SMSamal Muratova

Samal Muratova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Samal Muratova has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Automated system for continuous monitoring of drilling fluid parameters

    by S.K. Muratova, E.ZH. Omirzakova, G.K. Umirova, B.T. Ratov, A.E. Kuttybayev, Z.T. Mataeva, A.O. Zhailiev

    The aim of this study was to develop a hardware–software system for real-time automated monitoring of drilling fluid density, Marsh funnel viscosity, plastic viscosity, and yield point. An automated density measurement device was developed based on variations in the inductance of an electromagnetic system caused by the interaction between a magnetic core and fluids of different densities. Continuous data analysis methods and artificial intelligence algorithms were employed to evaluate rheological parameters. Laboratory and comparative tests were conducted using a standard Fann 35 viscometer at a temperature of 80°C. The developed system provided continuous measurement of drilling fluid parameters with an error not exceeding 2.5%, in compliance with API RP 13B-1 requirements. Comparison with the Fann 35 viscometer demonstrated deviations within the range of 3–5%. The system successfully identified abnormal operating conditions, including increases in viscosity and reductions in yield point, with a response time of less than 30 seconds. The obtained results confirmed the effectiveness of intelligent methods for predicting changes in the rheological properties of drilling fluids. The developed system improves the efficiency of drilling fluid parameter monitoring, minimizes the influence of the human factor, and enables integration into digital drilling management systems. The proposed technology also demonstrates significant potential for predicting drilling complications and expanding system functionality through the inclusion of additional monitoring parameters, such as pH and gas content.

  • DEVELOPMENT OF ALGORITHMS FOR CONTINUOUS MONITORING OF DRILLING FLUID VISCOSITY IN DYNAMIC CONDITION

    by Samal Muratova, Volodymyr Khomenko, Oleksandr Pashchenko, Zaira Matayeva, Zhanna Kenzhegalieva

    Drilling fluid viscosity is a critical parameter influencing the efficiency and safety of drilling operations, yet real-time monitoring under dynamic conditions remains challenging due to varying temperature, pressure, and flow rates. This study develops algorithms for continuous, automated viscosity monitoring of drilling fluids to optimize drilling processes. The primary objective is to design robust algorithms capable of accurate viscosity predictions in real-time, addressing limitations of traditional manual methods like the Fann 35 viscometer, which are labor-intensive and fail to capture rapid rheological changes. The methodology involves testing water-based and oil-based muds using inline viscometers, pressure transducers, and temperature sensors. Signal processing techniques, including low-pass filtering, and machine learning models, such as linear regression and neural networks, were developed to process sensor data and predict viscosity. The neural network model achieved accuracy (RMSE of 0.42 cP for water-based muds, 0.67 cP for oil-based muds in lab tests) compared to linear regression (RMSE of 0.85 cP and 1.12 cP). Tests confirmed robustness, with the neural network maintaining an RMSE of 0.58 cP and 0.79 cP. Statistical analysis using ANOVA and regression validated the results, demonstrating significant improvements over existing methods. The system enables real-time adjustments, enhancing drilling efficiency and safety. Future work includes improving algorithm adaptability and exploring edge computing for remote applications.

  • Optimization of drilling fluid density to reduce damage and contamination of productive layers

    by YESSENOV UNIVERSITY, Sarbopeyeva, Z.T. Mataeva, Satbayev University, M.M. Aliakbar, S.K. Muratova, A.E. Kuttybaev, A.O. Zhailiev, B.T. Ratov, M.T. Arshidinova, et al.

    This work considers maintaining the required density of drilling mud using weighting agents such as barium sulfate (BaSO4) as a key factor in ensuring wellbore stability and preventing complications during drilling. However, the introduction of barite into the drilling fluid can cause contamination of productive formations, reducing their permeability and productivity. Penetration of solid barite particles into the pore space leads to clogging of pores and filtration channels, which often becomes irreversible without specialized cleaning methods. To reduce the risk of contamination, it is necessary to optimize the composition of the drill-ing fluid and carefully control drilling parameters. The use of crystallization inhibitors, stabilizers, and polymer additives helps reduce barite sedimentation and decrease its adhesion to pore walls. This significantly lowers the likelihood of damage to productive intervals. In cases of existing contamination, restorative technologies are applied. Mechanical cleaning, including high-pressure well flushing, may be effective for surface-level clogging but has limited effectiveness for deep particle penetration. A more promising approach is the use of chelating agents capable of binding barium ions and breaking down barite deposits. The effectiveness of these reagents depends on the physical and chemical characteristics of the reservoir. An alternative solution involves specialized solvents designed for selective dissolution of barite in the pore space. Their application requires engineering justification and laboratory verifica-tion. A comprehensive approach, including optimization of the drilling fluid composition, control of technological parameters, and timely application of chemical reagents, helps maintain formation productivity and reduce operational costs during well drilling.

