Alexander Solovyov has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Исследование структуры и свойств заготовок из сплава ЭП741НП, полученных методом горячего изостатического прессования

    by Александр Анатольевич Хлыбов, Дмитрий Александрович Рябов, Александр Александрович Соловьев, Анна Алексеевна Шуянова, Алина Александровна Демченко

    Исследованы процессы формирования структуры и свойств заготовок из жаропрочного никелевого сплава ЭП741НП, полученных методом горячего изостатического прессования (ГИП), а также влияние термической обработки (ТО) на его свойства. Установлено, что в заготовке после ГИП присутствуют поры, при этом распределение их объемной доли по сечению неравномерно. Проведен цифровой анализ микроструктуры на периферии и в центре заготовки, определены размер и анизотропия зерна. Выполнена оценка основных механических характеристик сплава ЭП741НП после ГИП и последующей ТО (закалка и трехступенчатое старение) в диапазоне температур 20 – 900 °C. Установлено, что проведение ТО способствует повышению прочностных характеристик сплава ЭП741НП во всем температурном интервале испытаний. Определено изменение твердости, модулей нормальной упругости E и сдвига G по сечению заготовки после ГИП и последующей ТО.

  • Open Access

    Ultrasonic Study of Longitudinal Critically Refracted and Bulk Waves of the Heat-Affected Zone of a Low-Carbon Steel Welded Joint under Fatigue

    by Alexander Gonchar, Alexander Solovyov, Vyacheslav Klyushnikov

    Currently, ultrasonic methods for assessing the fatigue lifetime of various structural materials are being actively developed. Many steel constructions are made by welding. The weld heat-affected zone is the weak point of the construction, as it is most susceptible to destruction. Therefore, it is actually important to search for acoustic parameters that uniquely characterize the structural damage accumulation in the heat-affected zone of a welded joint in order to predict failure. In this work, the specimens were made from the base metal and the welded joint’s heat-affected zone. The specimens were subjected to uniaxial tension–compression under a symmetrical cycle in the region of low-cycle fatigue with control of the strain amplitude. The propagation bulk velocities of longitudinal, shear waves and subsurface longitudinal critically refracted (LCR) waves during cyclic loading were studied. The acoustic birefringence of shear waves was calculated, and a similar parameter was proposed for longitudinal and LCR waves. The dependence of the elastic modulus ratio on the cycle ratio was obtained. It was shown that the acoustic parameters change most intensively in the heat-affected zone. According to the data of the C33/C55 ratio changes measured through the ultrasonic method, a formula for calculating the remaining fatigue life in the heat-affected zone was proposed.


  • Open Access

    The effect of plastic deformation on the structure and properties of 20CRMNSI steel obtained by additive electric arc cultivation

    by Alexander A. Khlybov, Dmitry A. Ryabov, Alexander A. Solovyov, Максим Сергеевич Аносов, Yuri I. Matveev, Александр Анатольевич Хлыбов, Дмитрий Александрович Рябов, Александр Александрович Соловьев

    The paper presents the results of a study of the influence of the degree of deformation under uniaxial tension on the structure and physico-mechanical properties of 20KHGSA steel obtained by 3D printing by electric arc surfacing. It is shown that additive technologies for the production of materials and products have become widespread. In particular, the technologies of electric arc cultivation (WAAM method) are of particular interest. The undoubted advantage of the WAAM method is the relatively low cost of equipment and surfaced material (in comparison with laser or electron beam equipment), as well as the possibility of obtaining large-sized blanks with the least number of defects. A comparative analysis of the influence of the direction of surfacing on the properties of samples during mechanical tests is carried out. It is established that the destruction of the material occurs more intensively in the sample cut perpendicular to the direction of surfacing. Non-destructive methods for estimating the deformed state of 20KHGSA steel under uniaxial tension are proposed. It is shown that one of the most sensitive non-destructive methods for assessing the deformed state of metallic materials is the ultrasonic echo-pulse control method, which is a useful quantitative tool for monitoring the state of the material due to its simplicity and reliability. The magnetic control method has a high sensitivity to deformations. The dependence of the magnetic properties of metals (in particular, the coercive force Hc) on the degree of deformation of the material is shown


  • Open Access

    Microstructure, Phase Composition, and Mechanical Properties of a Layered Bimetallic Composite ER70S-6-ER309LSI Obtained by the WAAM Method

    by Yury Kabaldin, Dmitrii Shatagin, Dmitrii Ryabov, Alexander Solovyov, Andrey Kurkin

    Currently, additive manufacturing technologies for materials and products are being implemented and improved. This is due to the possibility of creating workpieces with complex geometric shapes and specified functional gradient properties. The materials with the most complex functional properties demanded by the military–energy industry include bimetals of the “low-alloyed carbon steel—stainless chromium-nickel steel” type. One of the promising ways to obtain bimetallic products is the WAAM (Wire Arc Additive Manufacturing) technology. Despite the large scientific groundwork, the composition, structure, and properties of bimetallic composites produced by WAAM have not been sufficiently studied. The aim of the current work is to study the effect of WAAM parameters and the subsequent heat treatment on the composition, structure, and physical and mechanical properties of the bimetallic composite “ER70S-6-R309LSI”. Spectral, metallographic, and X-ray diffraction studies were carried out, as were mechanical tests of the samples obtained under various WAAM modes. In order to improve the composites’ properties, various types of heat treatments were applied. It is shown that the WAAM modes, the building strategy, and heat treatment determine the structure of layers and transition zones, as well as the mechanical characteristics of the composite. The structure of ER70S-6 in the composite is represented by the ferrite and the ferrite–cementite mixture (pearlite), and ER309LSI is represented by different ratios of austenite, δ-ferrite, carbide, and intermetallic phases. From the point of view of the mechanical properties, the most promising mode of surfacing is “Double Pulse”, followed by heat treatment by way of austenitization and normalization annealing. In this case, there is a decrease in the content of the δ-ferrite, a leveling of microhardness values, and a 40% increase in the tensile strength of the composite.