Serhii Podkopaiev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Serhii Podkopaiev has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Daria Chepiga
Donetsk National Technical University
10 shared publications Donetsk National Technical University
6 shared publications- Iaroslav Liashok4 shared publications
Oleksandr Tkachuk
PJSC «Donbasenergo» «Elektroremont
4 shared publications- Yuliia Simonova
State Higher Education Establishment «Donetsk National Technical University
4 shared publications - Iryna Bessarab
Donetsk National Technical University
3 shared publications
Latest Publications
- 30 September 2025
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 19 (3) , 76-86
Specifics of the influence of secondary support deformation characteristics on the gate roadways stability
Purpose. The research is aimed at determining the specifics of the influence of secondary support deformation characteristics on headgate stability in coal mines with steep-dipping seams. Methods. The deformation characteristics of secondary supports are determined in mine conditions based on instrumental observations of the displacement of reference points on the contour of headgate along the extraction site length. Secondary supports studied are in the form of coal pillars and timber packs. Findings. An assessment characteristic of the deformation properties of secondary supports is the ability to ensure the stability of side rocks and headgates in the mined-out space of the coal-rock mass. The determining factor in such an assessment is the load-bearing capacity of secondary supports. A distinctive peculiarity is a certain range of physical-mechanical characteristics and deformation processes, within which the resistance of supporting structures increases. At relative deformation ε ˂ 0.1-0.2, the resistance of coal pillars increases, which ensures the continuity of side rocks around the haulage drift and limits their displacement on the contour. After losing load-bearing capacity (ε ˃ 0.2), there is a periodic subsidence of the roof, which is accompanied by an increment in the displacement of side rocks on the headgate contour. In such conditions, the loss of cross-sectional area of the drifts exceeds 50%. For timber packs, after their compaction (ε = 0.4-0.5), resistance increases, effectively limiting the displacement of side rocks. The loss of cross-sectional area of the drifts does not exceed 30%. Originality. The dependence between the change in cross-sectional area (S) of the haulage drift and relative change in the volume of secondary supports per unit of convergence of side rocks ( ) has been determined. The presence of such dependence makes it possible to assess the state of headgates supported behind the stoping face at the extraction site. Practical implications. Coal pillars perform the functions of a supporting structure only within a certain range of deformation properties. Timber packs after their compaction allow limiting the displacement of side rocks on the headgate contour and ensuring its operational state.
- 30 September 2025
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 19 (3) , 76-86
Specifics of the influence of secondary support deformation characteristics on the gate roadways stability
Purpose. The research is aimed at determining the specifics of the influence of secondary support deformation characteristics on headgate stability in coal mines with steep-dipping seams. Methods. The deformation characteristics of secondary supports are determined in mine conditions based on instrumental observations of the displacement of reference points on the contour of headgate along the extraction site length. Secondary supports studied are in the form of coal pillars and timber packs. Findings. An assessment characteristic of the deformation properties of secondary supports is the ability to ensure the stability of side rocks and headgates in the mined-out space of the coal-rock mass. The determining factor in such an assessment is the load-bearing capacity of secondary supports. A distinctive peculiarity is a certain range of physical-mechanical characteristics and deformation processes, within which the resistance of supporting structures increases. At relative deformation ε ˂ 0.1-0.2, the resistance of coal pillars increases, which ensures the continuity of side rocks around the haulage drift and limits their displacement on the contour. After losing load-bearing capacity (ε ˃ 0.2), there is a periodic subsidence of the roof, which is accompanied by an increment in the displacement of side rocks on the headgate contour. In such conditions, the loss of cross-sectional area of the drifts exceeds 50%. For timber packs, after their compaction (ε = 0.4-0.5), resistance increases, effectively limiting the displacement of side rocks. The loss of cross-sectional area of the drifts does not exceed 30%. Originality. The dependence between the change in cross-sectional area (S) of the haulage drift and relative change in the volume of secondary supports per unit of convergence of side rocks ( ) has been determined. The presence of such dependence makes it possible to assess the state of headgates supported behind the stoping face at the extraction site. Practical implications. Coal pillars perform the functions of a supporting structure only within a certain range of deformation properties. Timber packs after their compaction allow limiting the displacement of side rocks on the headgate contour and ensuring its operational state.
