Zuguang Guan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zuguang Guan has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Daru Chen
Zhejiang Normal University
6 shared publications - Qiang Ling
Zhejiang Normal University
6 shared publications - Zhangwei Yu
Zhejiang Normal University
4 shared publications - Anping Xiao
Hangzhou Institute of advanced studies, Zhejiang Normal University, Hangzhou, China
3 shared publications - Weixuan Luo
Hangzhou Institute of Advanced Studies, Zhejiang Normal University, 1108 Geng Wen Road, Hangzhou 311231, China
3 shared publications - Bin Zhang
Hangzhou Institute of Advanced Studies, Zhejiang Normal University, Hangzhou, 311231, China
2 shared publications
Latest Publications
- Open Access
A Composite Sagnac Fiber Loop for Gas Pressure Sensing
A novel optical fiber sensor, based on a composed-type Sagnac loop for gas pressure sensing, has been introduced and experimentally validated. This sensor consists of a centimeter-scale twin-hole and dual-core fiber (THDCF) sandwiched by two segments of polarization-maintaining fibers (PMFs) via splicing. Given that the pure quartz PMF is insensitive to the variations in gas pressure, it is unsuitable for gas pressure sensing. To improve the sensitivity, a short piece of THDCF is added to the PMF-based Sagnac loop. Theoretical analysis has demonstrated that the presence of THDCF could significantly amplify the impact of air pressure on birefringence. Experimental results reveal that as the ambient gas pressure rises from 0 to 1.2 MPa, the interference spectrum exhibits an obvious red shift with a high sensitivity of 8.381 nm/MPa. The sensor’s reliability has undergone repeated verification by increasing and decreasing the pressure. Attributed to its simple structure, easy fabrication, low cost, and high sensitivity, the proposed sensor is particularly suited for development in harsh environments.
Open AccessA Composite Sagnac Fiber Loop for Gas Pressure Sensing
A novel optical fiber sensor, based on a composed-type Sagnac loop for gas pressure sensing, has been introduced and experimentally validated. This sensor consists of a centimeter-scale twin-hole and dual-core fiber (THDCF) sandwiched by two segments of polarization-maintaining fibers (PMFs) via splicing. Given that the pure quartz PMF is insensitive to the variations in gas pressure, it is unsuitable for gas pressure sensing. To improve the sensitivity, a short piece of THDCF is added to the PMF-based Sagnac loop. Theoretical analysis has demonstrated that the presence of THDCF could significantly amplify the impact of air pressure on birefringence. Experimental results reveal that as the ambient gas pressure rises from 0 to 1.2 MPa, the interference spectrum exhibits an obvious red shift with a high sensitivity of 8.381 nm/MPa. The sensor’s reliability has undergone repeated verification by increasing and decreasing the pressure. Attributed to its simple structure, easy fabrication, low cost, and high sensitivity, the proposed sensor is particularly suited for development in harsh environments.
- Open Access
- 12 November 2025
- Published by MDPI AG in Preprints.org
A Composite Sagnac Fiber Loop for Gas Pressure Sensing
A novel optical fiber sensor, based on a composed-type Sagnac loop for gas pressure sensing, has been introduced and experimentally validated. This sensor consists of a centimeter-scale twin-hole and dual-core fiber (THDCF) sandwiched by two segments of polarization-maintaining fibers (PMFs) via splicing. Given that the pure quartz PMF is insensitive to the variations in gas pressure, it is unsuitable for the gas pressure sensing. To improve the sensitivity, a short piece of THDCF is added to the PMF-based Sagnac loop. Theoretical analysis has demonstrated that the presence of THDCF could significantly amplify the impact of air pressure on birefringence. Experimental results reveal that as the ambient gas pressure rises from 0-1.2 MPa, the interference spectrum exhibits an obvious red-shift with a high sensitivity of 8.381 nm/MPa. The sensor’s reliability has undergone repeated verification by increasing and decreasing the pressure. Attributed to its simple structure, easy fabrication, low cost and high sensitivity, the proposed sensor is particularly suited for development in harsh environments.
