ASAgnese Spustaka

Agnese Spustaka

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Agnese Spustaka has a total of 8 co-authors. Here are the top co-authors by number of shared publications:

  • Aleksejs Zolotarjovs

    Institute of Solid State Physics, University of Latvia, Kengaraga Str. 8, LV-1063 Riga, Latvia

    1 shared publication
  • D. Millers

    Institute of Solid State Physics , University of Latvia , 8 Kengaraga Str., Riga LV-1063 , Latvia

    1 shared publication
  • Ernests Einbergs

    Institute of Solid State Physics, University of Latvia, Ķengaraga Iela 8, Latgales Priekšpilsēta, LV-1063 Rīga, Latvia

    1 shared publication
  • I. Bite

    Institute of Solid State Physics , University of Latvia , 8 Kengaraga Str., Riga LV-1063 , Latvia

    1 shared publication
  • K. Smits

    Institute of Solid State Physics , University of Latvia , 8 Kengaraga Str., Riga LV-1063 , Latvia

    1 shared publication
  • M. Senko

    Institute of Solid State Physics , University of Latvia , 8 Kengaraga Str., Riga LV-1063 , Latvia

    1 shared publication

Latest Publications

  • Open Access

    By Visualizing the Deformation with Mechanoluminescent Particles, Additive Manufacturing Offers a Practical Alternative to Stress and Strain Simulation

    by Ernests Einbergs, Agnese Spustaka, Virginija Vitola, Aleksejs Zolotarjovs

    The use of stress–strain analysis in structural design or mechanical components is critical for avoiding or investigating structural failures. In the case of complicated designs, mathematical full-field stress modeling produces imprecise predictions. Experimental analysis can be used as a replacement for mathematical modeling, but with the use of currently available strain gauges, it is cumbersome and impossible in the case of moving parts. Mechanoluminescent materials transform mechanical energy into visible light and can be used as a replacement for strain gauges to monitor strain/stress. Three-dimensional printing technology has made major advances in terms of additive manufacturing. In this article, we describe a method to produce an ML 3D print. The fabricated samples are precise and versatile and satisfy the need for easy and non-destructible spatial stress analysis. A 3D printed photopolymer sample with SrAl2O4: Eu, Dy particle addition only to the final layers was tested, and the number of layers was optimized. It was determined that the optimal number of layers for easy detection is in the range of 10 to 20 layers. It opens the possibility for the real-time evaluation of complex uneven forces on complex parts, thus having a good potential for commercialization.


  • Open Access

    GALLIUM CONCENTRATION OPTIMISATION OF GALLIUM DOPED ZINC OXIDE FOR IMPROVEMENT OF OPTICAL PROPERTIES

    by A. Spustaka, M. Senko, D. Millers, I. Bite, K. Smits, V. Vitola

    The near-band luminescence of doped ZnO is promising for advanced scintillators; however, the dopant type and concentration effects require a detailed study. Undoped and Ga-doped ZnO nanopowders were prepared by a microwave-assisted solvothermal method and the gallium concentration effect on luminescence properties was studied. The near-band luminescence peak position dependence on gallium concentration was observed. Near-band luminescence intensity versus defect luminescence intensity ratio was explored for different gallium concentrations and the optimal value was determined. Samples were prepared with dopant concentrations between 0.2 and 1.5 at%, XRD analysis confirmed that samples contained only zinc oxide hexagonal wurtzite phase. The results of the research showed that ZnO:Ga containing 0.9 at.% gallium was promising for scintillators.