- 1 December 2024
- Published by Donetsk National Technical University in SCIENTIFIC PAPERS OF DONNTU Series: “The Mining and Geology”
- No. 1(31)-2(32
ASSESSMENT OF THE BEARING CAPACITY OF PROTECTIVE STRUCTURES MADE OF ROCKING SHAPES FOR PREPARATORY MINING WORKS
Purpose.To evaluate the load-bearing capacity of protective structures made of crushed stone to ensure the stability of the preparatory production of the excavation site of the coal mine. Methods. Modeling of the deformation properties of protective structures made of crushed rock was performed on experimental samples during their static loading under the condition of uniaxial compression with the possibility of lateral expansion of the original material or its compression compression. Crushed rock of different granulometric composition was used as the starting material. Results. The conditions of compression of protective structures made of crushed rock determine their behavior and stress-strain state under static load. Taking into account the granulometric composition of the crushed rock, a difference of 1.8-2.6 times was established between the values of the relative deformation of the embedded material, which was in compression or uniaxial compression (with the possibility of lateral expansion of the crushed rock). The dual nature of the deformation effects, which affect the mechanical characteristics of embedded materials, is substantiated, which expands their ability to limit the movement of side rocks by providing the necessary bearing capacity, which affects the stability of the preparatory mine workings. Scientific novelty. The functional dependence between the compaction coefficients of the crushed rock and the transverse deformation of the embedded material was established, which makes it possible to evaluate the bearing capacity of protective structures under static load conditions in a stressed-deformed state. Practical significance. To assess the load-bearing capacity of protective structures of preparatory mining, it is necessary to take into account the granulometric composition of crushed rock, which affects the relative deformation and compaction coefficient of the embedded material. Keywords: guard building, bearing capacity, compaction coefficient, crushed rock, lateral breeds, preparatory production
- 1 December 2024
- Published by Donetsk National Technical University in SCIENTIFIC PAPERS OF DONNTU Series: “The Mining and Geology”
- No. 1(31)-2(32
ASSESSMENT OF THE BEARING CAPACITY OF PROTECTIVE STRUCTURES MADE OF ROCKING SHAPES FOR PREPARATORY MINING WORKS
Purpose.To evaluate the load-bearing capacity of protective structures made of crushed stone to ensure the stability of the preparatory production of the excavation site of the coal mine. Methods. Modeling of the deformation properties of protective structures made of crushed rock was performed on experimental samples during their static loading under the condition of uniaxial compression with the possibility of lateral expansion of the original material or its compression compression. Crushed rock of different granulometric composition was used as the starting material. Results. The conditions of compression of protective structures made of crushed rock determine their behavior and stress-strain state under static load. Taking into account the granulometric composition of the crushed rock, a difference of 1.8-2.6 times was established between the values of the relative deformation of the embedded material, which was in compression or uniaxial compression (with the possibility of lateral expansion of the crushed rock). The dual nature of the deformation effects, which affect the mechanical characteristics of embedded materials, is substantiated, which expands their ability to limit the movement of side rocks by providing the necessary bearing capacity, which affects the stability of the preparatory mine workings. Scientific novelty. The functional dependence between the compaction coefficients of the crushed rock and the transverse deformation of the embedded material was established, which makes it possible to evaluate the bearing capacity of protective structures under static load conditions in a stressed-deformed state. Practical significance. To assess the load-bearing capacity of protective structures of preparatory mining, it is necessary to take into account the granulometric composition of crushed rock, which affects the relative deformation and compaction coefficient of the embedded material. Keywords: guard building, bearing capacity, compaction coefficient, crushed rock, lateral breeds, preparatory production
- 30 June 2024
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 18 (2) , 122-131
Dualistic effect of the deformation of protective structures made of broken rock in mine workings under static load
Purpose is to reveal physical essence of the dualistic (double) nature of deformation effects and their influence on the mechanical properties of protective structures made of broken rock while unloading coal-bearing mass to ensure stability of side rocks and operational conditions of the development mine working within the working areas of coal mines. Methods. The deformation properties of protective structures made of broken rock was modeled on experimental samples during their static load in terms of uniaxial compression with the possibility of lateral expansion of the original material or its compressive stress. Findings. A dualistic effect of deformations for the conditions of uniaxial compression of protective structures was revealed. Under the effect, a complex transformation of volume and shape occurs in the structures caused by the process of relative changes in the backfill material volume. The observed phenomenon occurs within the range of 0.12 ≤δV ≤ 0.32 and the values of the compaction coefficient of broken rock being 1.13≤k con. ≤ 1.47, depending on the granulometric composition of the source material and its bulk density. It was established that under conditions when broken rock is compressed, there is an effect of forming the bearing capacity of protective structures, which is observed when a relative change in the volume of backfill material is 0.14 ≤ δV ≤ 0.38, and its compaction factor reaches 1.16 ≤ kcon. ≤ 1.59. Depending on the homogeneity degree of the backfill material of protective structures, when comparing the values of kcon., a dualistic (double) effect is manifested in the difference of deformation characteristics of broken rock under uniaxial and compressive stress, reaching two or more times. Originality. A regularity was established that determines the relationship between compaction factor kcon. of broken rock and a relative change in the volume (δV) of backfill material, which makes it possible to evaluate bearing capacity of protective structures, being under static load in a stress-strain state. Practical implications. The research results can be used to substantiate the selection of a method to protect development mine working with flexible supports made of broken rock. To clarify the assessment of bearing capacity of such structures, it is advisable to carry out specific field studies in mine conditions.