- 12 November 2025
- Published by MDPI AG in Preprints.org
Open AccessA Composite Sagnac Fiber Loop for Gas Pressure Sensing
A novel optical fiber sensor, based on a composed-type Sagnac loop for gas pressure sensing, has been introduced and experimentally validated. This sensor consists of a centimeter-scale twin-hole and dual-core fiber (THDCF) sandwiched by two segments of polarization-maintaining fibers (PMFs) via splicing. Given that the pure quartz PMF is insensitive to the variations in gas pressure, it is unsuitable for the gas pressure sensing. To improve the sensitivity, a short piece of THDCF is added to the PMF-based Sagnac loop. Theoretical analysis has demonstrated that the presence of THDCF could significantly amplify the impact of air pressure on birefringence. Experimental results reveal that as the ambient gas pressure rises from 0-1.2 MPa, the interference spectrum exhibits an obvious red-shift with a high sensitivity of 8.381 nm/MPa. The sensor’s reliability has undergone repeated verification by increasing and decreasing the pressure. Attributed to its simple structure, easy fabrication, low cost and high sensitivity, the proposed sensor is particularly suited for development in harsh environments.
- Open Access
- 13 March 2025
- Published by Cambridge University Press (CUP) in Radiocarbon
- Vol. 67 (3) , 565-577
Laser spectroscopy: A potential versatile solution for radiocarbon analyses
Radiocarbon (14C) measurements play important roles in dating and tracing applications where the isotopic concentration can differ from 0.1 to 106 pMC (percent modern carbon). A liquid scintillation counter cannot provide enough sensitivity when dealing with low-concentration samples of limited amounts over a reasonable time period. Accelerator mass spectroscopy (AMS) measures low-concentrations well but must first do dilution for high-concentration samples, and suffers from high instrument and maintenance costs. Saturated absorption CAvity Ring-down spectroscopy (SCAR) has now been developed into a practical technique with performances close to AMS but at much lower costs. The dynamic range covers 1–105 pMC, and the measurement uncertainties in the range of 0.4–1 pMC can be achieved within 0.5–2.5 hr of operation time. SCAR measures CO2 gases directly without graphitization in sample preparation. The typical sample consumption is ∼1 mg of carbon mass and the time for sample preparation can be as short as 15 min. Applications of SCAR to Suess-effect evaluation, biogenic-component analysis, ancient- and modern-sample dating, food-fraud detection and medicine-metabolism study have all been demonstrated by employing a close-to-automatic sample preparation system.
- 13 March 2025
- Published by Cambridge University Press (CUP) in Radiocarbon
- Vol. 67 (3) , 565-577
Open AccessLaser spectroscopy: A potential versatile solution for radiocarbon analyses
Radiocarbon (14C) measurements play important roles in dating and tracing applications where the isotopic concentration can differ from 0.1 to 106 pMC (percent modern carbon). A liquid scintillation counter cannot provide enough sensitivity when dealing with low-concentration samples of limited amounts over a reasonable time period. Accelerator mass spectroscopy (AMS) measures low-concentrations well but must first do dilution for high-concentration samples, and suffers from high instrument and maintenance costs. Saturated absorption CAvity Ring-down spectroscopy (SCAR) has now been developed into a practical technique with performances close to AMS but at much lower costs. The dynamic range covers 1–105 pMC, and the measurement uncertainties in the range of 0.4–1 pMC can be achieved within 0.5–2.5 hr of operation time. SCAR measures CO2 gases directly without graphitization in sample preparation. The typical sample consumption is ∼1 mg of carbon mass and the time for sample preparation can be as short as 15 min. Applications of SCAR to Suess-effect evaluation, biogenic-component analysis, ancient- and modern-sample dating, food-fraud detection and medicine-metabolism study have all been demonstrated by employing a close-to-automatic sample preparation system.
