Jaroslav Bušek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jaroslav Bušek has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Tomáš Vyhlídal
Department of Instrumentation and Control Engineering, Faculty of Mechanical Engineering, Czech Technical University in Prague, Praha, Czech Republic
9 shared publications - Matěj Kuře
Department of Instrumentation and Control Engineering, Faculty of Mechanical Engineering and the Czech Institute of Informatics, Robotics and Cybernetics, Czech Technical University in Prague, Prague, Czechia
4 shared publications - Silviu-Iulian Niculescu
Universit Paris-Saclay, CNRS, CentraleSuplec, Inria, Laboratoire des Signaux et Systmes, Gif-sur-Yvette, France
4 shared publications - Wim Michiels
Department of Computer Science, KU Leuven, Heverlee, Belgium
3 shared publications - Can Kutlu Yuksel2 shared publications
- Milan Anderle
Czech Acad Sci, Inst Informat Theory & Automation UTIA CR, Prague 8, Czech Republic
2 shared publications
Latest Publications
- Open Access
- 16 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (1) , 675-685
Single-Rod Brachiation Robot: Mechatronic Control Design and Validation of Prejump Phases
A completemechatronic design of a minimal configuration brachiation robot is presented. The robot consists of a single rigid rod with gripper mechanisms attached to both ends. The grippers are used to hang the robot on a horizontal bar on which it swings or rotates. The motion is imposed by repositioning the robot’s center of mass, which is performed using a crank-slide mechanism. Based on a nonlinear model, an optimal control strategy is proposed, for repositioning the center of mass in a bang-bang manner. Consequently, utilizing the concept of input–output linearization, a continuous control strategy is proposed that takes into account the limited torque of the crank-slide mechanism and its geometry. An increased attention is paid to energy accumulation towards the subsequent jump stage of the brachiation. These two strategies are validated and compared in simulations. The continuous control strategy is then also implemented within a low-cost STM32-based control system, and both the swing and rotation stages of the brachiation motion are experimentally validated.
- 16 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (1) , 675-685
Open AccessSingle-Rod Brachiation Robot: Mechatronic Control Design and Validation of Prejump Phases
A completemechatronic design of a minimal configuration brachiation robot is presented. The robot consists of a single rigid rod with gripper mechanisms attached to both ends. The grippers are used to hang the robot on a horizontal bar on which it swings or rotates. The motion is imposed by repositioning the robot’s center of mass, which is performed using a crank-slide mechanism. Based on a nonlinear model, an optimal control strategy is proposed, for repositioning the center of mass in a bang-bang manner. Consequently, utilizing the concept of input–output linearization, a continuous control strategy is proposed that takes into account the limited torque of the crank-slide mechanism and its geometry. An increased attention is paid to energy accumulation towards the subsequent jump stage of the brachiation. These two strategies are validated and compared in simulations. The continuous control strategy is then also implemented within a low-cost STM32-based control system, and both the swing and rotation stages of the brachiation motion are experimentally validated.
- Open Access
- 22 January 2025
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 604
A spectrum-based filter design for periodic control of systems with time delay
- 22 January 2025
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 604
Open AccessA spectrum-based filter design for periodic control of systems with time delay
- 18 January 2024
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 576
Robust delayed resonator with acceleration feedback — design by double root assignment and experimental validation
- 18 January 2024
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 576
Robust delayed resonator with acceleration feedback — design by double root assignment and experimental validation
- 10 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 32 (1) , 73-85
Spectral Design and Experimental Validation of Noncollocated Vibration Suppression by a Delayed Resonator and Time-Delay Controller
A generally applicable spectral design to realize noncollocated vibration suppression performed primarily by a delayed resonator (DR) is presented. The vibration suppression is achieved by direct assignment of imaginary axis zeros of the receptance, i.e., the transfer function between the periodic disturbance force and the target’s displacement. To increase the stability margin and to widen the range of frequencies which can be suppressed, the noncollocated vibration absorption by a DR is supplemented by a stabilizing controller tuned by spectral optimization. A unifying aspect of the resonator and the controller is that both use time-delayed output feedback where both the gains and delays are used as controller parameters. Another important aspect of the proposed method is that it can be applied to a system of general structure, where possibly paths exist between the entry point of the disturbance force and the noncollocated absorber that bypass the suppression target, thereby precluding the existence of a resonating substructure. The proposed method has been experimentally validated on a multi-degree of freedom (DOF) experimental setup actuated by voice coils.