- 30 June 2024
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 18 (2) , 122-131
Dualistic effect of the deformation of protective structures made of broken rock in mine workings under static load
Purpose is to reveal physical essence of the dualistic (double) nature of deformation effects and their influence on the mechanical properties of protective structures made of broken rock while unloading coal-bearing mass to ensure stability of side rocks and operational conditions of the development mine working within the working areas of coal mines. Methods. The deformation properties of protective structures made of broken rock was modeled on experimental samples during their static load in terms of uniaxial compression with the possibility of lateral expansion of the original material or its compressive stress. Findings. A dualistic effect of deformations for the conditions of uniaxial compression of protective structures was revealed. Under the effect, a complex transformation of volume and shape occurs in the structures caused by the process of relative changes in the backfill material volume. The observed phenomenon occurs within the range of 0.12 ≤δV ≤ 0.32 and the values of the compaction coefficient of broken rock being 1.13≤k con. ≤ 1.47, depending on the granulometric composition of the source material and its bulk density. It was established that under conditions when broken rock is compressed, there is an effect of forming the bearing capacity of protective structures, which is observed when a relative change in the volume of backfill material is 0.14 ≤ δV ≤ 0.38, and its compaction factor reaches 1.16 ≤ kcon. ≤ 1.59. Depending on the homogeneity degree of the backfill material of protective structures, when comparing the values of kcon., a dualistic (double) effect is manifested in the difference of deformation characteristics of broken rock under uniaxial and compressive stress, reaching two or more times. Originality. A regularity was established that determines the relationship between compaction factor kcon. of broken rock and a relative change in the volume (δV) of backfill material, which makes it possible to evaluate bearing capacity of protective structures, being under static load in a stress-strain state. Practical implications. The research results can be used to substantiate the selection of a method to protect development mine working with flexible supports made of broken rock. To clarify the assessment of bearing capacity of such structures, it is advisable to carry out specific field studies in mine conditions.
- Open Access
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (1 (129)) , 57-68
Assessing the stability of protective structures in preparatory mining workings under conditions of static load
The object of this study is the deformation processes in protective structures under the action of static load in the coal massif in order to preserve the integrity of the side rocks and the operational condition of mine workings. Under laboratory conditions, the deformation characteristics of rigid and flexible protective structures, as well as supports made of crushed rock, were studied on experimental samples. The samples were subjected to uniaxial compression. It was established that there is a functional relationship between the coefficient of transverse deformation ν and the relative change in the volume δV of protection structures, which makes it possible to estimate their bearing capacity. For rigid protection structures (coal pillars, cast strip, cement blocks, blocks of reinforced concrete bollards, bundles of wooden racks), the deformed state of the structures determines their behavior. This happens at values of ν=0.3–0.5 and δV£0.09. Their stability is fixed within the safe deformation resource. An increase in the deformation energy density of such structures beyond the safe deformation resource leads to their destruction due to a change in shape. For flexible protection structures (bundles of wooden racks, rolling bundles made of wooden sleepers), which have a transverse deformation coefficient ν=0.02, at a relative change in volume δV£0.3, the compaction of structures is observed. Increasing their stiffness allows limiting the convergence of side rocks. For a support made of crushed rock, at ν=0.25–0.32 and a relative volume change of 0.12£δV£0.32, its compaction and increase in resistance occur. Under such conditions, the convergence of side rocks is limited. In order to preserve the integrity of the lateral and operational condition of preparatory workings in the excavation areas of coal mines, it is advisable to use flexible protective structures made of wood or supports made of crushed rock
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (1 (129)) , 57-68
Open AccessAssessing the stability of protective structures in preparatory mining workings under conditions of static load
The object of this study is the deformation processes in protective structures under the action of static load in the coal massif in order to preserve the integrity of the side rocks and the operational condition of mine workings. Under laboratory conditions, the deformation characteristics of rigid and flexible protective structures, as well as supports made of crushed rock, were studied on experimental samples. The samples were subjected to uniaxial compression. It was established that there is a functional relationship between the coefficient of transverse deformation ν and the relative change in the volume δV of protection structures, which makes it possible to estimate their bearing capacity. For rigid protection structures (coal pillars, cast strip, cement blocks, blocks of reinforced concrete bollards, bundles of wooden racks), the deformed state of the structures determines their behavior. This happens at values of ν=0.3–0.5 and δV£0.09. Their stability is fixed within the safe deformation resource. An