Yaroslava Bachurina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yaroslava Bachurina has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Daria Chepiga
Donetsk National Technical University
8 shared publications - Leonid Bachurin
Donetsk National Technical University
8 shared publications - Olena Visyn
Lutsk National Technical University
6 shared publications - Serhii Podkopaiev
Lutsk National Technical University
6 shared publications - Yevgen Podkopayev
Limited Liability Company Manufacturing Company ELTEKO
6 shared publications - Danylo Polii
Donetsk National Technical University
4 shared publications
Latest Publications
- Open Access
- 30 April 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (140)) , 13-24
Assessment of the bearing capacity of rigid secondary support systems for gob-side retained entries based on strain energy analysis
This study investigates deformation processes occurring in secondary support systems for gob-side retained entries in coal mine extraction panels mining thin seams. The task addressed is to stabilize gob-side retained entries by improving the bearing capacity of secondary support systems to prevent roof collapses and provide safe working conditions. The comparative assessment was conducted based on an analysis of strain energy-related indicators. Underlying the study are physical models simulating filling walls, concrete blocks, and combined structures consisting of blocks with wooden interlayers. During uniaxial compression tests, the deformation capacity of each type of support system was determined; critical values of relative deformation at which the structures lose their functional performance were identified. The application of an energy-based approach has made it possible to quantify the stability limit and to predict the onset of structural failure. Experimental results showed that, under uniaxial compression, rigid secondary support systems operate under an increasing resistance mode before the initiation of failure processes. At the same time, the range of linear elastic deformation of the combined support structure is 33% greater than that of the homogeneous structure (damage initiation occurs at λb = 0.103 and λb = 0.075–0.08, respectively), which results in a delayed transition to loss of bearing capacity. The incorporation of limited yielding elements into rigid structures facilitates stress redistribution and enhances their deformation capacity. An energy-based approach to analyzing the interaction between secondary support systems and the surrounding rock mass has been proposed, based on the use of strain energy density and its components, which characterize the processes of energy accumulation and dissipation. The practical significance of this study is associated with the application of the results to substantiate the design parameters for rigid secondary support systems for gob-side retained entries in coal extraction panels mining thin seams up to 1.2 m thick
- 30 April 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (140)) , 13-24
Open AccessAssessment of the bearing capacity of rigid secondary support systems for gob-side retained entries based on strain energy analysis
This study investigates deformation processes occurring in secondary support systems for gob-side retained entries in coal mine extraction panels mining thin seams. The task addressed is to stabilize gob-side retained entries by improving the bearing capacity of secondary support systems to prevent roof collapses and provide safe working conditions. The comparative assessment was conducted based on an analysis of strain energy-related indicators. Underlying the study are physical models simulating filling walls, concrete blocks, and combined structures consisting of blocks with wooden interlayers. During uniaxial compression tests, the deformation capacity of each type of support system was determined; critical values of relative deformation at which the structures lose their functional performance were identified. The application of an energy-based approach has made it possible to quantify the stability limit and to predict the onset of structural failure. Experimental results showed that, under uniaxial compression, rigid secondary support systems operate under an increasing resistance mode before the initiation of failure processes. At the same time, the range of linear elastic deformation of the combined support structure is 33% greater than that of the homogeneous structure (damage initiation occurs at λb = 0.103 and λb = 0.075–0.08, respectively), which results in a delayed transition to loss of bearing capacity. The incorporation of limited yielding elements into rigid structures facilitates stress redistribution and enhances their deformation capacity. An energy-based approach to analyzing the interaction between secondary support systems and the surrounding rock mass has been proposed, based on the use of strain energy density and its components, which characterize the processes of energy accumulation and dissipation. The practical significance of this study is associated with the application of the results to substantiate the design parameters for rigid secondary support systems for gob-side retained entries in coal extraction panels mining thin seams up to 1.2 m thick
- 1 January 2026
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- Vol. 2 (17)
ASSESSING THE BEARING CAPACITY OF CRUSHED-ROCK BACKFILL MASSES BASED ON DEFORMATION-ENERGY INDICATORS UNDER DIFFERENT COMPRESSION CONDITIONS
