Dmitry Sotnikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dmitry Sotnikov has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Tiina Salmi
Tampere University
5 shared publications - Bernhard Auchmann
Paul Scherrer Institute, Villigen, Switzerland
4 shared publications - Douglas Martins Araujo
Paul Scherrer Institute, Villigen, Switzerland
4 shared publications - Mika Lyly
Quanscient Oy, Tampere, Finland
3 shared publications - Amalia Ballarino
European Organization for Nuclear Research, Geneva, Switzerland
2 shared publications - André Brem
Paul Scherrer Institut, Villigen, Switzerland
2 shared publications
Latest Publications
- Open Access
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
AC Loss Measurement and Validation of an HTS Soldered Stack Cable for Accelerator Magnets
This work explores the use of a double-pancake coil for validating electromagnetic numerical models of HTS cables. We present a cost-effective and rapid production method using 3D-printed plastic formers. High-temperature superconducting (HTS) REBCO tapes are a promising solution for high-field magnets, particularly in accelerator applications, due to their ability to maintain superconducting properties in high magnetic field and high critical current density. One of the most effective ways to utilize HTS tapes is through straight soldered stack cables, which offer excellent packing efficiency in racetrack coil geometries-ideal for Block and Common-coil dipole magnet configurations. Measurements were performed in self-field conditions in liquid nitrogen, with AC current applied at frequencies up to 20 Hz. The current was increased in steps of 5 A of peak current, reaching a maximal of 100 A-below the critical current of the tested samples. For each frequency, the AC loss dependence on peak current showed a smooth trend, while AC losses per cycle remained independent of frequency. The validation process involved finite element method (FEM) modeling, using Jc(B) interpolation from experimental data, ensuring high accuracy. Both single REBCO tapes and soldered face-to-face cables were analyzed and compared to models of different modelling depth. The computational model matched the measured results with an accuracy within 10%. These findings provide a foundation for further research on the practical application of HTS straight soldered stack cables in high-field accelerator magnets.
- 6 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open AccessAC Loss Measurement and Validation of an HTS Soldered Stack Cable for Accelerator Magnets
This work explores the use of a double-pancake coil for validating electromagnetic numerical models of HTS cables. We present a cost-effective and rapid production method using 3D-printed plastic formers. High-temperature superconducting (HTS) REBCO tapes are a promising solution for high-field magnets, particularly in accelerator applications, due to their ability to maintain superconducting properties in high magnetic field and high critical current density. One of the most effective ways to utilize HTS tapes is through straight soldered stack cables, which offer excellent packing efficiency in racetrack coil geometries-ideal for Block and Common-coil dipole magnet configurations. Measurements were performed in self-field conditions in liquid nitrogen, with AC current applied at frequencies up to 20 Hz. The current was increased in steps of 5 A of peak current, reaching a maximal of 100 A-below the critical current of the tested samples. For each frequency, the AC loss dependence on peak current showed a smooth trend, while AC losses per cycle remained independent of frequency. The validation process involved finite element method (FEM) modeling, using Jc(B) interpolation from experimental data, ensuring high accuracy. Both single REBCO tapes and soldered face-to-face cables were analyzed and compared to models of different modelling depth. The computational model matched the measured results with an accuracy within 10%. These findings provide a foundation for further research on the practical application of HTS straight soldered stack cables in high-field accelerator magnets.
- 2 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Partial Homogenization Methods to Simulate HTS Tapes Using the H and T-A Formulations
REBCO coated conductor tapes are a promising technology for developing high-field accelerator magnets since their increased current carrying capacity and operational temperature allows achieving higher-fields and current levels with higher thermal margin. Superconducting materials still present challenges associated with their non-negligible losses in transient conditions, hence, finite element analyses become essential to design feasible superconducting systems. The H formulation is known in literature for its accuracy, while the T-A formulation offers computational efficiency. Nonetheless, both methods remain computationally demanding, especially when the superconducting tapes are modelled considering the extreme aspect ratios of different materials in the layered tapes. Homogenized models have been proposed to reduce computational requirements, however, modelling all layers as a single domain can impose the current to flow through all conducting layers rather than only the REBCO layer, even when its resistivity is very low. This study presents a comparative analysis using the H and the T-A formulations for a partially homogenized model, where the superconducting layer is modelled independently from the remaining conducting layers, and a fully homogenized model. The models' accuracy for transport loss estimation in transient conditions is discussed and compared with experimental loss measurements for a REBCO tape powered with AC currents.