increase in the deformation energy density of such structures beyond the safe deformation resource leads to their destruction due to a change in shape. For flexible protection structures (bundles of wooden racks, rolling bundles made of wooden sleepers), which have a transverse deformation coefficient ν=0.02, at a relative change in volume δV£0.3, the compaction of structures is observed. Increasing their stiffness allows limiting the convergence of side rocks. For a support made of crushed rock, at ν=0.25–0.32 and a relative volume change of 0.12£δV£0.32, its compaction and increase in resistance occur. Under such conditions, the convergence of side rocks is limited. In order to preserve the integrity of the lateral and operational condition of preparatory workings in the excavation areas of coal mines, it is advisable to use flexible protective structures made of wood or supports made of crushed rock
- 21 June 2024
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- Vol. 54 (1)
STUDY OF STABILITY OF ROLLING DEFORMATION OF STEEP LAYERS TAKING INTO ACCOUNT THE DAMAGE OF ARCH MOUNTING
Purpose. To investigate the stability of rolling back sections of steep layers by the method of protecting all coal, taking into account damage to the arch fastening along the length of the excavation section to assess the operational state of the preparatory production. Methods. To achieve the goal, mine instrumental observations of the stability of the rollback lines and the damage of the arch attachment in them along the length of the excavation were carried out. Results It is experimentally substantiated that increasing the density of the arch fastening installation in the preparatory work by 25% allows to reduce the convergence of side rocks along the contour by 5-7%. If the rollback area is protected by all the coal, at a distance of l50 m behind the cleaning well, a short-term stable state of production is ensured. At the same time, the frequency of damage to the flexible arch attachment is within 0.1 w 0.14. When the length of works increases to l>50 m, when the relative deformation of protective structures exceeds >0.25, their bearing capacity is lost and their destruction occurs. In such conditions, with the intensification of the convergence of the lateral rocks, the frequency of damage increases by 60-75%, which leads to a loss of 50% of the cross-sectional area of the rollback stretch and the impossibility of its further safe operation. Novelty. The functional dependence between the change in the relative deformation of the coal aggregates and the length of the preparatory workings l (m) was established, which has the form of a logarithmic function until the moment of the loss of the load-bearing capacity of the structures of the upper fence. , when the statistics of univariate analysis of variance of fastener failures have a standard normal distribution. Practical significance. The method of protecting preparatory workings with whole coal has a limited field of application due to the limited deformation resource of protective structures. In the zone of influence of cleaning works along the length of the mining area, the method of protecting the entire coal does not ensure maintenance of the workings without repair. Increasing the density of the fastening installation in the preparatory works will not significantly change the geomechanical situation in the coal massif.
- 21 June 2024
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- Vol. 54 (1)
STUDY OF STABILITY OF ROLLING DEFORMATION OF STEEP LAYERS TAKING INTO ACCOUNT THE DAMAGE OF ARCH MOUNTING
Purpose. To investigate the stability of rolling back sections of steep layers by the method of protecting all coal, taking into account damage to the arch fastening along the length of the excavation section to assess the operational state of the preparatory production. Methods. To achieve the goal, mine instrumental observations of the stability of the rollback lines and the damage of the arch attachment in them along the length of the excavation were carried out. Results It is experimentally substantiated that increasing the density of the arch fastening installation in the preparatory work by 25% allows to reduce the convergence of side rocks along the contour by 5-7%. If the rollback area is protected by all the coal, at a distance of l50 m behind the cleaning well, a short-term stable state of production is ensured. At the same time, the frequency of damage to the flexible arch attachment is within 0.1 w 0.14. When the length of works increases to l>50 m, when the relative deformation of protective structures exceeds >0.25, their bearing capacity is lost and their destruction occurs. In such conditions, with the intensification of the convergence of the lateral rocks, the frequency of damage increases by 60-75%, which leads to a loss of 50% of the cross-sectional area of the rollback stretch and the impossibility of its further safe operation. Novelty. The functional dependence between the change in the relative deformation of the coal aggregates and the length of the preparatory workings l (m) was established, which has the form of a logarithmic function until the moment of the loss of the load-bearing capacity of the structures of the upper fence. , when the statistics of univariate analysis of variance of fastener failures have a standard normal distribution. Practical significance. The method of protecting preparatory workings with whole coal has a limited field of application due to the limited deformation resource of protective structures. In the zone of influence of cleaning works along the length of the mining area, the method of protecting the entire coal does not ensure maintenance of the workings without repair. Increasing the density of the fastening installation in the preparatory works will not significantly change the geomechanical situation in the coal massif.