Purpose. To assess the bearing capacity of backfill masses under various compression conditions based on deformation-energy indicators to limit displacements and prevent wall rock caving during the maintenance of mine workings in the goaf behind the longwall face. Methods. Scale models subjected to gradual loading on a press were used to evaluate the bearing capacity of backfill masses. Modeling of uniaxial compression of crushed rock corresponded to partial backfilling, while confined compression testing corresponded to full backfilling of the goaf. Findings. Under confined compression (full backfilling), the backfill material evolves from a loose polyfractional mixture to a pseudo-elastic conglomerate. The ratio of the total potential deformation energy to the tangential deformation modulus – deformation energy indicator R – initially increases, reflecting intensive dissipation on grain repacking and void closure. Subsequently, when the matrix is fully formed and operates stably, it decreases and levels off to a horizontal asymptote. This constant is determined by the parameters of an "ideal" exponential "stress-strain" relationship. Under uniaxial compression (with the possibility of lateral expansion), the R indicator reflects the loss of bearing capacity of the formed mass and the transition to the macro-failure stage. This process follows a hyperbolic law, where the point of ultimate loss of bearing capacity is a vertical asymptote (R→∞). Under such conditions, the R indicator becomes a stability index: if R is small and stable, the material continues to function; the onset of sharp exponential growth in R marks irreversible processes within the system. The transition of R through infinity into the range of negative values represents the moment of complete mechanical disintegration of the load-bearing structure. Originality. A deformation energy indicator R is proposed, which equals the ratio of the total potential deformation energy to the tangential deformation modulus. Based on experimental data, the asymptotic nature of the R indicator's dependence on the material's relative deformation under different compression conditions is shown. Practical implications. Analysis of the rate of change of the deformation energy indicator R allows for predicting the loss of bearing capacity even before the stresses reach limit values. The results can be used to justify ground control methods in coal mines and in the development of methods for monitoring the state of secondary support structures. Keywords: backfill mass, specific strain energy, bearing capacity, deformation processes, secondary support structures.
- 1 January 2026
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- Vol. 2 (17)
ASSESSING THE BEARING CAPACITY OF CRUSHED-ROCK BACKFILL MASSES BASED ON DEFORMATION-ENERGY INDICATORS UNDER DIFFERENT COMPRESSION CONDITIONS
Purpose. To assess the bearing capacity of backfill masses under various compression conditions based on deformation-energy indicators to limit displacements and prevent wall rock caving during the maintenance of mine workings in the goaf behind the longwall face. Methods. Scale models subjected to gradual loading on a press were used to evaluate the bearing capacity of backfill masses. Modeling of uniaxial compression of crushed rock corresponded to partial backfilling, while confined compression testing corresponded to full backfilling of the goaf. Findings. Under confined compression (full backfilling), the backfill material evolves from a loose polyfractional mixture to a pseudo-elastic conglomerate. The ratio of the total potential deformation energy to the tangential deformation modulus – deformation energy indicator R – initially increases, reflecting intensive dissipation on grain repacking and void closure. Subsequently, when the matrix is fully formed and operates stably, it decreases and levels off to a horizontal asymptote. This constant is determined by the parameters of an "ideal" exponential "stress-strain" relationship. Under uniaxial compression (with the possibility of lateral expansion), the R indicator reflects the loss of bearing capacity of the formed mass and the transition to the macro-failure stage. This process follows a hyperbolic law, where the point of ultimate loss of bearing capacity is a vertical asymptote (R→∞). Under such conditions, the R indicator becomes a stability index: if R is small and stable, the material continues to function; the onset of sharp exponential growth in R marks irreversible processes within the system. The transition of R through infinity into the range of negative values represents the moment of complete mechanical disintegration of the load-bearing structure. Originality. A deformation energy indicator R is proposed, which equals the ratio of the total potential deformation energy to the tangential deformation modulus. Based on experimental data, the asymptotic nature of the R indicator's dependence on the material's relative deformation under different compression conditions is shown. Practical implications. Analysis of the rate of change of the deformation energy indicator R allows for predicting the loss of bearing capacity even before the stresses reach limit values. The results can be used to justify ground control methods in coal mines and in the development of methods for monitoring the state of secondary support structures. Keywords: backfill mass, specific strain energy, bearing capacity, deformation processes, secondary support structures.