- 2 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Partial Homogenization Methods to Simulate HTS Tapes Using the H and T-A Formulations
REBCO coated conductor tapes are a promising technology for developing high-field accelerator magnets since their increased current carrying capacity and operational temperature allows achieving higher-fields and current levels with higher thermal margin. Superconducting materials still present challenges associated with their non-negligible losses in transient conditions, hence, finite element analyses become essential to design feasible superconducting systems. The H formulation is known in literature for its accuracy, while the T-A formulation offers computational efficiency. Nonetheless, both methods remain computationally demanding, especially when the superconducting tapes are modelled considering the extreme aspect ratios of different materials in the layered tapes. Homogenized models have been proposed to reduce computational requirements, however, modelling all layers as a single domain can impose the current to flow through all conducting layers rather than only the REBCO layer, even when its resistivity is very low. This study presents a comparative analysis using the H and the T-A formulations for a partially homogenized model, where the superconducting layer is modelled independently from the remaining conducting layers, and a fully homogenized model. The models' accuracy for transport loss estimation in transient conditions is discussed and compared with experimental loss measurements for a REBCO tape powered with AC currents.
- Open Access
- 29 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Application of HTS Straight Soldered Stack Cable in Subscale Magnet Geometry
High-temperature superconducting (HTS) cables of fer a promising opportunity for high-field magnet applications. However, the exact technology stack that would lead to accelerator-quality magnets is as yet not consolidated. A vigorous design-build-test cycle is required to evaluate the potential of different approaches. To implement such program at PSI, in the framework of the CHART initiative, we propose using the same magnet geometry previously tested with an LTS stress-managed magnet while replacing the rectangular Nb3Sn Rutherford cables with HTS straight soldered stack cables– a design that seamlessly integrates into the existing structure. Currently, we are in the design and process-development stage, with testing planned for later in 2025. This study presents magnetic field-quality estimation and AC loss computations for the HTS common coils magnet, based on finite element method (FEM) modeling of the final magnet design. The study includes an estimation of the required stabilizer content for protection with dump resistor at a maximum applied current of 10 kA, as well as the design of internal and external joints. Additionally, a novel coil winding technique enables simultaneous winding, insulation, and soldering of the cable, thus, overcoming the tape-stack cable's low minimal bending radius and offering scalability for larger magnet applications. This work represents a possible way for the practical application of HTS cables in accelerator magnets. A direct benchmark against LTS cables in identical geometry provides valuable insights and a faster path-way to experimental results and model validation.
- 29 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
Open AccessApplication of HTS Straight Soldered Stack Cable in Subscale Magnet Geometry
High-temperature superconducting (HTS) cables of fer a promising opportunity for high-field magnet applications. However, the exact technology stack that would lead to accelerator-quality magnets is as yet not consolidated. A vigorous design-build-test cycle is required to evaluate the potential of different approaches. To implement such program at PSI, in the framework of the CHART initiative, we propose using the same magnet geometry previously tested with an LTS stress-managed magnet while replacing the rectangular Nb3Sn Rutherford cables with HTS straight soldered stack cables– a design that seamlessly integrates into the existing structure. Currently, we are in the design and process-development stage, with testing planned for later in 2025. This study presents magnetic field-quality estimation and AC loss computations for the HTS common coils magnet, based on finite element method (FEM) modeling of the final magnet design. The study includes an estimation of the required stabilizer content for protection with dump resistor at a maximum applied current of 10 kA, as well as the design of internal and external joints. Additionally, a novel coil winding technique enables simultaneous winding, insulation, and soldering of the cable, thus, overcoming the tape-stack cable's low minimal bending radius and offering scalability for larger magnet applications. This work represents a possible way for the practical application of HTS cables in accelerator magnets. A direct benchmark against LTS cables in identical geometry provides valuable insights and a faster path-way to experimental results and model validation.
