Dmitry A. Ryabov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dmitry A. Ryabov has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
A. A. Khlybov
Nizhny Novgorod State Technical University n.a. R. E. Alekseev, Nizhny Novgorod, Russia
4 shared publications- Alexander A. Khlybov
Nizhny Novgorod State Technical University named after R.E. Alekseev, Nizhny Novgorod, Russia
4 shared publications A. A. Shuyanova
Nizhny Novgorod State Technical University (NNSTU), Nizhny Novgorod, Russia
3 shared publications- Alexander Solovyov
Нижегородский государственный технический университет им. Р.Е. Алексеева
2 shared publications - Dmitrii Shatagin
Department of Technology and Equipment of Mechanical Engineering, Nizhny Novgorod State Technical University, 603155 Nizhny Novgorod, Russia
2 shared publications R. E. Alekseev Nizhny Novgorod State Technical University
2 shared publications
Latest Publications
- 1 August 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 62 (8) , 1216-1228
Assessment of Damage and Physico-Mechanical Properties of DMD Samples Made of 12Cr18Ni10Ti Steel under Uniaxial Deformation Conditions
The effect of uniaxial deformation on the damage, structure, and physico-mechanical properties of 12Cr18Ni10Ti steel samples produced by direct metal deposition (DMD) was investigated. Input testing of the powder material was carried out; the granulometric composition and particle shape factor were determined. Samples from the central and outer zones, differing in residual porosity (0.25 and 0.67%, respectively), were cut from the printed blank. Stepwise mechanical tensile tests were performed to evaluate the true flow stress, microhardness, fractal dimension of the microstructure, acoustic parameters, and the volume fraction of the magnetic phase. Anisotropy of mechanical properties across the cross-section of the workpiece was established: the central zone has higher strength but lower plastic characteristics. A linear correlation between microhardness and true flow stress was revealed. It is shown that the fractal dimension of the microstructure decreases monotonically with increasing damage. It was found that the acoustic parameters (\({{D}_{C}}\), acoustic anisotropy (\(A\)), the propagation time of Rayleigh waves) and the volume fraction of the magnetic phase caused by the formation of deformation martensite demonstrate high sensitivity to damage accumulation. The results obtained justify the use of non-destructive acoustic and magnetic testing methods for diagnosing material degradation in 12Cr18Ni10Ti steel products obtained by the DMD method.- 1 August 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 62 (8) , 1216-1228
Assessment of Damage and Physico-Mechanical Properties of DMD Samples Made of 12Cr18Ni10Ti Steel under Uniaxial Deformation Conditions
The effect of uniaxial deformation on the damage, structure, and physico-mechanical properties of 12Cr18Ni10Ti steel samples produced by direct metal deposition (DMD) was investigated. Input testing of the powder material was carried out; the granulometric composition and particle shape factor were determined. Samples from the central and outer zones, differing in residual porosity (0.25 and 0.67%, respectively), were cut from the printed blank. Stepwise mechanical tensile tests were performed to evaluate the true flow stress, microhardness, fractal dimension of the microstructure, acoustic parameters, and the volume fraction of the magnetic phase. Anisotropy of mechanical properties across the cross-section of the workpiece was established: the central zone has higher strength but lower plastic characteristics. A linear correlation between microhardness and true flow stress was revealed. It is shown that the fractal dimension of the microstructure decreases monotonically with increasing damage. It was found that the acoustic parameters (\({{D}_{C}}\), acoustic anisotropy (\(A\)), the propagation time of Rayleigh waves) and the volume fraction of the magnetic phase caused by the formation of deformation martensite demonstrate high sensitivity to damage accumulation. The results obtained justify the use of non-destructive acoustic and magnetic testing methods for diagnosing material degradation in 12Cr18Ni10Ti steel products obtained by the DMD method.- 19 February 2026
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 17 (1) , 184-193
Evaluation of Influence of Technological Parameters of DMD Printing of 12Kh18N10T Alloy Samples on Their Physical and Mechanical Characteristics and Parameters of Nondestructive Testing
This study assessed the influence of the orientation of printed layers (90°, 45°, and 0°) in 12Kh18N10T alloy specimens relative to the direction of uniaxial deformation on the microstructure, physical and mechanical properties, and nondestructive testing parameters. It was found that deformation of specimens results in the intensive formation of structural defects, which significantly impact the strength properties of material (increasing the yield strength and microhardness), as well as the nondestructive testing diagnostic parameters. These results of research can be used to assess the condition of structures made of stainless chromium-nickel steels using the DMD method.