- Open Access
- 31 December 2025
- Published by National Scientific and Research Institute of Industrial Safety and Occupational Safety and Health in Labour protection problems in Ukraine
- Vol. 41 (3-4)
ASSESSMENT OF THE BEARING CAPACITY OF SECONDARY SUPPORT STRUCTURES FOR MAINTAINING MINE ROADWAYS AND PREVENTING ROOF COLLAPSE
Purpose. To evaluate the bearing capacity of secondary support structures for mine roadways maintained within the goaf area, aimed at ensuring their stability and improving occupational safety in longwall mining operations by preventing roof and sidewall collapses. Methodology. The bearing capacity of the secondary support structures was examined using scaled physical models subjected to loading in a hydraulic press. The modelling was qualitative, focused on investigating the deformation mechanism, shape transformation, and sequence of failure of the secondary support structures. Conclusions. For coal pillars, within their deformation range (relative strain λ ≤ 0.1), sufficient bearing capacity is maintained, enabling short-term restriction of side-rock movement under progressive loading. As the relative deformation increases (λ > 0.1), the structures lose their bearing capacity, and the risk of roof collapse approaches a critical level. For timber packs made of wooden sleepers, compaction of structural elements occurs within their deformation range, increasing stiffness. Under these conditions, the bearing capacity of the support structures limits the movement of stratified rock layers. Both coal pillars and timber packs have a limited strength reserve. The deformation capacity of structures made from crushed rock is governed by the achievement of maximum compaction of the initial material, which reduces the relative deformation and enhances stiffness. Practical implications. The stability of mine roadways maintained within the goaf area and the prevention of roof collapse in longwall panels can be achieved by employing secondary support structures with a deformation capacity sufficient to provide the bearing resistance required to limit side-rock movement within the goaf area. Originality. The secondary support structures are considered as load-bearing systems with variable stiffness. The nature of stiffness variation enables the assessment of their deformation capacity and the identification of optimal operating conditions.
- 31 December 2025
- Published by National Scientific and Research Institute of Industrial Safety and Occupational Safety and Health in Labour protection problems in Ukraine
- Vol. 41 (3-4)
Open AccessASSESSMENT OF THE BEARING CAPACITY OF SECONDARY SUPPORT STRUCTURES FOR MAINTAINING MINE ROADWAYS AND PREVENTING ROOF COLLAPSE
Purpose. To evaluate the bearing capacity of secondary support structures for mine roadways maintained within the goaf area, aimed at ensuring their stability and improving occupational safety in longwall mining operations by preventing roof and sidewall collapses. Methodology. The bearing capacity of the secondary support structures was examined using scaled physical models subjected to loading in a hydraulic press. The modelling was qualitative, focused on investigating the deformation mechanism, shape transformation, and sequence of failure of the secondary support structures. Conclusions. For coal pillars, within their deformation range (relative strain λ ≤ 0.1), sufficient bearing capacity is maintained, enabling short-term restriction of side-rock movement under progressive loading. As the relative deformation increases (λ > 0.1), the structures lose their bearing capacity, and the risk of roof collapse approaches a critical level. For timber packs made of wooden sleepers, compaction of structural elements occurs within their deformation range, increasing stiffness. Under these conditions, the bearing capacity of the support structures limits the movement of stratified rock layers. Both coal pillars and timber packs have a limited strength reserve. The deformation capacity of structures made from crushed rock is governed by the achievement of maximum compaction of the initial material, which reduces the relative deformation and enhances stiffness. Practical implications. The stability of mine roadways maintained within the goaf area and the prevention of roof collapse in longwall panels can be achieved by employing secondary support structures with a deformation capacity sufficient to provide the bearing resistance required to limit side-rock movement within the goaf area. Originality. The secondary support structures are considered as load-bearing systems with variable stiffness. The nature of stiffness variation enables the assessment of their deformation capacity and the identification of optimal operating conditions.