- Open Access
- 30 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Minimizing Conductor Consumption in High-Field HTS Solenoid Design Using Adaptive ANN-Based Optimization Algorithm
Minimizing conductor cost is one of the goals in high-field HTS magnet design. Optimization of magnet design to minimize conductor length is one way to approach the problem. HTS tapes have anisotropic material properties and non-uniform current density within the tape width during operation, which must be accounted in modeling HTS tapes. Finite element method (FEM) based simulations can be used to obtain accurate magnetic field distribution and critical current in an HTS magnet, but these simulations are typically time consuming. For example, a detailed simulation for a 2 T HTS solenoid may take several hours. As a result, it is not efficient to implement the traditional optimization algorithms, which directly use the simulation results to obtain the response of the cost function. To overcome this challenge, a novel optimization algorithm was developed by the authors, namely L-ANN-GWO to reduce the time cost of optimization (L stands for LASSO, ANN stands for artificial neural network, and GWO stands for grey wolf optimizer). In this approach, ANN is trained by FEA set of HTS solenoid designs to approximate the time-consuming simulations of magnetic field distribution based on solenoid geometry. Instead of using the approximation model in a static way, ANN is first trained with a small number of samples and updated adaptively in L-ANN-GWO along with the optimization process. In this contribution, we present application of the L-ANN-GWO optimization algorithm to ReBCO solenoid coils to optimize magnet design to minimize conductor use. The design constraints come from field homogeneity and critical surface. We demonstrate that as a multi-objective optimization, L-ANN-GWO can output the minimized superconductor consumption in different peak magnetic fields from a single optimization run. Future developments foresee adding quench protection requirements into the design optimization as this is another aspect potentially impacting the conductor use.
- 30 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Open AccessMinimizing Conductor Consumption in High-Field HTS Solenoid Design Using Adaptive ANN-Based Optimization Algorithm
Minimizing conductor cost is one of the goals in high-field HTS magnet design. Optimization of magnet design to minimize conductor length is one way to approach the problem. HTS tapes have anisotropic material properties and non-uniform current density within the tape width during operation, which must be accounted in modeling HTS tapes. Finite element method (FEM) based simulations can be used to obtain accurate magnetic field distribution and critical current in an HTS magnet, but these simulations are typically time consuming. For example, a detailed simulation for a 2 T HTS solenoid may take several hours. As a result, it is not efficient to implement the traditional optimization algorithms, which directly use the simulation results to obtain the response of the cost function. To overcome this challenge, a novel optimization algorithm was developed by the authors, namely L-ANN-GWO to reduce the time cost of optimization (L stands for LASSO, ANN stands for artificial neural network, and GWO stands for grey wolf optimizer). In this approach, ANN is trained by FEA set of HTS solenoid designs to approximate the time-consuming simulations of magnetic field distribution based on solenoid geometry. Instead of using the approximation model in a static way, ANN is first trained with a small number of samples and updated adaptively in L-ANN-GWO along with the optimization process. In this contribution, we present application of the L-ANN-GWO optimization algorithm to ReBCO solenoid coils to optimize magnet design to minimize conductor use. The design constraints come from field homogeneity and critical surface. We demonstrate that as a multi-objective optimization, L-ANN-GWO can output the minimized superconductor consumption in different peak magnetic fields from a single optimization run. Future developments foresee adding quench protection requirements into the design optimization as this is another aspect potentially impacting the conductor use.
- 5 November 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (12) , 125006
Electromagnetic-thermal modeling of high-temperature superconducting coils with homogenized method and different formulations: a benchmark
High-temperature superconducting coils are used in various large-scale applications, like rotating machines and high-field magnets. However, modeling these coils is a complicated and time-consuming process, especially due to the non-linearity of the current–voltage characteristics of the superconductors and the complex multiphysics involved. In this work, we used a fast homogenized method to model the coupled electromagnetic and electrothermal properties of racetrack and pancake coils for different applications. For this purpose, various formulations wielding homogenization methods are used and benchmarked with each other, as well as with models considering the detailed structure of the HTS tapes. We observe a very good agreement between different models (homogenized and detailed), and we discuss the pros and cons of the inclusion of insulating layers between the turns in homogenization. This work was performed under the collaboration of the COST action modeling teams and can be used as a review of the state-of-the-art superconductor modeling techniques, and a source for the development and benchmark of future numerical methods.