- Open Access
- 27 January 2025
- Published by MDPI AG in Atmosphere
- Vol. 16 (2) , 138
Detection of Atmospheric NO2 Using Scheimpflug DIAL with a Blue External Cavity Diode Laser Source
Nitrogen dioxide (NO2) is broadly acknowledged as one of the six key air pollutants, posing a significant threat to environmental stability and human health. The profile of atmospheric nitrogen dioxide is required for quantifying NO2 emissions from fossil fuel combustion and industry. In continuous-wave differential absorption lidar (CW-DIAL) systems, the laser sources employed are subject to the issues of varying output characteristics and poor instability. This study presents a CW-DIAL system for remote sensing of atmospheric NO2 that employs a compact grating-based external cavity diode laser (ECDL) and Scheimpflug imaging. The laser in this system utilizes a piezoelectric transducer (PZT) for precise wavelength tuning, emitting at 448.1 nm and 449.7 nm with an output power of 2.97 W and a narrow linewidth of 0.16 nm. Signal capturing was achieved through a Newtonian telescope with a diameter of 200 mm and a 45° inclined CCD image sensor, satisfying the Scheimpflug principle. A case study near road traffic was used to verify the feasibility of ECDL-DIAL, which took place from 1 October to 2 October 2023 over an industrial park. The system generates precise NO2 distribution maps with sub-50 m resolution over 3 km, updating every 10 min.
- 27 January 2025
- Published by MDPI AG in Atmosphere
- Vol. 16 (2) , 138
Open AccessDetection of Atmospheric NO2 Using Scheimpflug DIAL with a Blue External Cavity Diode Laser Source
Nitrogen dioxide (NO2) is broadly acknowledged as one of the six key air pollutants, posing a significant threat to environmental stability and human health. The profile of atmospheric nitrogen dioxide is required for quantifying NO2 emissions from fossil fuel combustion and industry. In continuous-wave differential absorption lidar (CW-DIAL) systems, the laser sources employed are subject to the issues of varying output characteristics and poor instability. This study presents a CW-DIAL system for remote sensing of atmospheric NO2 that employs a compact grating-based external cavity diode laser (ECDL) and Scheimpflug imaging. The laser in this system utilizes a piezoelectric transducer (PZT) for precise wavelength tuning, emitting at 448.1 nm and 449.7 nm with an output power of 2.97 W and a narrow linewidth of 0.16 nm. Signal capturing was achieved through a Newtonian telescope with a diameter of 200 mm and a 45° inclined CCD image sensor, satisfying the Scheimpflug principle. A case study near road traffic was used to verify the feasibility of ECDL-DIAL, which took place from 1 October to 2 October 2023 over an industrial park. The system generates precise NO2 distribution maps with sub-50 m resolution over 3 km, updating every 10 min.
- Open Access
Angularly Cascaded Long-Period Fiber Grating for Curvature and Temperature Detection
A high-sensitivity curvature sensor with dual-parameter measurement ability based on angularly cascaded long-period fiber grating (AC-LPFG) is proposed and experimentally demonstrated, which consists of two titled LPFGs (TLPFGs) with different tilt angles and the same grating period. AC-LPFG was fabricated by using a deep ultraviolet laser and an amplitude-mask in our laboratory. The experimental results show that simultaneous measurement of curvature and temperature can be achieved by monitoring the wavelengths of two resonant peaks for different TLPFGs. The two peaks show opposite shifts with increasing curvature and has a maximum curvature sensitivity of 16.392 nm/m−1. With the advantages of low cost, high sensitivity, and dual-parameter measurements, our sensor has more potential for engineering applications.
Open AccessAngularly Cascaded Long-Period Fiber Grating for Curvature and Temperature Detection
A high-sensitivity curvature sensor with dual-parameter measurement ability based on angularly cascaded long-period fiber grating (AC-LPFG) is proposed and experimentally demonstrated, which consists of two titled LPFGs (TLPFGs) with different tilt angles and the same grating period. AC-LPFG was fabricated by using a deep ultraviolet laser and an amplitude-mask in our laboratory. The experimental results show that simultaneous measurement of curvature and temperature can be achieved by monitoring the wavelengths of two resonant peaks for different TLPFGs. The two peaks show opposite shifts with increasing curvature and has a maximum curvature sensitivity of 16.392 nm/m−1. With the advantages of low cost, high sensitivity, and dual-parameter measurements, our sensor has more potential for engineering applications.