- 30 December 2025
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
Assessment of backfill mass stiffness in polyfractional crushed-rock models under compressive compaction
Purpose. To assess the stiffness of backfill masses made of crushed rock with polyfraction-al composition under conditions of complete gob backfilling, to prevent roof collapses in the extraction sections of coal mines. Methods. To simulate complete gob backfilling with crushed rock, compressive compac-tion was applied to scaled model materials with polyfractional grain-size compositions of (0.1–5) mm, (1–5) mm, and (2–5) mm. The deformation process in the backfill masses was examined through laboratory testing of experimental models in a compression device on a hydraulic press. Results. Under compressive compaction of crushed rock with polyfractional composition, displacement restriction during gradual loading occurs when the relative deformation of the backfill mass reaches λ = 0.37–0.38, and the compaction coefficient of the material is kc = 1.59–1.62. The artificially created mass attains maximum stiffness at the highest values of the relative change in rock volume per unit of convergence, ΔVₖ (m⁻¹). The growth rate of ΔVₖ characterizes the process of rearrangement and compaction of the crushed rock and depends on its grain-size distribution. The parameter ΔVₖ serves as an informative indicator of the deformation behavior of the backfill material, since it increases hyperbolically as it approaches the limit values of stiffness. Novelty. A hyperbolic relationship has been established between the relative change in rock volume per unit of convergence ΔVₖ and the stiffness of a backfill mass composed of polyfractional crushed rock under compressive compaction. Practical significance. The stiffness of the backfill mass determines the intensity of roof displacements in the gob areas of longwall panels. Maximum stiffness of the artificially created mass is achieved by a material that possesses a reserve of compaction associated with the rear-rangement of crushed-rock grains.
- 30 December 2025
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
Assessment of backfill mass stiffness in polyfractional crushed-rock models under compressive compaction
Purpose. To assess the stiffness of backfill masses made of crushed rock with polyfraction-al composition under conditions of complete gob backfilling, to prevent roof collapses in the extraction sections of coal mines. Methods. To simulate complete gob backfilling with crushed rock, compressive compac-tion was applied to scaled model materials with polyfractional grain-size compositions of (0.1–5) mm, (1–5) mm, and (2–5) mm. The deformation process in the backfill masses was examined through laboratory testing of experimental models in a compression device on a hydraulic press. Results. Under compressive compaction of crushed rock with polyfractional composition, displacement restriction during gradual loading occurs when the relative deformation of the backfill mass reaches λ = 0.37–0.38, and the compaction coefficient of the material is kc = 1.59–1.62. The artificially created mass attains maximum stiffness at the highest values of the relative change in rock volume per unit of convergence, ΔVₖ (m⁻¹). The growth rate of ΔVₖ characterizes the process of rearrangement and compaction of the crushed rock and depends on its grain-size distribution. The parameter ΔVₖ serves as an informative indicator of the deformation behavior of the backfill material, since it increases hyperbolically as it approaches the limit values of stiffness. Novelty. A hyperbolic relationship has been established between the relative change in rock volume per unit of convergence ΔVₖ and the stiffness of a backfill mass composed of polyfractional crushed rock under compressive compaction. Practical significance. The stiffness of the backfill mass determines the intensity of roof displacements in the gob areas of longwall panels. Maximum stiffness of the artificially created mass is achieved by a material that possesses a reserve of compaction associated with the rear-rangement of crushed-rock grains.