- 5 November 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (12) , 125006
Electromagnetic-thermal modeling of high-temperature superconducting coils with homogenized method and different formulations: a benchmark
High-temperature superconducting coils are used in various large-scale applications, like rotating machines and high-field magnets. However, modeling these coils is a complicated and time-consuming process, especially due to the non-linearity of the current–voltage characteristics of the superconductors and the complex multiphysics involved. In this work, we used a fast homogenized method to model the coupled electromagnetic and electrothermal properties of racetrack and pancake coils for different applications. For this purpose, various formulations wielding homogenization methods are used and benchmarked with each other, as well as with models considering the detailed structure of the HTS tapes. We observe a very good agreement between different models (homogenized and detailed), and we discuss the pros and cons of the inclusion of insulating layers between the turns in homogenization. This work was performed under the collaboration of the COST action modeling teams and can be used as a review of the state-of-the-art superconductor modeling techniques, and a source for the development and benchmark of future numerical methods.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Subscale Stress-Managed Common Coil Design
In the context of the High-Field Magnet (HFM) Programme, hosted at CERN, and the Swiss Accelerator Research and Technology (CHART) Initiative, hosted at PSI, the Magnet Development (MagDev) project aims to contribute to the Future Circular Collider (FCC) studies through, among others: (i) research on enabling technologies and (ii) high-field Low Temperature superconducting (LTS) and High Temperature Superconducting (HTS) magnets. After a first experience with the CD1 magnet, a Canted-Cosine-Theta (CCT) Nb 3 Sn demonstrator, a roadmap has been established with milestones ranging from enabling technologies tested in powered samples and coils, to ultimate-field and hybrid LTS/HTS short magnets. This article describes the conceptual design of the subscale stress-managed common-coils platform, which is an R&D vehicle for testing enabling technologies, innovative design concepts, and LTS and hybrid LTS/HTS coils. The different aspects of the design will be discussed, including the concept proposed for this platform, magnetic design, coil-ends optimization, and mechanical analysis.
- 14 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Subscale Stress-Managed Common Coil Design
In the context of the High-Field Magnet (HFM) Programme, hosted at CERN, and the Swiss Accelerator Research and Technology (CHART) Initiative, hosted at PSI, the Magnet Development (MagDev) project aims to contribute to the Future Circular Collider (FCC) studies through, among others: (i) research on enabling technologies and (ii) high-field Low Temperature superconducting (LTS) and High Temperature Superconducting (HTS) magnets. After a first experience with the CD1 magnet, a Canted-Cosine-Theta (CCT) Nb 3 Sn demonstrator, a roadmap has been established with milestones ranging from enabling technologies tested in powered samples and coils, to ultimate-field and hybrid LTS/HTS short magnets. This article describes the conceptual design of the subscale stress-managed common-coils platform, which is an R&D vehicle for testing enabling technologies, innovative design concepts, and LTS and hybrid LTS/HTS coils. The different aspects of the design will be discussed, including the concept proposed for this platform, magnetic design, coil-ends optimization, and mechanical analysis.
- Open Access
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-7
Transversal Thermal Conductivity of HTS Tapes: Analytical Method vs Measurements
Design of ReBCO HTS magnets requires reliable data about the tape and insulation thermal conductivities. Material properties represent one of the largest uncertainties when simulating the HTS magnet thermal behavior during magnet cooling, operation, and possible quench scenarios. In this study, we aimed to measure transversal thermal conductivity of insulated and non-insulated HTS tape stacks. Measurements were done in the vacuum of a conduction cooled cryostat. This allows near adiabatic boundary conditions. The measurement results were compared with an analytical model based on thermal conductivities from literature sources. It is noteworthy that the uncertainties associated with the tape material layer thicknesses already constitute a major uncertainty in the magnet analysis. Furthermore, we discuss the challenges, lessons learned and possible future improvements in the measurement methodology.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-7
Open AccessTransversal Thermal Conductivity of HTS Tapes: Analytical Method vs Measurements
Design of ReBCO HTS magnets requires reliable data about the tape and insulation thermal conductivities. Material properties represent one of the largest uncertainties when simulating the HTS magnet thermal behavior during magnet cooling, operation, and possible quench scenarios. In this study, we aimed to measure transversal thermal conductivity of insulated and non-insulated HTS tape stacks. Measurements were done in the vacuum of a conduction cooled cryostat. This allows near adiabatic boundary conditions. The measurement results were compared with an analytical model based on thermal conductivities from literature sources. It is noteworthy that the uncertainties associated with the tape material layer thicknesses already constitute a major uncertainty in the magnet analysis. Furthermore, we discuss the challenges, lessons learned and possible future improvements in the measurement methodology.