- 19 February 2026
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 17 (1) , 184-193
Evaluation of Influence of Technological Parameters of DMD Printing of 12Kh18N10T Alloy Samples on Their Physical and Mechanical Characteristics and Parameters of Nondestructive Testing
This study assessed the influence of the orientation of printed layers (90°, 45°, and 0°) in 12Kh18N10T alloy specimens relative to the direction of uniaxial deformation on the microstructure, physical and mechanical properties, and nondestructive testing parameters. It was found that deformation of specimens results in the intensive formation of structural defects, which significantly impact the strength properties of material (increasing the yield strength and microhardness), as well as the nondestructive testing diagnostic parameters. These results of research can be used to assess the condition of structures made of stainless chromium-nickel steels using the DMD method.
- 1 May 2025
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2025 (5) , 1288-1294
Effect of Ultrasonic Impact Treatment on the Structure and Properties of the Surface Layer of a 40Cr13 Steel Billet
A 40Cr13 steel billet has been used as an example to assess the effect of indenter load during ultrasonic impact treatment on the microstructure and geometric parameters of the treatment zone and the hardness of the material. The results demonstrate that the optimal indenter load for the 40Cr13 steel billet material is 200 N. The ultrasonic impact treatment conditions chosen lead to considerable changes in the structure (a decrease in the particle size of the carbides and an increase in their volume fraction) and properties (an increase in hardness) of the surface layer of the samples studied.
- 1 May 2025
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2025 (5) , 1288-1294
Effect of Ultrasonic Impact Treatment on the Structure and Properties of the Surface Layer of a 40Cr13 Steel Billet
A 40Cr13 steel billet has been used as an example to assess the effect of indenter load during ultrasonic impact treatment on the microstructure and geometric parameters of the treatment zone and the hardness of the material. The results demonstrate that the optimal indenter load for the 40Cr13 steel billet material is 200 N. The ultrasonic impact treatment conditions chosen lead to considerable changes in the structure (a decrease in the particle size of the carbides and an increase in their volume fraction) and properties (an increase in hardness) of the surface layer of the samples studied.
- 1 May 2025
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 67 (1-2) , 122-129
Study of the Structure and Properties of Billets from Alloy EP741NP Obtained by Hot Isostatic Pressing
- 1 May 2025
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 67 (1-2) , 122-129
Study of the Structure and Properties of Billets from Alloy EP741NP Obtained by Hot Isostatic Pressing
- 1 January 2025
- Published by Science & Technology in Materials Science
- No. 8
Evaluation of influence of technological parameters of dmd printing of 12x18h10t alloy samples on their physical-mechanical characteristics and parameters of non-destructive testing
The influence of the orientation of the printed layers (90, 45 and 0°) in 12X18H10T (12Kh18N10T) alloy samples relative to the direction of uniaxial deformation on the microstructure, physical-mechanical characteristics and parameters of non-destructive testing has been evaluated. It was found that during deformation of the samples, intensive formation of structural defects occurred, which have a significant effect on the strength characteristics of the material (an increase in yield strength and microhardness took place), as well as on the diagnostic parameters of non-destructive testing. The results of the conducted studies can be used to evaluate the state of the material of structures made of stainless chromium-nickel steels by the DMD method.
- 1 January 2025
- Published by Science & Technology in Materials Science
- No. 8
Evaluation of influence of technological parameters of dmd printing of 12x18h10t alloy samples on their physical-mechanical characteristics and parameters of non-destructive testing
The influence of the orientation of the printed layers (90, 45 and 0°) in 12X18H10T (12Kh18N10T) alloy samples relative to the direction of uniaxial deformation on the microstructure, physical-mechanical characteristics and parameters of non-destructive testing has been evaluated. It was found that during deformation of the samples, intensive formation of structural defects occurred, which have a significant effect on the strength characteristics of the material (an increase in yield strength and microhardness took place), as well as on the diagnostic parameters of non-destructive testing. The results of the conducted studies can be used to evaluate the state of the material of structures made of stainless chromium-nickel steels by the DMD method.
- 1 January 2025
- Published by Science & Technology in Technology of Metals
- No. 4
Investigation of impact of ultrasonic shock treatment on structure and properties of surface layer of 40x13 steel billet
Using the example of a 40X13 (Russian name) steel billet, the effect of the downforce during ultrasonic shock treatment on the microstructure, geometric parameters of the treated area and the hardness of the material has been studied. It is shown that for a 40X13 steel billet material, the optimal downforce value is 200 N. The chosen mode of shock ultrasonic treatment leads to a significant change in the structure (reduction in size and increase in the volume fraction of carbides) and properties (increase in hardness) of the surface layers of the studied samples.
