Feiyu Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Feiyu Li has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Caisheng Fan
School of Information Engineering, Wuhan University of Technology, China
2 shared publications - Xue-Dong Liu
School of Information Engineering, Wuhan University of Technology, China
2 shared publications - Yuxin Liang
School of Information Engineering, Wuhan University of Technology, China
2 shared publications - Huixin Dong
Huazhong University of Science and Technology, Wuhan, China
1 shared publication - Qian Zhang
Hong Kong University of Science and Technology, Hong Kong, Hong Kong
1 shared publication - Runze Sun
Wuhan University of Technology, China
1 shared publication
Latest Publications
- Open Access
- 3 November 2025
- Published by Association for Computing Machinery (ACM)
- p. 139-153
PassiveBLE: Towards Fully Commodity Compatible BLE Backscatter
- 3 November 2025
- Published by Association for Computing Machinery (ACM)
- p. 139-153
Open AccessPassiveBLE: Towards Fully Commodity Compatible BLE Backscatter
- Open Access
- 4 November 2022
- Published by Association for Computing Machinery (ACM)
- p. 445-451
Realization of Fuzzy PID Controller on FPGA for Source Measurement Unit
The classic Source Measurement Unit's (SMU: Source Measurement Unit) shortcomings include a sluggish transient response and a significant overshoot. This paper proposed an optimization method that made use of fuzzy PID controller on FPGA for SMU. With the aid of the software Matlab, we first analyzed the SMU's circuit diagram and obtained the system's transfer function. Next, we constructed the system simulation model adjusted by a fuzzy PID controller in Simulink. The initial P, I, and D parameters were obtained by the PID tuner, and they were adjusted by the fuzzy controller until they can achieve the optimal performance. Finally, we designed a Verilog program with the initial parameters to implement the fuzzy PID controller, in which the parameters were modified dynamically according to error and its increment to make sure they were optimal. We tested the controller using the HDL simulation tool Modelsim to ensure the simulation results matched those from Simulink. The results of simulation showed that the proposed method outperformed the conventional approach. In detail, our fuzzy PID controller can achieve shorter rising time, shorter setting time, and smaller overshoot than the NI SourceAdapt technology does.
- 4 November 2022
- Published by Association for Computing Machinery (ACM)
- p. 445-451
Open AccessRealization of Fuzzy PID Controller on FPGA for Source Measurement Unit
The classic Source Measurement Unit's (SMU: Source Measurement Unit) shortcomings include a sluggish transient response and a significant overshoot. This paper proposed an optimization method that made use of fuzzy PID controller on FPGA for SMU. With the aid of the software Matlab, we first analyzed the SMU's circuit diagram and obtained the system's transfer function. Next, we constructed the system simulation model adjusted by a fuzzy PID controller in Simulink. The initial P, I, and D parameters were obtained by the PID tuner, and they were adjusted by the fuzzy controller until they can achieve the optimal performance. Finally, we designed a Verilog program with the initial parameters to implement the fuzzy PID controller, in which the parameters were modified dynamically according to error and its increment to make sure they were optimal. We tested the controller using the HDL simulation tool Modelsim to ensure the simulation results matched those from Simulink. The results of simulation showed that the proposed method outperformed the conventional approach. In detail, our fuzzy PID controller can achieve shorter rising time, shorter setting time, and smaller overshoot than the NI SourceAdapt technology does.
- Open Access
- 4 November 2022
- Published by Association for Computing Machinery (ACM)
- p. 438-444
Modeling and Simulation of The Source Measure Unit Based on Simulink
Source measure unit (SMU) is a comprehensive instrument that provides functions such as measuring and supplying voltage and current sources. As the electronics research industry increases its requirements for product measurement and power supply, there is an urgent demand for better performance of the SMU control system. Based on the high cost and difficulty of entity optimization, this paper proposes the utilization of circuit analysis and Simulink to model and simulate the control system. Based on the foundation of PID control, the role of each control link is discussed in this paper. The simulation results show that PID control module can effectively optimize the performance of the SMU transient response by adjusting PID parameters under the input disturbance. On the basis of Simulink model, it is more convenient to improve the SMU and obtain a stable signal for the device under test, so that the SMU can better serve the electrical test field.
- 4 November 2022
- Published by Association for Computing Machinery (ACM)
- p. 438-444
Open AccessModeling and Simulation of The Source Measure Unit Based on Simulink
Source measure unit (SMU) is a comprehensive instrument that provides functions such as measuring and supplying voltage and current sources. As the electronics research industry increases its requirements for product measurement and power supply, there is an urgent demand for better performance of the SMU control system. Based on the high cost and difficulty of entity optimization, this paper proposes the utilization of circuit analysis and Simulink to model and simulate the control system. Based on the foundation of PID control, the role of each control link is discussed in this paper. The simulation results show that PID control module can effectively optimize the performance of the SMU transient response by adjusting PID parameters under the input disturbance. On the basis of Simulink model, it is more convenient to improve the SMU and obtain a stable signal for the device under test, so that the SMU can better serve the electrical test field.
- Open Access
- 4 November 2022
- Published by Association for Computing Machinery (ACM)
- p. 469-476
Hoist Wire Rope Fault Detection System Based on Wavelet Threshold and SVD Denoising
Mine hoist is an important conveying large mechanical equipment, which mainly drives the steel wire rope to drive the container up and down in the shaft to complete the conveying task and is widely used in engineering. However, the performance change of wire rope has an important impact on the requirements and safety of the entire conveying task. This paper uses wavelet threshold method and SVD to denoise the signal, so as to study the monitoring data of six rope hoist after noise removal and the number, degree and location of all defects of six wire ropes after 10 round trips. The obtained signals are used to detect outliers, detect the number and location of defects, and determine the size and type of defects according to the definition of defects. Use Topsis method and entropy weight method to evaluate the safety performance of the rope, and discuss the influence of relevant parameters on the safety performance of the wire rope. According to the calculation, the safety performance of the second rope is the worst, and the safety performance of the fifth and sixth ropes is the best.
- 4 November 2022
- Published by Association for Computing Machinery (ACM)
- p. 469-476
Open AccessHoist Wire Rope Fault Detection System Based on Wavelet Threshold and SVD Denoising
Mine hoist is an important conveying large mechanical equipment, which mainly drives the steel wire rope to drive the container up and down in the shaft to complete the conveying task and is widely used in engineering. However, the performance change of wire rope has an important impact on the requirements and safety of the entire conveying task. This paper uses wavelet threshold method and SVD to denoise the signal, so as to study the monitoring data of six rope hoist after noise removal and the number, degree and location of all defects of six wire ropes after 10 round trips. The obtained signals are used to detect outliers, detect the number and location of defects, and determine the size and type of defects according to the definition of defects. Use Topsis method and entropy weight method to evaluate the safety performance of the rope, and discuss the influence of relevant parameters on the safety performance of the wire rope. According to the calculation, the safety performance of the second rope is the worst, and the safety performance of the fifth and sixth ropes is the best.