- Open Access
- 9 June 2023
- Published by Wiley in Journal of Mechanical Design
- Vol. 145 (8) , 1-27
A Dimension Selection-Based Constrained Multi-Objective Optimization Algorithm Using a Combination of Artificial Intelligence Methods
The computational cost of modern simulation-based optimization tends to be prohibitive in practice. Complex design problems often involve expensive constraints evaluated through finite element analysis or other computationally intensive procedures. To speed up the optimization process and deal with expensive constraints, a new dimension selection-based constrained multi-objective optimization (MOO) algorithm is developed combining least absolute shrinkage and selection operator (LASSO) regression, artificial neural networks, and grey wolf optimizer, named L-ANN-GWO. Instead of considering all variables at each iteration during the optimization, the proposed algorithm only adaptively retains the variables that are highly influential on the objectives. The unselected variables are adjusted to satisfy the constraints through a local search. With numerical benchmark problems and a simulation-based engineering design problem, L-ANN-GWO outperforms state-of-the-art constrained MOO algorithms. The method is then applied to solve a highly complex optimization problem, the design of a high-temperature superconducting magnet. The optimal solution shows significant improvement as compared to the baseline design.
- 9 June 2023
- Published by Wiley in Journal of Mechanical Design
- Vol. 145 (8) , 1-27
Open AccessA Dimension Selection-Based Constrained Multi-Objective Optimization Algorithm Using a Combination of Artificial Intelligence Methods
The computational cost of modern simulation-based optimization tends to be prohibitive in practice. Complex design problems often involve expensive constraints evaluated through finite element analysis or other computationally intensive procedures. To speed up the optimization process and deal with expensive constraints, a new dimension selection-based constrained multi-objective optimization (MOO) algorithm is developed combining least absolute shrinkage and selection operator (LASSO) regression, artificial neural networks, and grey wolf optimizer, named L-ANN-GWO. Instead of considering all variables at each iteration during the optimization, the proposed algorithm only adaptively retains the variables that are highly influential on the objectives. The unselected variables are adjusted to satisfy the constraints through a local search. With numerical benchmark problems and a simulation-based engineering design problem, L-ANN-GWO outperforms state-of-the-art constrained MOO algorithms. The method is then applied to solve a highly complex optimization problem, the design of a high-temperature superconducting magnet. The optimal solution shows significant improvement as compared to the baseline design.
- 27 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Prediction of 2G HTS Tape Quench Behavior by Random Forest Model Trained on 2-D FEM Simulations
Detailed Finite Element Method (FEM) based simulations for 2G HTS tapes return high quality results, but the computation takes a long time due to the non-linearity of superconducting properties and they needed high mesh density. This work describes a method for prediction of quench behavior in a long 2G HTS tape based on a series of 2D FEM model simulations for short length of tape in many different conditions. The random forest model is trained by the set of results from the short-pieces FEM calculations. Subsequently the model can be applied to any length of HTS tape with similar thermal characteristics. Comparison of quench simulation in 10 cm long HTS tape between a detailed FEM model and a fully trained random forest model show that the predicted temperatures are within 0.68%, while the computation time is significantly faster: The random forest model ran in less than 1 s, while the run time of the FEM model was 5:30 min.
- 27 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Prediction of 2G HTS Tape Quench Behavior by Random Forest Model Trained on 2-D FEM Simulations
Detailed Finite Element Method (FEM) based simulations for 2G HTS tapes return high quality results, but the computation takes a long time due to the non-linearity of superconducting properties and they needed high mesh density. This work describes a method for prediction of quench behavior in a long 2G HTS tape based on a series of 2D FEM model simulations for short length of tape in many different conditions. The random forest model is trained by the set of results from the short-pieces FEM calculations. Subsequently the model can be applied to any length of HTS tape with similar thermal characteristics. Comparison of quench simulation in 10 cm long HTS tape between a detailed FEM model and a fully trained random forest model show that the predicted temperatures are within 0.68%, while the computation time is significantly faster: The random forest model ran in less than 1 s, while the run time of the FEM model was 5:30 min.