VNVolodymyr Novodvorskyi

Volodymyr Novodvorskyi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Volodymyr Novodvorskyi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:

  • Georgiy Ivanitsky

    Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute

    2 shared publications
  • N. P Shved

    Національний технічний університет України «Київський політехнічний інститут імені Ігоря Сікорського

    1 shared publication
  • Nikolai Shved

    1 shared publication
  • Микола Петрович Швед

    Національного технічного університету України «Київський політехнічний інститут імені Ігоря Сікорського

    1 shared publication

Latest Publications

  • CONTROL OF THE SHEAR STRAIN IN THE HOMOGENIZATION ZONE OF THE DISK EXTRUDER

    by Volodymyr Novodvorskyi, Nikolai Shved

    Простий метод визначення якості розплаву полімеру є дуже важливим у виробництві. Метод який забезпечує простоту і швидке використання, що робить його цінним для оптимізації процесів екструзії. В роботі описано те, як можна покращити змішуючий ефект змінюючи швидкісні поля і тим самим змінюючи значення деформації зсуву. Для усіх чотирьох каналів зони гомогенізації дискового екструдера проведено розрахунок деформації зсуву. Встановлено, що зміна частоти обертання диска дозволяє змінювати деформацію зсуву від 3324 до 4966 при незмінній продуктивності для усієї зони гомогенізації. Було оцінено вплив різних каналів на ефект перемішування: перший, другий, третій і четвертий канали вносять 21%, 57%, 15% і 7% відповідно до загальної ефективності перемішування в зоні гомогенізації. Крім того, було виявлено, що другий канал зазнає найвищих значень деформації зсуву. У випадку третього каналу, хоча значення швидкості зсуву відносно високі, короткий час перебування розплавленого елемента призводить до порівняно менших значень деформації зсуву. Середні значення деформації зсуву залишаються постійними для заданої швидкості обертання диска. Описане вказує на можливість оцінювання якості змішування по кількості підведеної енергії, що спрощує процес визначення якості розплаву, а також його регулювання.

  • Open Access

    Modeling of Non-Isothermal Polymer Melt Flow in a Conical Annular Channel of a Disk Extruder

    by V. V. Novodvorskyi, G. K. Ivanitskyi, N. P. Shved

    Purpose. The homogenization zone consists of various channels with different configurations, for each of which it is necessary to determine the passage of the melt flow process, and on its basis - the velocity fields, which determine the quality of mixing and distribution of components in the melt. To ensure a flexible and controllable homogenization process with the possibility of improving the quality of the melt, it is necessary to study the flow processes in the channels of a disk extruder. Therefore, the main objective of this work is to perform hydrodynamic modeling of processes during melt flow in a conical channel. Methodology. To achieve this goal, we propose a methodology for determining the flow processes in a conical channel, and find out which zones are convenient to consider in a special conical orthogonal coordinate system. For this purpose, the change in the radial coordinate , which has the same meaning in both the straight and the conical gap, was described - it is a coordinate along the width of the gap. This makes it possible to further apply this coordinate for the width of the disk gap - between the moving and stationary disks. Findings. A method has been proposed that describes the flow processes in the conical channel of the homogenization zone of a disk extruder. The calculation procedure is presented in an analytical form, and graphical dependences of the distribution of tangential and longitudinal velocities and shear velocities of the melt flow along the width of the annular channel at the nominal and maximum disk speeds and at the nominal and maximum disk gap are also given. Originality. For the first time, a methodology for calculating the conical channel of the homogenization zone of a disk extruder is presented, which describes the flow processes in a conical orthogonal coordinate system, which allows taking into account the common coordinate for the entire homogenization zone. The general procedure for calculating the channels of the homogenization zone has been supplemented. Practical value. The procedure for calculating the channels of the homogenization zone, which was started earlier, was extended and applied to the flow in a conical annular channel. This coordinate allows us to describe the flow processes along the width of the channel for all channels of the homogenization zone of a disk extruder, which greatly simplifies the calculations. Important results of hydrodynamic and thermal processes were obtained for the annular channel, which makes it possible to design disk extruders with greater accuracy and calculate their optimal operating modes.

  • Open Access

    Modeling Of Polymer Melt Flow In The Annular Channel Of A Disk Extruder

    by V. V. Novodvorskyi, G. K. Ivanitsky

    Purpose. Polymer products are used in industry due to their performance properties. The homogeneity of the melt is essential for the quality of the final product. Uniform distribution of components and properties ensures homogeneity of the product's physical and mechanical characteristics. Insufficient homogeneity can lead to defects in the product. The homogenization zone plays an important role in ensuring a homogeneous melt. In a disc extruder, the homogenization zone consists of four consecutive channels. In order to describe the flow for the entire homogenization zone, it is necessary to model the first channel first. Therefore, the main purpose of this work is to model hydrodynamic and thermal processes during the flow of a non-Newtonian fluid in a straight annular channel in a non-isothermal regime, as well as to create a general procedure for further calculations for other channels. Methodology. The analysis of publications was carried out. The procedure for calculating the velocity and shear rate of the longitudinal and tangential melt flow, the effective melt viscosity, and the calculation of the melt temperature change along the length of the annular gap in an analytical form was developed. Findings. In accordance with the developed procedure, the values of tangential and longitudinal velocities and shear rates were calculated. The graphical dependences of the distribution of tangential and longitudinal velocities and shear velocities of the melt flow along the width of the annular channel, the distribution of pressure and the temperature of the polymer melt averaged over the width of the gap along the length of the annular channel are presented. Originality. In this work, a stationary flow in a straight annular channel was modeled for LDPE of the 15803-020 grade in a non-isothermal regime. A general procedure for further calculations for other channels of the homogenization zone has been developed. Practical value. The given calculation procedure can be applied to the following channels of the homogenization zone, which allows describing the melt flow for the entire homogenization zone.


  • Open Access

    The Process of Melt Homogenization in a Metered-Discharge Disk Extruder

    by V. V Novodvorskyi, N. P Shved

    Purpose. This paper aims to develop a physical model of the homogenization process in a metered-discharge disk extruder, as well as to select and justify the variable parameters that can be used to evaluate the efficiency of mixing and process control. Methodology. With the advent of a large number of alloying additives, filled and composite materials, there is a need for continuous monitoring and control of the melt homogenization process. In classical worm extruders, the processes of feeding, melting, homogenization, and pressure generation are interconnected and are triggered simultaneously by a single working body, the worm, which makes it impossible to control each process separately to optimize them. In such cases, cascade extrusion schemes are used, where the process is divided into separate subprocesses or groups of them with the ability to control them independently. Findings. The scheme of a cascade disk-gear extruder is described, where a metered-powered disk extruder is used as a melt-homogenizer, and a gear pump is used to create pressure and dosing. The variable parameters of the disk extruder for adjusting the mixing efficiency are selected and substantiated. The speed components and their ratios for different parts of the homogenization zone are analyzed. The expediency of using a disk extruder as a melt-homogenizer in cascade extrusion schemes is substantiated. The adequacy of using the mixing index in the form of temperature inhomogeneity is emphasized. The homogenization zone in the form of four separate subzones and changes in the accumulated shear strain along each subzone, as well as the possibility of their regulation, are described. Originality. For the first time, a hydrodynamic model of processes in the homogenization zone of a metered-discharge disk extruder was developed and described. Practical value. The possibility of adjusting the velocity field in the homogenization zone of a disk extruder has been substantiated, which allows controlling the mixing effect directly during the extrusion process. The possibility of selecting the optimal mode of operation of the homogenization zone makes it possible to obtain a melt of a given quality with minimal energy consumption.