- 27 November 2025
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- Vol. 2 (15)
DETERMINATION OF DEFORMATION PROPERTIES OF BASEMENT MASSES UNDER VARIOUS COMPRESSION CONDITIONS
Purpose. To assess the deformation properties of base materials made of crushed rock of heterogeneous granulometric composition under different compression conditions to substantiate measures to prevent roof collapses in the mining areas of coal mines. Methods. Deformation processes were studied on experimental models that simulated the conditions of complete and partial filling of the mined space with crushed rock. Partial filling corresponded to the conditions of uniaxial compression of the crushed rock with the possibility of its lateral expansion. Full filling - to the conditions of compression compression of the base material. Results. Compaction of the embankment massifs under gradual loading under compression conditions leads to an increase in the deformation modulus Ed (MN/m) more than three times, compared to the conditions of uniaxial compression. The embankment massif, when fully compacted, works as a supporting structure with increasing resistance, which acquires the characteristics of a rigid support when reaching the limit compaction (in this experiment, when reaching the value of the relative deformation λ = 0.381, which is 42% less than under uniaxial compression conditions). The stiffness of the model material in the languages of compression compression is on average 40% greater than under uniaxial compression conditions. Under such conditions, the strength of the massif becomes maximum, the increase in displacements reaches minimum values, and the movements of lateral rocks are limited. Scientific novelty. The dependence between the relative change in the volume of crushed rock of heterogeneous granulometric composition per unit of convergence ΔVK (m⁻¹) and the deformation modulus of the backfill massif, which is under compression compression conditions, has been established. The nature of this dependence allows, based on the results of laboratory tests, to estimate the limiting value of the deformation modulus of the backfill massif when reaching the limit compaction. Practical significance. The estimation of the limiting value of the deformation modulus of the backfill material is necessary to determine the strength of the backfill massifs, which determines the efficiency of holding the forged rock massif and affects the stability of the preparatory workings of the extraction areas and increasing the safety of miners. Keywords: backfilling of the mined space, crushed rock, compaction, uniaxial compression, compression compression, deformation processes
- 27 November 2025
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- Vol. 2 (15)
DETERMINATION OF DEFORMATION PROPERTIES OF BASEMENT MASSES UNDER VARIOUS COMPRESSION CONDITIONS
Purpose. To assess the deformation properties of base materials made of crushed rock of heterogeneous granulometric composition under different compression conditions to substantiate measures to prevent roof collapses in the mining areas of coal mines. Methods. Deformation processes were studied on experimental models that simulated the conditions of complete and partial filling of the mined space with crushed rock. Partial filling corresponded to the conditions of uniaxial compression of the crushed rock with the possibility of its lateral expansion. Full filling - to the conditions of compression compression of the base material. Results. Compaction of the embankment massifs under gradual loading under compression conditions leads to an increase in the deformation modulus Ed (MN/m) more than three times, compared to the conditions of uniaxial compression. The embankment massif, when fully compacted, works as a supporting structure with increasing resistance, which acquires the characteristics of a rigid support when reaching the limit compaction (in this experiment, when reaching the value of the relative deformation λ = 0.381, which is 42% less than under uniaxial compression conditions). The stiffness of the model material in the languages of compression compression is on average 40% greater than under uniaxial compression conditions. Under such conditions, the strength of the massif becomes maximum, the increase in displacements reaches minimum values, and the movements of lateral rocks are limited. Scientific novelty. The dependence between the relative change in the volume of crushed rock of heterogeneous granulometric composition per unit of convergence ΔVK (m⁻¹) and the deformation modulus of the backfill massif, which is under compression compression conditions, has been established. The nature of this dependence allows, based on the results of laboratory tests, to estimate the limiting value of the deformation modulus of the backfill massif when reaching the limit compaction. Practical significance. The estimation of the limiting value of the deformation modulus of the backfill material is necessary to determine the strength of the backfill massifs, which determines the efficiency of holding the forged rock massif and affects the stability of the preparatory workings of the extraction areas and increasing the safety of miners. Keywords: backfilling of the mined space, crushed rock, compaction, uniaxial compression, compression compression, deformation processes
- 30 September 2025
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 19 (3) , 76-86
Specifics of the influence of secondary support deformation characteristics on the gate roadways stability