- 30 April 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 2,p. 32-37
Assessment of the state of the rock mass around the crosscuts under additional deformation disturbances
Purpose. Assessment of the level of disturbance of the stress state of the rock mass around the crosscut of the depth of 545 m when additional deformations occur during the mining of lower-lying coal pillars by southern longwalls of the k5 layer and assessment of this impact on operational production in the mining-geological and mining-technical conditions of Krasnolymanska mine. Methodology. Theoretical studies are based on the use of regulatory documents on the design of mining operations in coal mines and geomechanical models developed in accordance with the basic principles of solid mechanics, implemented in proven software products. Findings. As a result of the research, it has been proven that the mining-geological and mining-technical conditions of the stressed-strained state of the rock mass around capital workings at a depth of 545 are not critical for their stability. The ability to mine coal pillars at lower depths has been substantiated, and a minimum distance limit between research objects has been established, below which the fastening must be strengthened to ensure the stability of the crosscuts. Originality. For the first time, the stress-strain field in the rock mass around the basis workings has been studied as a result of the imbalance caused by previous mining during the excavation of underlying coal pillars under geological and technical conditions of Krasnolymanska mine based on geomechanical models. The regularity of the equivalent stress growth according to the Mohr-Coulomb criterion with a decrease in the distance between the research objects has been developed. Rational parameters of the technology for working out pillars are substantiated, under which the stress-strain state of the geomechanical system can be safely controlled. Practical value. The possibility of increasing the productive coal reserves within the field of the mine Krasnolymanska due to the safe mining of pillars around the basis inclines on the underlying levels is justified.
- 30 April 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 2,p. 32-37
Assessment of the state of the rock mass around the crosscuts under additional deformation disturbances
Purpose. Assessment of the level of disturbance of the stress state of the rock mass around the crosscut of the depth of 545 m when additional deformations occur during the mining of lower-lying coal pillars by southern longwalls of the k5 layer and assessment of this impact on operational production in the mining-geological and mining-technical conditions of Krasnolymanska mine. Methodology. Theoretical studies are based on the use of regulatory documents on the design of mining operations in coal mines and geomechanical models developed in accordance with the basic principles of solid mechanics, implemented in proven software products. Findings. As a result of the research, it has been proven that the mining-geological and mining-technical conditions of the stressed-strained state of the rock mass around capital workings at a depth of 545 are not critical for their stability. The ability to mine coal pillars at lower depths has been substantiated, and a minimum distance limit between research objects has been established, below which the fastening must be strengthened to ensure the stability of the crosscuts. Originality. For the first time, the stress-strain field in the rock mass around the basis workings has been studied as a result of the imbalance caused by previous mining during the excavation of underlying coal pillars under geological and technical conditions of Krasnolymanska mine based on geomechanical models. The regularity of the equivalent stress growth according to the Mohr-Coulomb criterion with a decrease in the distance between the research objects has been developed. Rational parameters of the technology for working out pillars are substantiated, under which the stress-strain state of the geomechanical system can be safely controlled. Practical value. The possibility of increasing the productive coal reserves within the field of the mine Krasnolymanska due to the safe mining of pillars around the basis inclines on the underlying levels is justified.
- 1 January 2024
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- No. 1(12)
STUDY OF THE DEFORMATION PROPERTIES OF PROTECTIVE STRUCTURES MADE OF MOUNTAIN SHAFT UNDER CONDITIONS OF STATIC LOAD
Purpose. Investigate the deformation properties of structures made of ground rock under static load conditions to preserve the integrity of the side rocks in the produced space of the coal massif and the operational state of the preparatory mine workings along the length of the excavation site. Methodology. In laboratory conditions, experimental samples of protective structures made of ground rock of heterogeneous granulometric composition were subjected to static loading under conditions of uniaxial and compression compression. Results. It was experimentally established that under the conditions of uniaxial compression of protective structures made of ground rock with the possibility of its lateral expansion, the effect of forming the bearing capacity is manifested in the relative change of the volume of the embedded material in the range of values , when, after increasing the relative deformation, the resistance reaches the maximum compaction of the rock . In such conditions, it is necessary to ensure the stability of the bearing pillar of the embedded material. During compressive compression of crushed rock, such an effect is achieved in conditions where the relative change in the volume of the embedded material is . After maximum compaction , the resistance of protective structures increases. Scientific novelty. The type of functional dependence between the relative deformation is established protective structures made of crushed rock and relative volume of the embedded material under static load under uniaxial and compressive compression, which allows to evaluate the bearing capacity of flexible supports. Practical significance. In order to assess the stability of protective structures made of crushed rock, which are in different compression conditions during the unloading of coal massif, it is necessary to take into account the compaction coefficient of the original material and the longitudinal deformation of the support under load. Keywords: coal massif, guard building, ground rock, uniaxial compression, compressive compression.
