Paramita Bhattacharyya
Paramita Bhattacharyya has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Brahim Ahammou
Institut National de la Recherche Scientdifique, Centre Énergie Matériaux et Télécommunications, Université du Québec 2 , Varennes, Québec J3X 1P7
3 shared publications - Fahmida Azmi
Department of Engineering Physics and Centre for Emerging Device Technologies, McMaster University, Hamilton, Ontario L8S 4L7, Canada
3 shared publications - Peter Mascher
McMaster University
3 shared publications - Rafael N. Kleiman
Department of Engineering Physics, McMaster University, Hamilton, Canada
2 shared publications - Christophe Levallois
Univ Rennes, INSA Rennes, CNRS, Institut FOTON – UMR 6082, F-35000 Rennes, France
1 shared publication - Clarissa White
Department of Engineering Physics and Centre for Emerging Device Technologies (CEDT), McMaster University 1 , Hamilton, Ontario L8S 4L7
1 shared publication
Latest Publications
- 5 December 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (1)
Design method for generating multiple colors with thickness-modulated thin-film optical filters for silicon solar cells
This study explores an innovative approach to enhance the esthetic appeal while having minimal impact on the functional performance of solar-charged electric vehicles. We propose replacing the standard antireflective coating on solar cells with a custom-designed notch filter. This optical filter ensures high transmission across the solar spectrum and creates a distinct color rendering effect in the visible range, thereby making the cells more visually appealing. We utilized niobium pentoxide and silicon dioxide for their excellent optical, mechanical, and corrosive properties to fabricate filters reflecting at specific wavelengths, producing vibrant blue, green, and red color renderings at 400, 550, and 632 nm, respectively. Theoretical relative photocurrent density losses of only ∼7%,∼10%, and ∼14% were observed for blue, green, and red colors, respectively, due to the presence of these filters when compared to a silicon solar cell with a standard antireflective coating. Using optilayer and matlab software, we precisely designed filters with just two to four layers, achieving simplicity and effectiveness. Gradual evolution optimization followed by thin layer removal optimization produced automated and consistent thickness-modulated multilayered optical filter designs over a wide range of user inputs. Our designs were fabricated using magnetron sputtering and validated through variable angle spectroscopic ellipsometry and reflectance spectroscopy, showing strong agreement with our simulations. With a minimal trade-off in the functionality and efficiency of solar cells, this method transforms standard solar cells into esthetically pleasing components, broadening their appeal and potential applications in consumer products.
- 5 December 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (1)
Design method for generating multiple colors with thickness-modulated thin-film optical filters for silicon solar cells
This study explores an innovative approach to enhance the esthetic appeal while having minimal impact on the functional performance of solar-charged electric vehicles. We propose replacing the standard antireflective coating on solar cells with a custom-designed notch filter. This optical filter ensures high transmission across the solar spectrum and creates a distinct color rendering effect in the visible range, thereby making the cells more visually appealing. We utilized niobium pentoxide and silicon dioxide for their excellent optical, mechanical, and corrosive properties to fabricate filters reflecting at specific wavelengths, producing vibrant blue, green, and red color renderings at 400, 550, and 632 nm, respectively. Theoretical relative photocurrent density losses of only ∼7%,∼10%, and ∼14% were observed for blue, green, and red colors, respectively, due to the presence of these filters when compared to a silicon solar cell with a standard antireflective coating. Using optilayer and matlab software, we precisely designed filters with just two to four layers, achieving simplicity and effectiveness. Gradual evolution optimization followed by thin layer removal optimization produced automated and consistent thickness-modulated multilayered optical filter designs over a wide range of user inputs. Our designs were fabricated using magnetron sputtering and validated through variable angle spectroscopic ellipsometry and reflectance spectroscopy, showing strong agreement with our simulations. With a minimal trade-off in the functionality and efficiency of solar cells, this method transforms standard solar cells into esthetically pleasing components, broadening their appeal and potential applications in consumer products.
- Open Access
- 23 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Mechanical and optical properties of amorphous silicon nitride-based films prepared by electron cyclotron resonance plasma-enhanced chemical vapor deposition
Silicon nitride (SiNx) based films have been recognized as essential dielectric films in the microelectronics and optoelectronics industry due to their desirable properties, such as high electrical insulation, excellent thermal stability, and compatibility with integrated circuit fabrication processes. They are also a potential candidate for fabricating wavelength-selective reflective coatings and surface passivation layers in building-integrated photovoltaics technologies. SiNx-based films are one of the popular choices for antireflective coatings in photovoltaics as well. Recently, SiNx and oxynitride (SiOyNx) based thin film optical filters have been explored to provide distinct color rendering to solar-charged electrical vehicles. Since solar cells have a lifespan of many years and the coating surfaces are substantial, it is essential to produce films with controlled optical and mechanical properties and maintain mechanical integrity against corrosion and wear. This study aims to design a deposition process and optimize minimal parameters for stable plasma conditions during multilayer deposition of SiNx and SiOyNx films using an electron cyclotron resonance plasma-enhanced chemical vapor deposition reactor with SiH4/N2/O2/Ar precursor mixtures at 120 °C. The primary goal was to investigate the influence of gas flow adjustments on the optical and mechanical properties, specifically targeting the refractive index and mechanical properties of the films. We measured the refractive index and the absorption of the films using variable angle spectroscopic ellipsometry. Then, we evaluated the mechanical residual stress ex situ using the wafer curvature measurement method. We have determined the elastic modulus and the hardness of the films using nanoindentation. The experimental results have shown a significant dependence of the optical and mechanical properties on the deposition parameters. To investigate the factors contributing to the intrinsic mechanical stress and to better understand SiNx film degradation mechanisms, we have studied the effect of postdeposition thermal cycling on the properties of the films. Several thermal-cycling experiments from room temperature to 400 °C were performed on different SiNx films, and the results showed an irreversible variation of the mechanical stress toward the tensile stresses caused by delamination of the films, while the refractive index remained unchanged.