Purpose. The research is aimed at determining the specifics of the influence of secondary support deformation characteristics on headgate stability in coal mines with steep-dipping seams. Methods. The deformation characteristics of secondary supports are determined in mine conditions based on instrumental observations of the displacement of reference points on the contour of headgate along the extraction site length. Secondary supports studied are in the form of coal pillars and timber packs. Findings. An assessment characteristic of the deformation properties of secondary supports is the ability to ensure the stability of side rocks and headgates in the mined-out space of the coal-rock mass. The determining factor in such an assessment is the load-bearing capacity of secondary supports. A distinctive peculiarity is a certain range of physical-mechanical characteristics and deformation processes, within which the resistance of supporting structures increases. At relative deformation ε ˂ 0.1-0.2, the resistance of coal pillars increases, which ensures the continuity of side rocks around the haulage drift and limits their displacement on the contour. After losing load-bearing capacity (ε ˃ 0.2), there is a periodic subsidence of the roof, which is accompanied by an increment in the displacement of side rocks on the headgate contour. In such conditions, the loss of cross-sectional area of the drifts exceeds 50%. For timber packs, after their compaction (ε = 0.4-0.5), resistance increases, effectively limiting the displacement of side rocks. The loss of cross-sectional area of the drifts does not exceed 30%. Originality. The dependence between the change in cross-sectional area (S) of the haulage drift and relative change in the volume of secondary supports per unit of convergence of side rocks ( ) has been determined. The presence of such dependence makes it possible to assess the state of headgates supported behind the stoping face at the extraction site. Practical implications. Coal pillars perform the functions of a supporting structure only within a certain range of deformation properties. Timber packs after their compaction allow limiting the displacement of side rocks on the headgate contour and ensuring its operational state.
- 30 September 2025
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 19 (3) , 76-86
Specifics of the influence of secondary support deformation characteristics on the gate roadways stability
Purpose. The research is aimed at determining the specifics of the influence of secondary support deformation characteristics on headgate stability in coal mines with steep-dipping seams. Methods. The deformation characteristics of secondary supports are determined in mine conditions based on instrumental observations of the displacement of reference points on the contour of headgate along the extraction site length. Secondary supports studied are in the form of coal pillars and timber packs. Findings. An assessment characteristic of the deformation properties of secondary supports is the ability to ensure the stability of side rocks and headgates in the mined-out space of the coal-rock mass. The determining factor in such an assessment is the load-bearing capacity of secondary supports. A distinctive peculiarity is a certain range of physical-mechanical characteristics and deformation processes, within which the resistance of supporting structures increases. At relative deformation ε ˂ 0.1-0.2, the resistance of coal pillars increases, which ensures the continuity of side rocks around the haulage drift and limits their displacement on the contour. After losing load-bearing capacity (ε ˃ 0.2), there is a periodic subsidence of the roof, which is accompanied by an increment in the displacement of side rocks on the headgate contour. In such conditions, the loss of cross-sectional area of the drifts exceeds 50%. For timber packs, after their compaction (ε = 0.4-0.5), resistance increases, effectively limiting the displacement of side rocks. The loss of cross-sectional area of the drifts does not exceed 30%. Originality. The dependence between the change in cross-sectional area (S) of the haulage drift and relative change in the volume of secondary supports per unit of convergence of side rocks ( ) has been determined. The presence of such dependence makes it possible to assess the state of headgates supported behind the stoping face at the extraction site. Practical implications. Coal pillars perform the functions of a supporting structure only within a certain range of deformation properties. Timber packs after their compaction allow limiting the displacement of side rocks on the headgate contour and ensuring its operational state.
- Open Access
- 30 August 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 4 (1(84)) , 50-57
Assessment of deformation processes in backfill masses using crushed rock models
The object of the study was the deformation processes in backfill masses made of crushed rock, which are used for roof control in mining panels. The study addressed the issue of preventing sidewall collapses by ensuring the stability of the backfill masses. Deformation processes were investigated using experimental models made of crushed rock that simulated various backfill structures. The study considered uniaxial compression of crushed rock with lateral expansion capability, as well as compressive loading. Uniaxial compression was used to simulate partial backfilling of the gob area, while compressive loading represented complete backfilling. Under loading conditions, a hyperbolic relationship was established between the relative volume change of the backfill material per unit of side rock convergence, ΔVK (m–1), and the compaction coefficient of crushed rock. This relationship enables the prediction of the material's ultimate settlement. The determining factor in this relationship is the relative deformation of the backfill mass. Under loading of crushed rock and comparable compaction coefficient values, the difference in deformation properties reaches 2.5 to 3 times. This is recorded due to the transformation of shape or change in volume under different compression conditions. It is shown that with an increase in the parameter ΔVK, the specific potential energy of deformation of the backfill material changes according to a logarithmic relationship. The specific potential energy of deformation is determined by the mechanical properties and compression conditions of the crushed rock. Maximum stability of gob-side retained entries can be ensured through complete backfilling of the gob area, while the expected subsidence of the backfill mass depends on the initial backfill density and the deformation properties of the crushed rock used for filling.