  • OPTIMIZATION OF DRILLING AND WELL DEVELOPMENT PROCESSES USING A SYSTEM OF DENSITY AND VISCOSITY SENSORS

    by Yessenov University, A.O. Zhailiev, S.K. Muratova, Satbayev University, E.ZH. Omirzakova, M.T. Tabylganov, A.G. Gusmanova, A.E. Kuttybaev, S.B. Ratova

    This work presents a digital density and viscosity sensor system (DVP) designed for highprecision real-time measurement of drilling fluid parameters. The technology plays a key role in ensuring the safety and efficiency of drilling operations due to its high sensitivity to changes in the properties of the environment and its resistance to flow rate fluctuations. This enables timely response to potential complications such as gas kicks, losses, clay swelling, and borehole instability, thereby minimizing the risks of accidents, reduced drilling rates, and equipment failure. The DVP system demonstrates stable and reliable performance under high-temperature and high-pressure conditions, where traditional methods of fluid parameter monitoring lose accuracy and reliability. Industrial trial results confirm that the implementation of this technology contributes to reducing drilling equipment downtime and enhances the reliability of hydrodynamic process monitoring and control. The system enables the acquisition of accurate real-time data, significantly improving technical decision-making processes. Integration of the DVP system with automated well control systems allows for trend analysis, predictive modeling, and remote monitoring of well conditions. This creates the foundation for more accurate management of drilling fluid properties and optimization of technological processes. The system is particularly effective in deepwater and offshore field development, where the cost of er-rors and downtime is especially high. The use of DVP contributes to reducing operational costs, increasing productivity, improving environmental performance, and promoting the sustainable de-velopment of hydrocarbon extraction.

  • Preparation of CrB2 mixtures and formation of briquettes for drill bit composites

    by Satbayev University, B.T. Ratov, A.E. Kuttybaev, S.K. Muratova, Sarbopeyeva, Yessenov University, A.B. Kalzhanova, A.A. Zhangirkhanova

    The research described in the article concerns advanced methods of creating composite materials for drill bits used in extreme conditions of deep wells. The main attention is paid to development of multicomponent mixtures that ensure uniform distribution of powders of tungsten carbide, cobalt, chromium diboride and diamond. This is achieved through careful selection of particle size and proportions, which is critically important to ensure high strength and wear resistance of final materials. The Spark Plasma Sintering (SPS) method was chosen for the production of samples of carbide matrices and composite diamond-containing materials because of its ability to provide high density and uniformity of the material. SPS allows temperature and pressure control during sintering process, which contributes to the formation of materials with optimal physical properties. The article also discusses in detail design parameters of the diamond bit, including the choice of grain size of diamond powder and other components. These meters have been optimized to max-imize drilling efficiency and extend tool life. The diamond powders used in study were obtained from De Beers, South Africa and are characterized by high quality and uniformity. The results presented in the article can have a significant impact on future production of drilling tools, offering new approaches to choice of materials and methods of their processing, which ultimately can lead lower drilling costs and increased process safety. These innovations can also contribute to more efficient development of new fields, which is of great importance for the energy industry and the mining industry.

  • The choice of optimal methods for the development of water wells in the conditions of the Tonirekshin field (Kazakhstan)

    by M. T Biletskiy, B. T Ratov, V. L Khomenko, A. R Borash, S. K Muratova

    New+Mining +https://doi.org/10.33271/nvngu/2024-1 +/jdownloads/pdf/2024/1/01_2024_contents-en-GB.pdf


  • NEW DRILLING METHOD, DEVELOPMENT OF HYDROGEOLOGICAL AND OIL WELLS WITH IMPLOSIVE EFFECT

    by SATBAYEV UNIVERSITY, B.T. Ratov, M.T. Biletskiy, A.T. Makyzhanova, A.R. Borash, YESSENOV UNIVERSITY, S.K. Muratova

    The peculiarities of the collimation zones of the productive formation are taken into account when rotary drilling of wells using drilling mud. A brief analysis of the most common and fundamentally different decollatation procedures, such as washing wells with water, pumping and gelation, is presented. A very effective and promising method of decollatation using the implosion effect has a special influence. A detailed example of a well-known device is given with an analysis of the features of its application, as well as significant disadvantages in the form of complexity and functionality, high cost. A fundamentally different new device was developed and proposed, free from all the disadvantages of the opposite device for which the invention was requested. This eliminates the use of pumping and compressor pipes and their sealing, as well as a sealant for the neck. There is also no need for a compressor and surface wiring with numerous valves. Replacing the intake valve valve with a disc valve eliminates the possibility of closing the intake valve as a result of the influx of reservoir fluid with a high content of collating materials caused by the implosion effect. The design and functioning features of the proposed device and its individual elements are taken into account both when creating a single, and with any number of repeated implosive effects. The generation limits necessary for the explosion effect of the liquid-filled space were mathematically analyzed to prevent the case from crumpling under the hydrostatic pressure of the solution remaining in the storage space. An example of the dependence of the permissible length of empty space on the thickness of the housing column and, in particular, on the thickness of the walls is illustrated using a computer program.

  • Open Access

    Calculations on Enhancement of Polycrystalline Diamond Bits through Addition of Superhard Diamond-Reinforced Elements

    by Boranbay Ratov, Miroslaw Rucki, Boris Fedorov, Edvin Hevorkian, Zbigniew Siemiatkowski, Samal Muratova, Elmira Omirzakova, Aidar Kuttybayev, Vladimir Mechnik, Nikolai Bondarenko

    The paper is dedicated to the enhancement of Polycrystalline Diamond Bits (PDC) designed for oil and gas industry. A novel diamond-reinforced composite was applied for cutting inserts, with the addition of 4 wt% chromium diboride to the WC-Co matrix. The addition of CrB2 ensured improvement of bending strength and fracture toughness by nearly 30% and 40%, respectively, and enhanced the diamond retention force. The efficiency of PDC bits was further improved by incorporating constructional features in both bottomhole and reaming parts. An analytical relationship between the feeding speed and geometrical parameters was found, including the wings and calibrating inserts numbers, as well as the rotational speed of the cutter. Under the conditions of rock fracture by reaming inserts, the approximate value of the required power was calculated.