- 10 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 32 (1) , 73-85
Spectral Design and Experimental Validation of Noncollocated Vibration Suppression by a Delayed Resonator and Time-Delay Controller
A generally applicable spectral design to realize noncollocated vibration suppression performed primarily by a delayed resonator (DR) is presented. The vibration suppression is achieved by direct assignment of imaginary axis zeros of the receptance, i.e., the transfer function between the periodic disturbance force and the target’s displacement. To increase the stability margin and to widen the range of frequencies which can be suppressed, the noncollocated vibration absorption by a DR is supplemented by a stabilizing controller tuned by spectral optimization. A unifying aspect of the resonator and the controller is that both use time-delayed output feedback where both the gains and delays are used as controller parameters. Another important aspect of the proposed method is that it can be applied to a system of general structure, where possibly paths exist between the entry point of the disturbance force and the noncollocated absorber that bypass the suppression target, thereby precluding the existence of a resonating substructure. The proposed method has been experimentally validated on a multi-degree of freedom (DOF) experimental setup actuated by voice coils.
- 10 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 28 (5) , 2864-2875
Harmonic Disturbance Compensation of a System With Long Dead-Time, Design and Experimental Validation
An internal model control scheme is proposed to compensate both a long dead-time of a system and a harmonic disturbance. The controller is based on an inversion of the first-order model used to approximate the system dynamics together with an input delay. Two other components of the controller consist of a filter and an additional delay by which the harmonic modes are targeted via adjusting the control loop gain and phase shift. The design of the filter-delay pair is fully analytical and the implementation of the scheme is straightforward. The main attention is paid to the complete compensation of a single-harmonic disturbance. Besides, an extension of the scheme is proposed to target a double harmonic disturbance. Increased attention is paid to the robustness aspects of the schemes. Outstanding performance in terms of harmonic disturbance compensation of the proposed schemes is demonstrated on a series of laboratory experiments.
- 10 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 28 (5) , 2864-2875
Harmonic Disturbance Compensation of a System With Long Dead-Time, Design and Experimental Validation
An internal model control scheme is proposed to compensate both a long dead-time of a system and a harmonic disturbance. The controller is based on an inversion of the first-order model used to approximate the system dynamics together with an input delay. Two other components of the controller consist of a filter and an additional delay by which the harmonic modes are targeted via adjusting the control loop gain and phase shift. The design of the filter-delay pair is fully analytical and the implementation of the scheme is straightforward. The main attention is paid to the complete compensation of a single-harmonic disturbance. Besides, an extension of the scheme is proposed to target a double harmonic disturbance. Increased attention is paid to the robustness aspects of the schemes. Outstanding performance in terms of harmonic disturbance compensation of the proposed schemes is demonstrated on a series of laboratory experiments.
- 1 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 7-12
Swing compensation of a payload suspended to a planar copter
A switching strategy to compensate copter's sus- pended payload swing is presented. In order to prevent the payload swing during the maneuvers, the inverse input shaper is placed to the feedback loop. This approach prevents payload swinging in presence of set-point change or control input disturbance. Nevertheless, in case of external disturbance acting on payload directly, input shaper is powerless. Therefore, a nonlinear time-delayed algorithm is involved to suppress the residual swing by up and down motion of the copter. However, there's no need to use that algorithm all the time. Thus, a switching strategy between the two algorithms is developed and presented. A simulation based verification is performed to validate the results.
- 1 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 7-12
Swing compensation of a payload suspended to a planar copter
A switching strategy to compensate copter's sus- pended payload swing is presented. In order to prevent the payload swing during the maneuvers, the inverse input shaper is placed to the feedback loop. This approach prevents payload swinging in presence of set-point change or control input disturbance. Nevertheless, in case of external disturbance acting on payload directly, input shaper is powerless. Therefore, a nonlinear time-delayed algorithm is involved to suppress the residual swing by up and down motion of the copter. However, there's no need to use that algorithm all the time. Thus, a switching strategy between the two algorithms is developed and presented. A simulation based verification is performed to validate the results.
- 13 April 2014
- Published by Springer Nature
- p. 31-45
Anti-Windup Conditioning for Actuator Saturation in Internal Model Control with Delays
- 13 April 2014
- Published by Springer Nature
- p. 31-45
Anti-Windup Conditioning for Actuator Saturation in Internal Model Control with Delays