- 23 August 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (5)
Open AccessMechanical and optical properties of amorphous silicon nitride-based films prepared by electron cyclotron resonance plasma-enhanced chemical vapor deposition
Silicon nitride (SiNx) based films have been recognized as essential dielectric films in the microelectronics and optoelectronics industry due to their desirable properties, such as high electrical insulation, excellent thermal stability, and compatibility with integrated circuit fabrication processes. They are also a potential candidate for fabricating wavelength-selective reflective coatings and surface passivation layers in building-integrated photovoltaics technologies. SiNx-based films are one of the popular choices for antireflective coatings in photovoltaics as well. Recently, SiNx and oxynitride (SiOyNx) based thin film optical filters have been explored to provide distinct color rendering to solar-charged electrical vehicles. Since solar cells have a lifespan of many years and the coating surfaces are substantial, it is essential to produce films with controlled optical and mechanical properties and maintain mechanical integrity against corrosion and wear. This study aims to design a deposition process and optimize minimal parameters for stable plasma conditions during multilayer deposition of SiNx and SiOyNx films using an electron cyclotron resonance plasma-enhanced chemical vapor deposition reactor with SiH4/N2/O2/Ar precursor mixtures at 120 °C. The primary goal was to investigate the influence of gas flow adjustments on the optical and mechanical properties, specifically targeting the refractive index and mechanical properties of the films. We measured the refractive index and the absorption of the films using variable angle spectroscopic ellipsometry. Then, we evaluated the mechanical residual stress ex situ using the wafer curvature measurement method. We have determined the elastic modulus and the hardness of the films using nanoindentation. The experimental results have shown a significant dependence of the optical and mechanical properties on the deposition parameters. To investigate the factors contributing to the intrinsic mechanical stress and to better understand SiNx film degradation mechanisms, we have studied the effect of postdeposition thermal cycling on the properties of the films. Several thermal-cycling experiments from room temperature to 400 °C were performed on different SiNx films, and the results showed an irreversible variation of the mechanical stress toward the tensile stresses caused by delamination of the films, while the refractive index remained unchanged.
- Open Access
- 1 May 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (3)
Design and fabrication of color-generating nitride based thin-film optical filters for photovoltaic applications
In this paper, we present the design and fabrication of a 11-layer notch filter for photovoltaic applications. Thickness modulation has been done on a starting quarter-wave design to obtain a 11-layer final structure. For our design parameters, we considered materials with indices of 2.09 and 1.51 as high and low refractive index materials, respectively. Since this filter aims for photovoltaic applications, we defined the substrate as silicon. The design shows a reflection peak of around 73% from 350 to 467 nm with a FWHM of 79 nm along with less than 10% reflection for longer wavelengths of the remaining high transmission region of 300–1200 nm. For fabrication, we used silicon nitride and silicon oxynitride as alternating high and low refractive index materials on a silicon substrate. Layers of silicon nitride and oxynitride were deposited with an electron cyclotron resonance plasma-enhanced chemical vapor deposition reactor and characterized with variable angle spectroscopic ellipsometry and spectrophotometry.
- 1 May 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (3)
Open AccessDesign and fabrication of color-generating nitride based thin-film optical filters for photovoltaic applications
In this paper, we present the design and fabrication of a 11-layer notch filter for photovoltaic applications. Thickness modulation has been done on a starting quarter-wave design to obtain a 11-layer final structure. For our design parameters, we considered materials with indices of 2.09 and 1.51 as high and low refractive index materials, respectively. Since this filter aims for photovoltaic applications, we defined the substrate as silicon. The design shows a reflection peak of around 73% from 350 to 467 nm with a FWHM of 79 nm along with less than 10% reflection for longer wavelengths of the remaining high transmission region of 300–1200 nm. For fabrication, we used silicon nitride and silicon oxynitride as alternating high and low refractive index materials on a silicon substrate. Layers of silicon nitride and oxynitride were deposited with an electron cyclotron resonance plasma-enhanced chemical vapor deposition reactor and characterized with variable angle spectroscopic ellipsometry and spectrophotometry.