- 1 January 2024
- Published by Donetsk National Technical University in Naukovyi visnyk Donetskoho natsionalnoho tekhnichnoho universytetu
- No. 1(12)
STUDY OF THE DEFORMATION PROPERTIES OF PROTECTIVE STRUCTURES MADE OF MOUNTAIN SHAFT UNDER CONDITIONS OF STATIC LOAD
Purpose. Investigate the deformation properties of structures made of ground rock under static load conditions to preserve the integrity of the side rocks in the produced space of the coal massif and the operational state of the preparatory mine workings along the length of the excavation site. Methodology. In laboratory conditions, experimental samples of protective structures made of ground rock of heterogeneous granulometric composition were subjected to static loading under conditions of uniaxial and compression compression. Results. It was experimentally established that under the conditions of uniaxial compression of protective structures made of ground rock with the possibility of its lateral expansion, the effect of forming the bearing capacity is manifested in the relative change of the volume of the embedded material in the range of values , when, after increasing the relative deformation, the resistance reaches the maximum compaction of the rock . In such conditions, it is necessary to ensure the stability of the bearing pillar of the embedded material. During compressive compression of crushed rock, such an effect is achieved in conditions where the relative change in the volume of the embedded material is . After maximum compaction , the resistance of protective structures increases. Scientific novelty. The type of functional dependence between the relative deformation is established protective structures made of crushed rock and relative volume of the embedded material under static load under uniaxial and compressive compression, which allows to evaluate the bearing capacity of flexible supports. Practical significance. In order to assess the stability of protective structures made of crushed rock, which are in different compression conditions during the unloading of coal massif, it is necessary to take into account the compaction coefficient of the original material and the longitudinal deformation of the support under load. Keywords: coal massif, guard building, ground rock, uniaxial compression, compressive compression.
- 30 December 2023
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 17 (4) , 1-11
Deformation as a process to transform shape and volume of protective structures of the development mine workings during coal-rock mass off-loading
Purpose is to assess deformation characteristics of protective structures while coal-rock mass off-loading to ensure wall rock stability as well as operating conditions of the development mine workings in coal mines. Methods. In a laboratory environment, uniaxial compression of protective structures has been applied on the models to identify the influence by deformation processes on the changes in their rigidness resulting from the shape and volume transformation. Findings. Under the deformation of rigid structures in the context of a safe strain resource, potential energy of their changes in shape is 4.1-6.5 times higher than the one of changes in volume. Beyond the safe deformation resource when critical level of the specific potential strain energy has been exceeded, strength of protective structures is not sufficient to restrict wall rock movement limiting their use. If relative volume variation in the rigid protective structures is δV > 0.06-0.082 then they lose their stability. Under such conditions, structural rigidity decreases by 14-22%. If pliable wooden protective structures are used then relative 0.62 ≤ δV ≤ 0.72 volume change doubles their rigidity. In the circumstances, the potential shape change energy is 2.1 times higher than the volume change energy; the abovementioned favours temporary compaction of wooden components of the compressive structure while improving its resistivity. Originality. Regularities of changes in the specific potential deformation energy of protective structures depending upon their shape and volume variation in terms of uniaxial compression have been identified. Practical implications. To ensure stability of wall rocks and maintain operating conditions of the development mine wor-kings, it is reasonable to apply pliable wooden protective structures which will help restrict roof and floor movements after their compaction. Insufficient residual strength of rigid protective structures, resulting if they lose their stability, provokes rock failure within the working areas of coal mines.
