Hasan Ballikaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hasan Ballikaya has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Cetin Ozay
Elazig , Turkey
2 shared publications - Mehmet Altuğ
Inonu University
2 shared publications - Ahmet Yesil
Department of Mechanical Engineering, Engineering Faculty, Firat University, Elazig 23200, Turkey
1 shared publication Cetin Ozay
Firat University Faculty of Technology Mechanical Engineering Department
1 shared publication- Mehmet Fatih Şahan
ADIYAMAN ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, İNŞAAT MÜHENDİSLİĞİ BÖLÜMÜ
1 shared publication - Mete Onur Kaman
Firat University
1 shared publication
Latest Publications
- Open Access
- 27 April 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 134 (1) , 88
Repair of Cracked Composites and Investigation of Their Performances Under Impact Load
In this study, composite plates with circular holes cracked on both edges were repaired using a composite patch. Epoxy adhesive was used to bond the patch to the plate. Low-velocity impact tests were applied to repaired specimens with varying crack lengths. Compared to specimens without holes, the maximum reaction force of repaired specimens without cracks increased by up to 50%. When the crack length reached its maximum, the maximum impact force of repaired specimens increased by 36% compared to the specimens without holes.
- 27 April 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 134 (1) , 88
Open AccessRepair of Cracked Composites and Investigation of Their Performances Under Impact Load
In this study, composite plates with circular holes cracked on both edges were repaired using a composite patch. Epoxy adhesive was used to bond the patch to the plate. Low-velocity impact tests were applied to repaired specimens with varying crack lengths. Compared to specimens without holes, the maximum reaction force of repaired specimens without cracks increased by up to 50%. When the crack length reached its maximum, the maximum impact force of repaired specimens increased by 36% compared to the specimens without holes.
- 4 October 2024
- Published by Springer Nature in Sādhanā
- Vol. 49 (4) , 1-11
Microstructure and wear behaviour of Al/SiC composite coating on AlZn5.5MgCu alloy substrate at different sintering temperatures
- 4 October 2024
- Published by Springer Nature in Sādhanā
- Vol. 49 (4) , 1-11
Microstructure and wear behaviour of Al/SiC composite coating on AlZn5.5MgCu alloy substrate at different sintering temperatures
- 29 January 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (4) , 553-566
Effect of particle volume fraction on wear behavior in Al–SiC MMC coated on DIN AlZnMgCu1.5 alloy
In this study, DIN AlZnMgCu1.5 alloy surface (Al + SiC) was coated with metal matrix composite (MMC) by using hot press sintering method (HPSM). Al was used as matrix material and SiC powders were used as reinforcing material in the coating process on DIN AlZnMgCu1.5 alloy surface. Al/SiC MMC coating was produced at 600 °C under 120 MPa pressure and with varying SiC content (5, 10 and 15 vol.%). Optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) were used to examine the microstructure, elemental analysis and phase structure of both the coating zone and the transition zone between the substrate and the coating. The hardness was measured and a dry sliding linear reciprocating wear test was run to determine the mechanical properties of the coating layer. Consequently, the coefficient of friction (COF) and wear volume were determined. OM and SEM images showed a homogeneous distribution of SiC particles and a less porous structure. The hardness of the MMC coating increased with increasing SiC content. Also, the numerical analysis of the wear test simulation was done based on Archard’s law. The results of both wear tests showed that the volume loss values were consistent with each other and the amount of wear significantly reduced by increasing the rate of SiC reinforcement.
- 29 January 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (4) , 553-566
Effect of particle volume fraction on wear behavior in Al–SiC MMC coated on DIN AlZnMgCu1.5 alloy
In this study, DIN AlZnMgCu1.5 alloy surface (Al + SiC) was coated with metal matrix composite (MMC) by using hot press sintering method (HPSM). Al was used as matrix material and SiC powders were used as reinforcing material in the coating process on DIN AlZnMgCu1.5 alloy surface. Al/SiC MMC coating was produced at 600 °C under 120 MPa pressure and with varying SiC content (5, 10 and 15 vol.%). Optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) were used to examine the microstructure, elemental analysis and phase structure of both the coating zone and the transition zone between the substrate and the coating. The hardness was measured and a dry sliding linear reciprocating wear test was run to determine the mechanical properties of the coating layer. Consequently, the coefficient of friction (COF) and wear volume were determined. OM and SEM images showed a homogeneous distribution of SiC particles and a less porous structure. The hardness of the MMC coating increased with increasing SiC content. Also, the numerical analysis of the wear test simulation was done based on Archard’s law. The results of both wear tests showed that the volume loss values were consistent with each other and the amount of wear significantly reduced by increasing the rate of SiC reinforcement.
- Open Access
- 17 August 2023
- Published by El-Cezeri: Journal of Science and Engineering in El-Cezeri Fen ve Mühendislik Dergisi
- Vol. 10 (3) , 475-491
Investigation of Sheet Thickness and Punch Force in Die Surface Angled Hydro-mechanical Deep Drawing Method
In this study, the effect of die surface angled hydro-mechanical deep drawing method (HMDDM) on sheet metal cup wall thickness and punch force was investigated as experimental and numerical analysis. In the works, 0.9 mm thick DIN EN 10130-1999 sheet metal material was used. The effect of variables on the test results was investigated by using die surface/blank holder angle, punch nose radius, die shoulder radius, chamber pressure and blank holder force as experimental parameters. Numerical analysis experiments were carried out using ANSYS 15.0 package program. Besides, experiments were performed according to the Taguchi experiment plan and L18 orthogonal array. The obtained data were analysed statistically by ANOVA analysis of variance in MINITAB 17.0 package program, and the effect of each parameter on the results was determined as a percentage. As a result, it was determined that the thinning was approximately 15% at most and the thickening was 10%.