- 1 January 2025
- Published by Science & Technology in Technology of Metals
- No. 4
Investigation of impact of ultrasonic shock treatment on structure and properties of surface layer of 40x13 steel billet
Using the example of a 40X13 (Russian name) steel billet, the effect of the downforce during ultrasonic shock treatment on the microstructure, geometric parameters of the treated area and the hardness of the material has been studied. It is shown that for a 40X13 steel billet material, the optimal downforce value is 200 N. The chosen mode of shock ultrasonic treatment leads to a significant change in the structure (reduction in size and increase in the volume fraction of carbides) and properties (increase in hardness) of the surface layers of the studied samples.
- 26 August 2024
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 8,p. 32-38
Influence of WAAM process parameters on the composition and structure of the Sv-08G2S – Sv-07Kh25N13 layered bimetallic composite
Currently, more and more attention is being paid to additive technologies from the side of real production. This is due to the unique capabilities to create complex, large-sized blanks with functional gradient properties. Particular attention is paid to the creation of products made of layered composite bimetallic materials. The most popular materials systems include bimetals of the “low–alloy carbon steel - stainless chromium-nickel steel” type, which are widely used in the energy, military and aerospace industries. One of the ways to produce such products is the technology of electric arc cultivation (Wire Arc Additive Manufacturing – WAAM). However, despite the great scientific groundwork, the composition, structure and properties of bimetallic composites produced by the WAAM method have not been sufficiently studied. The purpose of the presented work is to study the effect of WAAM technological parameters on the composition and structure of the layered bimetallic composite “Sv-08G2S – Sv-07Kh25N13”. Experimental samples for research were produced by the WAAM method at various printing strategies and specific energies. Studies of the microstructure of the sections and chemical analysis of various zones of the composite were carried out. It is shown that the WAAM modes and the surfacing strategy largely determine the structure and phase composition of the main layers and transition zones of the bimetallic composite. The structure of Sv-08G2S steel in the composite is represented by ferrite and ferrite-cementite mixture (perlite), and Sv-07Kh25N13 steel by various ratios of austenite, δ-ferrite, carbides and intermetallide phases. It has been established that the distribution of chemical elements in various sections of the steel Sv-08G2S included in the bimetallic composite is stable and does not depend on the parameters of WAAM surfacing for steel Sv-07Kh25N13. For steel Sv-07Kh25N13, the distribution of chemical elements significantly depends on the WAAM surfacing mode.The work was supported by the grant of the Russian Science Foundation No. 22-79-10204 “Development of scientific and technological foundations for the synthesis of WAAM-obtained layered polymetallic composite materials for operation in low-temperature conditions.”
- 26 August 2024
- Published by Ore and Metals Publishing House in Chernye Metally
- No. 8,p. 32-38
Influence of WAAM process parameters on the composition and structure of the Sv-08G2S – Sv-07Kh25N13 layered bimetallic composite
Currently, more and more attention is being paid to additive technologies from the side of real production. This is due to the unique capabilities to create complex, large-sized blanks with functional gradient properties. Particular attention is paid to the creation of products made of layered composite bimetallic materials. The most popular materials systems include bimetals of the “low–alloy carbon steel - stainless chromium-nickel steel” type, which are widely used in the energy, military and aerospace industries. One of the ways to produce such products is the technology of electric arc cultivation (Wire Arc Additive Manufacturing – WAAM). However, despite the great scientific groundwork, the composition, structure and properties of bimetallic composites produced by the WAAM method have not been sufficiently studied. The purpose of the presented work is to study the effect of WAAM technological parameters on the composition and structure of the layered bimetallic composite “Sv-08G2S – Sv-07Kh25N13”. Experimental samples for research were produced by the WAAM method at various printing strategies and specific energies. Studies of the microstructure of the sections and chemical analysis of various zones of the composite were carried out. It is shown that the WAAM modes and the surfacing strategy largely determine the structure and phase composition of the main layers and transition zones of the bimetallic composite. The structure of Sv-08G2S steel in the composite is represented by ferrite and ferrite-cementite mixture (perlite), and Sv-07Kh25N13 steel by various ratios of austenite, δ-ferrite, carbides and intermetallide phases. It has been established that the distribution of chemical elements in various sections of the steel Sv-08G2S included in the bimetallic composite is stable and does not depend on the parameters of WAAM surfacing for steel Sv-07Kh25N13. For steel Sv-07Kh25N13, the distribution of chemical elements significantly depends on the WAAM surfacing mode.The work was supported by the grant of the Russian Science Foundation No. 22-79-10204 “Development of scientific and technological foundations for the synthesis of WAAM-obtained layered polymetallic composite materials for operation in low-temperature conditions.”