- 30 August 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 4 (1(84)) , 50-57
Open AccessAssessment of deformation processes in backfill masses using crushed rock models
The object of the study was the deformation processes in backfill masses made of crushed rock, which are used for roof control in mining panels. The study addressed the issue of preventing sidewall collapses by ensuring the stability of the backfill masses. Deformation processes were investigated using experimental models made of crushed rock that simulated various backfill structures. The study considered uniaxial compression of crushed rock with lateral expansion capability, as well as compressive loading. Uniaxial compression was used to simulate partial backfilling of the gob area, while compressive loading represented complete backfilling. Under loading conditions, a hyperbolic relationship was established between the relative volume change of the backfill material per unit of side rock convergence, ΔVK (m–1), and the compaction coefficient of crushed rock. This relationship enables the prediction of the material's ultimate settlement. The determining factor in this relationship is the relative deformation of the backfill mass. Under loading of crushed rock and comparable compaction coefficient values, the difference in deformation properties reaches 2.5 to 3 times. This is recorded due to the transformation of shape or change in volume under different compression conditions. It is shown that with an increase in the parameter ΔVK, the specific potential energy of deformation of the backfill material changes according to a logarithmic relationship. The specific potential energy of deformation is determined by the mechanical properties and compression conditions of the crushed rock. Maximum stability of gob-side retained entries can be ensured through complete backfilling of the gob area, while the expected subsidence of the backfill mass depends on the initial backfill density and the deformation properties of the crushed rock used for filling.
- Open Access
- 28 August 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7 (136)) , 32-41
Evaluation of deformation characteristics and bearing capacity assessment of crushed-rock backfill with various grain size distributions
This study addresses issues related to deformation processes in crushed rock backfills, which are used to control the condition of surrounding rocks in the extraction areas of coal mines. The task under consideration is to maintain mine roadway stability by preventing roof collapses in the gob area by ensuring the bearing capacity of backfills. Deformation processes were studied on model materials made of crushed rock of various grain-size distributions and bulk densities. The material was subjected to compression testing, which simulated the complete backfilling of the gob area. It was shown that the energy characteristics of deformation and compaction of crushed rock determine the bearing capacity of backfills. The deformation energy density was determined by the grain-size distribution of the crushed rock with a polyfractional composition. The maximum values of the specific potential deformation energy were recorded during compression of crushed rock with a coefficient of uniformity Сu = 5.99, which has a stiffness 7–13% higher than that of polyfractional materials with Сu < 4, which ensures the bearing capacity of the backfill mass. It was established that with an increase in the compaction coefficient of the backfill material, the relative volume change per unit of convergence, ΔVK (m⁻1), occurs according to a hyperbolic relationship, allowing the prediction of the ultimate compaction of the backfill material. The stability of gob-side retained entries can be ensured by complete gob backfilling. The expected settlement of the backfill material determines the nature of the limitation of lateral rock movements in the gob area, the bearing capacity of the artificial massif, and depends on the grain-size distribution of the crushed rock
- 28 August 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7 (136)) , 32-41
Open AccessEvaluation of deformation characteristics and bearing capacity assessment of crushed-rock backfill with various grain size distributions
This study addresses issues related to deformation processes in crushed rock backfills, which are used to control the condition of surrounding rocks in the extraction areas of coal mines. The task under consideration is to maintain mine roadway stability by preventing roof collapses in the gob area by ensuring the bearing capacity of backfills. Deformation processes were studied on model materials made of crushed rock of various grain-size distributions and bulk densities. The material was subjected to compression testing, which simulated the complete backfilling of the gob area. It was shown that the energy characteristics of deformation and compaction of crushed rock determine the bearing capacity of backfills. The deformation energy density was determined by the grain-size distribution of the crushed rock with a polyfractional composition. The maximum values of the specific potential deformation energy