- 17 August 2023
- Published by El-Cezeri: Journal of Science and Engineering in El-Cezeri Fen ve Mühendislik Dergisi
- Vol. 10 (3) , 475-491
Open AccessInvestigation of Sheet Thickness and Punch Force in Die Surface Angled Hydro-mechanical Deep Drawing Method
In this study, the effect of die surface angled hydro-mechanical deep drawing method (HMDDM) on sheet metal cup wall thickness and punch force was investigated as experimental and numerical analysis. In the works, 0.9 mm thick DIN EN 10130-1999 sheet metal material was used. The effect of variables on the test results was investigated by using die surface/blank holder angle, punch nose radius, die shoulder radius, chamber pressure and blank holder force as experimental parameters. Numerical analysis experiments were carried out using ANSYS 15.0 package program. Besides, experiments were performed according to the Taguchi experiment plan and L18 orthogonal array. The obtained data were analysed statistically by ANOVA analysis of variance in MINITAB 17.0 package program, and the effect of each parameter on the results was determined as a percentage. As a result, it was determined that the thinning was approximately 15% at most and the thickening was 10%.
- 31 December 2021
- Published by International Journal of Innovative Engineering Applications in International Journal of Innovative Engineering Applications
- Vol. 5 (2) , 181-186
The Effect of Cutting Parameters on White Layer Thickness and Surface Hardness in Wire EDM of Heat-treated D2 Cold Work Tool Steel
Bu çalışmada tel erozyon (WEDM) yöntemi kullanılarak Sverker 21 soğuk iş takım çeliğinin kesme parametrelerinin işleme sonrası malzemede oluşan beyaz tabaka ve kesme yüzeyi sertliğine etkileri incelenmiştir. Yüksek alaşımlı çeliğin kullanılmasındaki amaç; içerdiği alaşım elementi ve karbon oranına bağlı olarak yüksek sertlik, aşınma dayanımı ve tokluk özelliklerinden dolayı kalıpçılık endüstrisinde yaygın olarak kullanılmasıdır. Deneysel çalışmalarda hem ticari hem de ısıl işleme tabi tutulmuş soğuk iş takım çeliği kullanılmıştır. Kesme parametreleri olarak ticari numune ve ısıl işlem görmüş numune, iki ark arası süre (µs), voltaj (V), sıvı basıncı (bar), tel gerginliği (g), tel ilerleme hızı (m/min) kullanılmıştır. Deney tasarımı için Taguchi deney tasarım planı ve L18 ortogonal dizini kullanılarak malzemeler kesilmiştir. Sonuç olarak işlenmiş yüzey sertliği ve yeniden oluşan beyaz tabaka kalınlığı incelenmiştir. ANOVA yöntemine göre beyaz tabaka kalınlığı üzerindeki en etkili parametre % 57.236 ile ticari ve ısıl işlem görmüş numune parametresidir. Kesilen yüzey sertlik değerlerinde ise en etkin parametre % 98.627 oranında numune parametresi olmuştur.
- 31 December 2021
- Published by International Journal of Innovative Engineering Applications in International Journal of Innovative Engineering Applications
- Vol. 5 (2) , 181-186
The Effect of Cutting Parameters on White Layer Thickness and Surface Hardness in Wire EDM of Heat-treated D2 Cold Work Tool Steel
Bu çalışmada tel erozyon (WEDM) yöntemi kullanılarak Sverker 21 soğuk iş takım çeliğinin kesme parametrelerinin işleme sonrası malzemede oluşan beyaz tabaka ve kesme yüzeyi sertliğine etkileri incelenmiştir. Yüksek alaşımlı çeliğin kullanılmasındaki amaç; içerdiği alaşım elementi ve karbon oranına bağlı olarak yüksek sertlik, aşınma dayanımı ve tokluk özelliklerinden dolayı kalıpçılık endüstrisinde yaygın olarak kullanılmasıdır. Deneysel çalışmalarda hem ticari hem de ısıl işleme tabi tutulmuş soğuk iş takım çeliği kullanılmıştır. Kesme parametreleri olarak ticari numune ve ısıl işlem görmüş numune, iki ark arası süre (µs), voltaj (V), sıvı basıncı (bar), tel gerginliği (g), tel ilerleme hızı (m/min) kullanılmıştır. Deney tasarımı için Taguchi deney tasarım planı ve L18 ortogonal dizini kullanılarak malzemeler kesilmiştir. Sonuç olarak işlenmiş yüzey sertliği ve yeniden oluşan beyaz tabaka kalınlığı incelenmiştir. ANOVA yöntemine göre beyaz tabaka kalınlığı üzerindeki en etkili parametre % 57.236 ile ticari ve ısıl işlem görmüş numune parametresidir. Kesilen yüzey sertlik değerlerinde ise en etkin parametre % 98.627 oranında numune parametresi olmuştur.
- 19 May 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (12) , 11783-11795
A New Optimization Technique in Examining the Machinability of Sverker 21 Steel: Gray Relational Analysis-Based Genetic Algorithm
- 19 May 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (12) , 11783-11795
A New Optimization Technique in Examining the Machinability of Sverker 21 Steel: Gray Relational Analysis-Based Genetic Algorithm
- 27 November 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (1-2) , 791-801
The limit drawing ratio in die angled hydromechanical deep drawing method
- 27 November 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (1-2) , 791-801
The limit drawing ratio in die angled hydromechanical deep drawing method