- 1 August 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 60 (8) , 843-858
Developing a Method for Assessing the Degree of Hydrogenation of VT1-0 Titanium Alloy by the Acoustic Method
The possibilities of using a nondestructive acoustic method to determine the degree of hydrogenation of VT1-0 titanium alloy are investigated. The features of using various acoustic parameters to construct computational and experimental methods for determining the porosity of titanium alloy at various stages of its hydrogenation are analyzed. The sources of errors of the proposed methods, the limits of their applicability, as well as the requirements for hardware and software for their implementation are considered. The results of acoustic measurements carried out on samples made of VT1-0 alloy are compared with the ideas about the patterns of its structural changes during hydrogenation process. The possibility is shown for creating engineering algorithms based on the obtained experimental data for assessing the state of the product material subjected to hydrogenation in order to prevent dangerous degradation of its operational properties.
- 1 August 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 60 (8) , 843-858
Developing a Method for Assessing the Degree of Hydrogenation of VT1-0 Titanium Alloy by the Acoustic Method
The possibilities of using a nondestructive acoustic method to determine the degree of hydrogenation of VT1-0 titanium alloy are investigated. The features of using various acoustic parameters to construct computational and experimental methods for determining the porosity of titanium alloy at various stages of its hydrogenation are analyzed. The sources of errors of the proposed methods, the limits of their applicability, as well as the requirements for hardware and software for their implementation are considered. The results of acoustic measurements carried out on samples made of VT1-0 alloy are compared with the ideas about the patterns of its structural changes during hydrogenation process. The possibility is shown for creating engineering algorithms based on the obtained experimental data for assessing the state of the product material subjected to hydrogenation in order to prevent dangerous degradation of its operational properties.
- Open Access
- 19 June 2023
- Published by Volga State University of Water Transport in Russian Journal of Water Transport
- No. 75,p. 95-107
The effect of plastic deformation on the structure and properties of 20CRMNSI steel obtained by additive electric arc cultivation
The paper presents the results of a study of the influence of the degree of deformation under uniaxial tension on the structure and physico-mechanical properties of 20KHGSA steel obtained by 3D printing by electric arc surfacing. It is shown that additive technologies for the production of materials and products have become widespread. In particular, the technologies of electric arc cultivation (WAAM method) are of particular interest. The undoubted advantage of the WAAM method is the relatively low cost of equipment and surfaced material (in comparison with laser or electron beam equipment), as well as the possibility of obtaining large-sized blanks with the least number of defects. A comparative analysis of the influence of the direction of surfacing on the properties of samples during mechanical tests is carried out. It is established that the destruction of the material occurs more intensively in the sample cut perpendicular to the direction of surfacing. Non-destructive methods for estimating the deformed state of 20KHGSA steel under uniaxial tension are proposed. It is shown that one of the most sensitive non-destructive methods for assessing the deformed state of metallic materials is the ultrasonic echo-pulse control method, which is a useful quantitative tool for monitoring the state of the material due to its simplicity and reliability. The magnetic control method has a high sensitivity to deformations. The dependence of the magnetic properties of metals (in particular, the coercive force Hc) on the degree of deformation of the material is shown
- 19 June 2023
- Published by Volga State University of Water Transport in Russian Journal of Water Transport
- No. 75,p. 95-107
Open AccessThe effect of plastic deformation on the structure and properties of 20CRMNSI steel obtained by additive electric arc cultivation
The paper presents the results of a study of the influence of the degree of deformation under uniaxial tension on the structure and physico-mechanical properties of 20KHGSA steel obtained by 3D printing by electric arc surfacing. It is shown that additive technologies for the production of materials and products have become widespread. In particular, the technologies of electric arc cultivation (WAAM method) are of particular interest. The undoubted advantage of the WAAM method is the relatively low cost of equipment and surfaced material (in comparison with laser or electron beam equipment), as well as the possibility of obtaining large-sized blanks with the least number of defects. A comparative analysis of the influence of the direction of surfacing on the properties of samples during mechanical tests is carried out. It is established that the destruction of the material occurs more intensively in the sample cut perpendicular to the direction of surfacing. Non-destructive methods for estimating the deformed state of 20KHGSA steel under uniaxial tension are proposed. It is shown that one of the most sensitive non-destructive methods for assessing the deformed state of metallic materials is the ultrasonic echo-pulse control method, which is a useful quantitative tool for monitoring the state of the material due to its simplicity and reliability. The magnetic control method has a high sensitivity to deformations. The dependence of the magnetic properties of metals (in particular, the coercive force Hc) on the degree of deformation of the material is shown