash heights may vary between 30-150 cm. As a result of this data, a 420m-length and 3m-height gabion wall was constructed. The gabion wall, which has a 10000-kJ energy damping capacity, eliminates the risk of rockfall for 150 houses in the region. A huge cost-benefit has been achieved by constructing a gabion wall instead of other methods (expropriation of 150 houses or the surface coating with steel mesh) as a precaution against the hazard of rockfall in the study area.


  • Open Access

    The Use of Waste Materials Red Mud and Bottom Ash as Road Embankment Fill

    by Ali Sinan Soğancı, Ilyas Özkan, Yavuz Yenginar, Yusuf Güzel, Adnan Özdemir

    This study provides a comprehensive evaluation of red mud as a sustainable material for road base construction, particularly in combination with bottom ash. Red mud, a by-product of the Bayer process used in alumina extraction, is known for its high alkalinity and heavy metal content. For this reason, this waste material causes environmental challenges. Red mud sourced from the Eti Aluminum Factory in Seydişehir, Konya (Turkey), was stabilized with bottom ash. Then, these waste materials were tested through a number of experiments, such as in relation to their Atterberg limits, compaction characteristics, unconfined compressive strength (UCS), California bearing ratio (CBR), and microstructure through a scanning electron microscopy (SEM) analysis. The results highlight that the UCS of stabilized red mud samples significantly improved with the addition of bottom ash and longer curing periods. Specifically, the UCS values increased from 0.5 MPa to 2.5 MPa after 28 days of curing. Moreover, RM specimens stabilized with 25% bottom ash achieved a CBR value of 146.64% after 28 days, far exceeding Turkey’s road fill material requirement, which mandates a minimum unsoaked CBR value of 15%. These findings indicate that red mud stabilized with bottom ash not only meets but exceeds the structural requirements for road base materials. This approach provides a sustainable solution for the environmental management of red mud while contributing to infrastructure development. Through the recycling of these industrial by-products, this study presents a viable method to reduce waste and support economic and environmental sustainability in road construction projects.


  • Open Access

    Physical, mechanical, and microstructural characteristics of fly ash replaced cement deep mixing columns

    by Yavuz Yenginar, Murat Olgun

    The novel approach of the study is implementing the installation procedure of fly ash (FA) replaced cement deep mixing (DM) columns to field cases aiming at managing FA waste and reducing cement utilization. FA replaced cement DM columns (diameter of 30 cm and length of 80 cm) were installed on clayey soils using a laboratory type DM machine. The effect of installation parameters such as the binder dosage, FA replacement ratio, superplasticizer content, water/binder ratio, and the liquidity index (LI) of the soil on column performance was investigated. The design of experiments and optimization process were conducted using the Taguchi method, S/N and ANOVA analyses, and the desirability function method. Observations have shown that the mixing time required for a homogeneously mixed column depends on the LI of the soil and the volume ratio (VR) of the slurry. A key parameter (LI∙VR) is defined to decide the minimum number of the mixing process. The blade rotation number should be minimum of 252 rev/m to obtain a homogeneous soil-slurry mixture. The highest strength of the column was obtained when LI of fresh soilcrete (LImix) is 1.25∙LI. Optimum installation parameters were determined as binder dosage of 425 kg/m3, FA replacement ratio is 40%, superplasticizer content is 3%, water/binder ratio is 0.8, and LI of the untreated soil is 1. In the optimum design, the mixing efficiency of the soil-slurry mixture increased and the best column performance was obtained. In addition, cement utilization and binder cost decrease 40% and 33%, respectively, in FA-replaced cement DM columns. SEM images prove the increase in column performance due to the cementation products (CSH and CAH gels) formed in the microstructure of the column.


  • Open Access

    Uçucu Kül Katkısının Derin Karıştırma Kolonlarının Sıkışabilirliğine Etkisi

    by Yavuz Yenginar, Murat Olgun

    Sunulan bu çalışmanın özgün tarafı uçucu kül katkılı derin karıştırma kolonlarının (DKK) sıkışma kapasitesini en aza indirecek optimum enjeksiyon parametrelerini belirlemektir. Çalışmada killi bir zemin ıslak karıştırma yöntemiyle iyileştirilmiştir. Zeminin likitlik indisi, su/bağlayıcı oranı, çimento oranı, süper akışkanlaştırıcı miktarı ve uçucu kül ikame oranı gibi değişkenlerin DKK’nın sıkışabilirlik özelliğine etkisi incelenmiştir. Deneylerin tasarımı Taguchi yöntemine göre yapılmıştır. 5 parametre ve 4 seviye için L16 ortogonal dizin tablosuna göre DKK numuneleri hazırlanmıştır. Kürde bekletilen (28 ve 56 gün) numunelerin konsolidasyon deneyleri yapılarak numunenin sıkışma indisi, kabarma indisi ve boşluk oranındaki değişim belirlenmiştir. Analizler sonunda parametrelerin optimum değerleri (zeminin likitlik indisi=0.4, su/bağlayıcı oranı=0.8, bağlayıcı dozajı=425 kg/m3, süper akışkanlaştırıcı oranı=%3, uçucu kül oranı=%40) elde edilmiştir. Elde edilen sonuçlar DKK imalatında %40 oranında uçucu kül kullanılması ile enjeksiyon maliyetlerinin de bu oranda azalacağını göstermektedir. Ayrıca atık bir ürün olan uçucu kül kullanımının artması ile çevresel zararlar en aza inecektir.