- 30 December 2023
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 17 (4) , 1-11
Deformation as a process to transform shape and volume of protective structures of the development mine workings during coal-rock mass off-loading
Purpose is to assess deformation characteristics of protective structures while coal-rock mass off-loading to ensure wall rock stability as well as operating conditions of the development mine workings in coal mines. Methods. In a laboratory environment, uniaxial compression of protective structures has been applied on the models to identify the influence by deformation processes on the changes in their rigidness resulting from the shape and volume transformation. Findings. Under the deformation of rigid structures in the context of a safe strain resource, potential energy of their changes in shape is 4.1-6.5 times higher than the one of changes in volume. Beyond the safe deformation resource when critical level of the specific potential strain energy has been exceeded, strength of protective structures is not sufficient to restrict wall rock movement limiting their use. If relative volume variation in the rigid protective structures is δV > 0.06-0.082 then they lose their stability. Under such conditions, structural rigidity decreases by 14-22%. If pliable wooden protective structures are used then relative 0.62 ≤ δV ≤ 0.72 volume change doubles their rigidity. In the circumstances, the potential shape change energy is 2.1 times higher than the volume change energy; the abovementioned favours temporary compaction of wooden components of the compressive structure while improving its resistivity. Originality. Regularities of changes in the specific potential deformation energy of protective structures depending upon their shape and volume variation in terms of uniaxial compression have been identified. Practical implications. To ensure stability of wall rocks and maintain operating conditions of the development mine wor-kings, it is reasonable to apply pliable wooden protective structures which will help restrict roof and floor movements after their compaction. Insufficient residual strength of rigid protective structures, resulting if they lose their stability, provokes rock failure within the working areas of coal mines.
- 1 December 2023
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- Vol. 53 (2)
ASSESSMENT OF THE RISK OF LOSS OF STABILITY OF A SLOPE DRIFT IN THE DEVELOPMENT OF STEEP COAL SEAMS
Purpose. The purpose of the article is to assess the risk of loss of stability of the preparatory mine workings in order to adjust measures to prevent hazards and their consequences in the excavation areas of a coal mine with steep seams.. Method. An integrated approach was used, including: analysis and synthesis of known studies, expert evaluation, application of the basic principles of probability theory, processing, analysis and interpretation of the results. Results. During the examination of 7 objects (excavation sites), the a priori ranking identified significant factors that affect the loss of stability of preparatory mine workings. Accidental events were considered: the collapse of the roof, the slippage of the sole in the produced space of the coal massif, and the failure of fastening in the roll-back stretch. The ranking results are confirmed by the concordance coefficient (0,9). The analysis of accidents related to the loss of stability of the preparatory workings with different methods of protection allowed establishing the frequency of roof collapses and ground slides in the coal massif at the excavation site. To statistically evaluate the failures of the arch support ω in the working face, field studies were carried out. It was found that in the area of influence of the cleaning operations when protecting the heading with coal blocks, the failure rate of the arch support is ω=0.24, bushes from the racks ω=0,27, and wooden fires ω=0,16. Taking into account the combination of the identified significant factors, the a posteriori probability of loss of stability of the heading in the area of influence of the longwall face in the area of 10 ≤ l ≤ 45 m is 0,036-0,055 m when using coal blocks, 0,044-0,078 bushes from the risers and 0,0176-0,036 wooden fires. The probability of arch support failure is approximately 0,6. On the basis of research, a quantitative assessment of the component risks wa established, which leads to the loss of stability of the rollback stretch. The maximum risk assessment R = 576 corresponds to the conditions when the production is protected by bushes made of wooden risers. Scientific novelty Assessment of the risk of loss of stability of the preparatory mine workings is a set of research and analytical measures aimed at reducing the manifestation of hazards in the coal massif at the excavation sections of a coal mine. Practical significance. To obtain qualitative and quantitative estimates of the risk of loss of stability of the preparatory mine workings along the length of the excavation section, a model of formation of a possible dangerous situation was proposed. Key words: coal mine, preparatory workings, cave-in, side rocks, simulation modelling, miners’ safety.