- Open Access
An Axial Force Sensor Based on a Long-Period Fiber Grating with Dual-Peak Resonance
A high-sensitivity axial force sensor with a large measurement range based on a dual-peak long-period fiber grating (LPFG) is proposed and experimentally demonstrated. Previously, the relationship between the grating period and the dual-peak wavelengths has been investigated based on the coupled-mode theory. In our experiment, the LPFG was fabricated in our laboratory by illuminating the fiber core with the aid of a 213 nm UV laser. The sensitivity of the proposed axial force sensor can reach −14.047 nm/N in the force range from 0.490 N to 4.508 N. Taking the advantages of a compact size, low cost, and large measurement range, our force sensor has more applicable abilities in harsh environments.
Open AccessAn Axial Force Sensor Based on a Long-Period Fiber Grating with Dual-Peak Resonance
A high-sensitivity axial force sensor with a large measurement range based on a dual-peak long-period fiber grating (LPFG) is proposed and experimentally demonstrated. Previously, the relationship between the grating period and the dual-peak wavelengths has been investigated based on the coupled-mode theory. In our experiment, the LPFG was fabricated in our laboratory by illuminating the fiber core with the aid of a 213 nm UV laser. The sensitivity of the proposed axial force sensor can reach −14.047 nm/N in the force range from 0.490 N to 4.508 N. Taking the advantages of a compact size, low cost, and large measurement range, our force sensor has more applicable abilities in harsh environments.
- Open Access
All-Solid Single-Polarization Anti-Resonant Fiber Base on Anisotropic Glass
A single-polarization solid-core anti-resonant fiber is proposed, and the influence of the fiber core material anisotropy of the solid-core anti-resonant fiber on polarization characteristics is investigated using the finite element method. Single-polarization guidance is achieved by using the anisotropy of optical fiber materials, which also ensures high birefringence. The numerical simulation results indicate that there are two single-polarization intervals (1210–1440 nm and 1490–1560 nm), with a maximum bandwidth of up to 230 nm, when the confinement loss difference between the two orthogonal polarizations exceeds two orders of magnitude. Specifically, when the work wavelength is 1550 nm, a polarization extinction ratio (PER) of 108 is obtained by optimizing the structure parameters. Additionally, the y-polarization fundamental mode (YPFM) can be well confined in the fiber center with a low confinement loss of 0.04 dB/m, while the x-polarization fundamental mode (XPFM) has a huge confinement loss larger than 4.65 dB/m due to the coupling with the tube mode. The proposed single-polarization solid-core anti-resonant fiber has a huge potential in applications such as laser systems, fiber-optic gyroscopes, and optical fiber communications.
Open AccessAll-Solid Single-Polarization Anti-Resonant Fiber Base on Anisotropic Glass
A single-polarization solid-core anti-resonant fiber is proposed, and the influence of the fiber core material anisotropy of the solid-core anti-resonant fiber on polarization characteristics is investigated using the finite element method. Single-polarization guidance is achieved by using the anisotropy of optical fiber materials, which also ensures high birefringence. The numerical simulation results indicate that there are two single-polarization intervals (1210–1440 nm and 1490–1560 nm), with a maximum bandwidth of up to 230 nm, when the confinement loss difference between the two orthogonal polarizations exceeds two orders of magnitude. Specifically, when the work wavelength is 1550 nm, a polarization extinction ratio (PER) of 108 is obtained by optimizing the structure parameters. Additionally, the y-polarization fundamental mode (YPFM) can be well confined in the fiber center with a low confinement loss of 0.04 dB/m, while the x-polarization fundamental mode (XPFM) has a huge confinement loss larger than 4.65 dB/m due to the coupling with the tube mode. The proposed single-polarization solid-core anti-resonant fiber has a huge potential in applications such as laser systems, fiber-optic gyroscopes, and optical fiber communications.