were recorded during compression of crushed rock with a coefficient of uniformity Сu = 5.99, which has a stiffness 7–13% higher than that of polyfractional materials with Сu < 4, which ensures the bearing capacity of the backfill mass. It was established that with an increase in the compaction coefficient of the backfill material, the relative volume change per unit of convergence, ΔVK (m⁻1), occurs according to a hyperbolic relationship, allowing the prediction of the ultimate compaction of the backfill material. The stability of gob-side retained entries can be ensured by complete gob backfilling. The expected settlement of the backfill material determines the nature of the limitation of lateral rock movements in the gob area, the bearing capacity of the artificial massif, and depends on the grain-size distribution of the crushed rock
- Open Access
- 28 April 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (122)) , 73-81
Evaluation of the effectiveness of secondary support of haulage drifts based on a comparative analysis of the deformation characteristics of protective structures
The object of this study is the processes of managing the state of lateral rocks in the coal rock array with preparatory workings. The influence of deformation characteristics of the protective structures of the preparatory workings on the stability of lateral rocks in the coal rock array has been established. The stable state of the above-the-drift pillars of coal is provided within the deformation resource, which corresponds to the critical level of the specific potential energy of the deformation. The limits of the deformation resource are the range of change in the relative deformation of coal pillars 0.1≤λ≤0.25. When the critical level of the specific potential energy of deformation is passed, at λ˃0.25, there is a relative change in the volume of pillars δλ˃0,1, as a result of which their durability decreases and the state changes. Under such conditions, the residual strength of coal pillars is not enough to limit the movement of lateral rocks, which provokes their collapse. For protective structures made of crushed rock, within the established deformation resource of 0.4≤λ≤0.7, with an increase in static load and cross-sectional area, the specific potential energy of deformation decreases, simultaneously with the relative change in the volume of the embedded material. This is due to the compaction of the crushed rock and an increase in its strength. Regularities of change in the specific potential energy of deformation of protective structures have been established, which, under conditions of uniaxial compression, make it possible to assess, within the deformation resource, their stability. To ensure the stability of lateral rocks in the coal rock array and to preserve the operational condition of the preparatory workings, it is advisable to use protective structures made of crushed rock. This method will limit the movement of the roof and sole in the produced space and avoid collapses.
- 28 April 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (122)) , 73-81
Open AccessEvaluation of the effectiveness of secondary support of haulage drifts based on a comparative analysis of the deformation characteristics of protective structures
The object of this study is the processes of managing the state of lateral rocks in the coal rock array with preparatory workings. The influence of deformation characteristics of the protective structures of the preparatory workings on the stability of lateral rocks in the coal rock array has been established. The stable state of the above-the-drift pillars of coal is provided within the deformation resource, which corresponds to the critical level of the specific potential energy of the deformation. The limits of the deformation resource are the range of change in the relative deformation of coal pillars 0.1≤λ≤0.25. When the critical level of the specific potential energy of deformation is passed, at λ˃0.25, there is a relative change in the volume of pillars δλ˃0,1, as a result of which their durability decreases and the state changes. Under such conditions, the residual strength of coal pillars is not enough to limit the movement of lateral rocks, which provokes their collapse. For protective structures made of crushed rock, within the established deformation resource of 0.4≤λ≤0.7, with an increase in static load and cross-sectional area, the specific potential energy of deformation decreases, simultaneously with the relative change in the volume of the embedded material. This is due to the compaction of the crushed rock and an increase in its strength. Regularities of change in the specific potential energy of deformation of protective structures have been established, which, under conditions of uniaxial compression, make it possible to assess, within the deformation resource, their stability. To ensure the stability of lateral rocks in the coal rock array and to preserve the operational condition of the preparatory workings, it is advisable to use protective structures made of crushed rock. This method will limit the movement of the roof and sole in the produced space and avoid collapses.