Eyüp Sabri Kayali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Eyüp Sabri Kayali has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Faik Nuzhet Oktar
Center for Nanotechnology & Biomaterials Applications and Research (NBUAM), Marmara University, Istanbul, Turkey
2 shared publications - Simeon Agathopoulos
Department of Materials Science and Engineering University of Ioannina Ioannina Greece
2 shared publications - Bahar Sennaroglu
Department of Industrial Engineering, Marmara University, Istanbul, Turkey
1 shared publication - Dilshat U. Tulyaganov
Department of Natural-Mathematical Sciences, Turin Polytechnic University in Tashkent, 17, Small Ring Street, Tashkent 100095, Uzbekistan
1 shared publication - Fatma Sibel Salman
Koc University
1 shared publication G. Rocha
University of Aveiro
1 shared publication
Latest Publications
- 1 October 2019
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 23 (5) , 972-981
Effect of Reduction Ratio below Austenite Recrystallization Stop Temperature on Mechanical Properties of an API X70M PSL2 Line Pipe Steel
Steel grades having high toughness and high strength are required for line pipes since gas and oil should be transported through them at high pressures. Thermo-mechanically controlled rolling processes are used for increasing both toughness and strength at low temperatures since the line pipes are exposed to harsh climatic conditions at full length and rather severe service conditions. Various test methods such as Charpy, DWTT, CTOA have been used for measurement of toughness values of these steels and the results have been evaluated considering various criteria. In this study, thermo-mechanical rolling trials were performed at the temperature below the recrystallization temperature of austenite on an API X70M PSL2 grade steel, which is large scale used in the oil and natural gas line pipes, to increase the strength without sacrificing the toughness. Different reduction ratios were utilized and the effect of reduction ratios on mechanical properties and microstructures were investigated during the trials. It was observed that final grain size decreased and strength and toughness increased with increasing reduction ratio.
- 1 October 2019
- Published by Sakarya University Journal of Science in Sakarya University Journal of Science
- Vol. 23 (5) , 972-981
Effect of Reduction Ratio below Austenite Recrystallization Stop Temperature on Mechanical Properties of an API X70M PSL2 Line Pipe Steel
Steel grades having high toughness and high strength are required for line pipes since gas and oil should be transported through them at high pressures. Thermo-mechanically controlled rolling processes are used for increasing both toughness and strength at low temperatures since the line pipes are exposed to harsh climatic conditions at full length and rather severe service conditions. Various test methods such as Charpy, DWTT, CTOA have been used for measurement of toughness values of these steels and the results have been evaluated considering various criteria. In this study, thermo-mechanical rolling trials were performed at the temperature below the recrystallization temperature of austenite on an API X70M PSL2 grade steel, which is large scale used in the oil and natural gas line pipes, to increase the strength without sacrificing the toughness. Different reduction ratios were utilized and the effect of reduction ratios on mechanical properties and microstructures were investigated during the trials. It was observed that final grain size decreased and strength and toughness increased with increasing reduction ratio.
- 1 May 2006
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 309-311, 101-104
Sintering Effect on Mechanical Properties of Composites of Hydroxyapatite Lanthanum Oxide (HA-La2O3)
Composites of calcinated bovine bone derived hydroxyapatite (HA) with 0.25, 0.5, 1, and 2 wt % La2O3 were prepared by sintering. The experimental results indicated that compression strength and microhardness of HA-La2O3 composites increase when the content of La2O3 and sintering temperature increase. The best mechanical properties were achieved after sintering at 1300°C. The results are in agreement with densification measurements and microstructure analysis.
- 1 May 2006
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 309-311, 101-104
Sintering Effect on Mechanical Properties of Composites of Hydroxyapatite Lanthanum Oxide (HA-La2O3)
Composites of calcinated bovine bone derived hydroxyapatite (HA) with 0.25, 0.5, 1, and 2 wt % La2O3 were prepared by sintering. The experimental results indicated that compression strength and microhardness of HA-La2O3 composites increase when the content of La2O3 and sintering temperature increase. The best mechanical properties were achieved after sintering at 1300°C. The results are in agreement with densification measurements and microstructure analysis.
- 15 April 2005
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 284-286, 709-712
The Influence of Sintering Temperature on the Properties of Composites of Biologic Hydroxyapatite and Zirconia
Bovine derived hydroxyapatite was doped with partially stabilized zirconia with 3 mol% yttria. The influence of sintering temperature and the amount of the incorporated zirconia on densification, mechanical properties, crystalline structure and microstructure was investigated. The results indicate that the produced materials exhibit poorer mechanical properties than the relevant composite materials of enamel derived hydroxyapatite. This difference can be attributed to F, since F-content in bone is much higher than in enamel. Hence, in the light of the prospective use of the investigated materials in biomedicine, bovine derived hydroxyapatite doped with zirconia can potentially serve as graft material for load bearing applications if very small amount of F can be incorporated, in order to resemble the composition of enamel derived apatite.
- 15 April 2005
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 284-286, 709-712
The Influence of Sintering Temperature on the Properties of Composites of Biologic Hydroxyapatite and Zirconia
Bovine derived hydroxyapatite was doped with partially stabilized zirconia with 3 mol% yttria. The influence of sintering temperature and the amount of the incorporated zirconia on densification, mechanical properties, crystalline structure and microstructure was investigated. The results indicate that the produced materials exhibit poorer mechanical properties than the relevant composite materials of enamel derived hydroxyapatite. This difference can be attributed to F, since F-content in bone is much higher than in enamel. Hence, in the light of the prospective use of the investigated materials in biomedicine, bovine derived hydroxyapatite doped with zirconia can potentially serve as graft material for load bearing applications if very small amount of F can be incorporated, in order to resemble the composition of enamel derived apatite.