- 1 December 2023
- Published by Donetsk National Technical University in JOURNAL of Donetsk mining institute
- Vol. 53 (2)
ASSESSMENT OF THE RISK OF LOSS OF STABILITY OF A SLOPE DRIFT IN THE DEVELOPMENT OF STEEP COAL SEAMS
Purpose. The purpose of the article is to assess the risk of loss of stability of the preparatory mine workings in order to adjust measures to prevent hazards and their consequences in the excavation areas of a coal mine with steep seams.. Method. An integrated approach was used, including: analysis and synthesis of known studies, expert evaluation, application of the basic principles of probability theory, processing, analysis and interpretation of the results. Results. During the examination of 7 objects (excavation sites), the a priori ranking identified significant factors that affect the loss of stability of preparatory mine workings. Accidental events were considered: the collapse of the roof, the slippage of the sole in the produced space of the coal massif, and the failure of fastening in the roll-back stretch. The ranking results are confirmed by the concordance coefficient (0,9). The analysis of accidents related to the loss of stability of the preparatory workings with different methods of protection allowed establishing the frequency of roof collapses and ground slides in the coal massif at the excavation site. To statistically evaluate the failures of the arch support ω in the working face, field studies were carried out. It was found that in the area of influence of the cleaning operations when protecting the heading with coal blocks, the failure rate of the arch support is ω=0.24, bushes from the racks ω=0,27, and wooden fires ω=0,16. Taking into account the combination of the identified significant factors, the a posteriori probability of loss of stability of the heading in the area of influence of the longwall face in the area of 10 ≤ l ≤ 45 m is 0,036-0,055 m when using coal blocks, 0,044-0,078 bushes from the risers and 0,0176-0,036 wooden fires. The probability of arch support failure is approximately 0,6. On the basis of research, a quantitative assessment of the component risks wa established, which leads to the loss of stability of the rollback stretch. The maximum risk assessment R = 576 corresponds to the conditions when the production is protected by bushes made of wooden risers. Scientific novelty Assessment of the risk of loss of stability of the preparatory mine workings is a set of research and analytical measures aimed at reducing the manifestation of hazards in the coal massif at the excavation sections of a coal mine. Practical significance. To obtain qualitative and quantitative estimates of the risk of loss of stability of the preparatory mine workings along the length of the excavation section, a model of formation of a possible dangerous situation was proposed. Key words: coal mine, preparatory workings, cave-in, side rocks, simulation modelling, miners’ safety.
- Open Access
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (1 (124)) , 85-95
Determining the deformation properties of crushed rock under compressive compression conditions
The object of this study is the process that forms fill materials from crushed rock under load for managing the condition of side rocks in a coal-bearing massif with preparatory workings. Deformation properties of crushed rock under laboratory conditions were evaluated on the basis of a study of compressive compression of the fill material. It was registered that there is a quadratic functional dependence between the change in the bulk density of crushed rock of different granulometric composition and the specific potential energy of deformation. It was experimentally established that the specific potential energy of deformation reaches the limit values at the maximum compression of crushed rock when the fill material consists of parts of different sizes. For experimental samples with different thickness of the rock layer h0 (m), there was a linear relationship between their longitudinal deformation Dh (m) and the external load F (kN), which determined the behavior of the deforming body at critical levels. Under such conditions, with a relative change in the volume of the fill material dV=0.36, that is, with the same relative deformation at any values of the parameter h0 (m) and the compaction coefficient of the crushed rock kcon=1.57, the maximum stiffness of the rock supports was ensured. With a limited amount of external static load on the experimental samples, in the process of their deformation when the parameter h0 was reduced by 2 times before their compression, the compaction coefficient of the crushed rock increased from kcon=1.33 to kcon=1.57. At the same time, the specific potential energy of deformation increased by 40 %, which made it possible to ensure the maximum rigidity of the fill material at the minimum value of the longitudinal deformation Dh (m) of the experimental samples
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (1 (124)) , 85-95
Open AccessDetermining the deformation properties of crushed rock under compressive compression conditions
The object of this study is the process that forms fill materials from crushed rock under load for managing the condition of side rocks in a coal-bearing massif with preparatory workings. Deformation properties of crushed rock under laboratory conditions were evaluated on the basis of a study of compressive compression of the fill material. It was registered that there is a quadratic functional dependence between the change in the bulk density of crushed rock of different granulometric composition and the specific potential energy of deformation. It was experimentally established that the specific potential energy of deformation reaches the limit values at the maximum compression of crushed rock when the fill material consists of parts of different sizes. For experimental samples with different thickness of the rock layer h0 (m), there was a linear relationship between their longitudinal deformation Dh (m) and the external load F (kN), which determined the behavior of the deforming body at critical levels. Under such conditions, with a relative change in the volume of the fill material dV=0.36, that is, with the same relative deformation at any values of the parameter h0 (m) and the compaction coefficient of the crushed rock kcon=1.57, the maximum stiffness of the rock supports was ensured. With a limited amount of external static load on the experimental samples, in the process of their deformation when the parameter h0 was reduced by 2 times before their compression, the compaction coefficient of the crushed rock increased from kcon=1.33 to kcon=1.57. At the same time, the specific potential energy of deformation increased by 40 %, which made it possible to ensure the maximum rigidity of the fill material at the minimum value of the longitudinal deformation Dh (m) of the experimental samples