Rakesh Varma Rena
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rakesh Varma Rena has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Raviteja Kammari
School of Electrical and Computer Sciences, Indian Institute of Technology Bhubaneswar, Bhubaneswar, India
2 shared publications Vijay Shankar P.
School of Electrical Sciences, Indian Institute of Technology Bhubaneswar, Bhubaneswar, Odisha, India
1 shared publication- Vijaya Sankara Rao Pasupureddi
Indian Institute of Technology Bhubaneswar
1 shared publication
Latest Publications
- 19 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 32 (3) , 552-563
A 0.4–1.8-GHz Quarter-Rate Subsampling Mixer-First Direct Down-Conversion RF Front-End
Subsampling down-conversion has not been a popular choice for mixer-first RF front-ends for two interdependent reasons. One, the subsampling down-conversion is inherently heterodyne in nature. Two, as a consequence to one, the passive mixer transparency property can not be exploited for providing impedance matching at the RF port by impedance translation. In this work, an eight-path quarter-rate subsampling (QRSS) mixer-first direct down-conversion architecture is proposed to address these issues. The proposed architecture simultaneously achieves quadrature direct down-conversion and impedance matching by using the third harmonic of the QRSS frequency, $f_{s}$ . The impedance matching is achieved by exploiting the eight-path passive mixer transparency property. Compared to RF sampling receivers, this architecture employs a sampling frequency $f_{s}$ three times lesser than $f_{\text {RF}}$ , saving on the power consumption of nonoverlapping clock generation, distribution circuits, and frequency synthesizer. A test chip is fabricated in 1.2-V, 65-nm CMOS with an active area of 0.32 mm2. The subsampling eight-path mixer, baseband low-noise amplifier (LNA), and ${\text{g}_{m}}$ -cell consume a power of $800 \mu \text{W}$ , 23 mW, and 3 mW, respectively, for a target bandwidth of 90 MHz. Nonoverlapping clock generation circuit consumes 2–9.2 mW, over the band 0.4–1.8 GHz. The receiver has a double sideband (DSB) noise figure of 4.7 dB, a conversion gain of 22 dB, an in-band (IB)-IIP3 of −1 dBm, and OB-IIP3 of +8 dBm.
- 19 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 32 (3) , 552-563
A 0.4–1.8-GHz Quarter-Rate Subsampling Mixer-First Direct Down-Conversion RF Front-End
Subsampling down-conversion has not been a popular choice for mixer-first RF front-ends for two interdependent reasons. One, the subsampling down-conversion is inherently heterodyne in nature. Two, as a consequence to one, the passive mixer transparency property can not be exploited for providing impedance matching at the RF port by impedance translation. In this work, an eight-path quarter-rate subsampling (QRSS) mixer-first direct down-conversion architecture is proposed to address these issues. The proposed architecture simultaneously achieves quadrature direct down-conversion and impedance matching by using the third harmonic of the QRSS frequency, $f_{s}$ . The impedance matching is achieved by exploiting the eight-path passive mixer transparency property. Compared to RF sampling receivers, this architecture employs a sampling frequency $f_{s}$ three times lesser than $f_{\text {RF}}$ , saving on the power consumption of nonoverlapping clock generation, distribution circuits, and frequency synthesizer. A test chip is fabricated in 1.2-V, 65-nm CMOS with an active area of 0.32 mm2. The subsampling eight-path mixer, baseband low-noise amplifier (LNA), and ${\text{g}_{m}}$ -cell consume a power of $800 \mu \text{W}$ , 23 mW, and 3 mW, respectively, for a target bandwidth of 90 MHz. Nonoverlapping clock generation circuit consumes 2–9.2 mW, over the band 0.4–1.8 GHz. The receiver has a double sideband (DSB) noise figure of 4.7 dB, a conversion gain of 22 dB, an in-band (IB)-IIP3 of −1 dBm, and OB-IIP3 of +8 dBm.
- 5 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 31 (7) , 1065-1077
0.4-1 GHz Subsampling Mixer-First RF Front-End With 50-dB HRR, +10-dBm IB-IIP3 in 65-nm CMOS
Reconfigurable subsampling mixer-first RF front-end is a potential candidate for low-power applications as it operates at a low clock frequency and hence consumes low power. However, the subsampling down-conversion has not been employed in mixer-first RF front-ends due to the disadvantage of high noise figure from inherent noise folding and lack of RF port impedance matching because of nonzero IF down-conversion. To address the above two issues, first, a subsampling multipath down-conversion mixer scheme is proposed for rejecting $3f_s/4$ and $5f_s/4$ down-conversions, thereby alleviating the effect of noise folding, leading to low noise figure. Second, an IF-stage impedance matching scheme is proposed that provides 50 $\Omega$ matching at the RF port of the mixer using an IF-LNA in shunt with an $M$ -phase switch-capacitor filter. The analysis of the proposed scheme in terms of noise figure, conversion gain, and harmonic rejection is presented. The proposed subsampling mixer-first RF front-end is implemented in 1.2 V, 65-nm CMOS technology. The prototype occupies an active area of 0.33 mm $^2$ , the switch-capacitor mixer and $M$ -phase filter consume 400 $\mu$ W of power, and IF amplifier and nonoverlapping clock generation circuit consume 25 mW and 6–12.6 mW of power, respectively. The RF front-end achieves a 6.5-dB noise figure, 15.1-dB conversion gain, 50-dB harmonic rejection ratio (HRR), and $+$ 10-dBm IB-IIP $_3$ .
- 5 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 31 (7) , 1065-1077
0.4-1 GHz Subsampling Mixer-First RF Front-End With 50-dB HRR, +10-dBm IB-IIP3 in 65-nm CMOS
Reconfigurable subsampling mixer-first RF front-end is a potential candidate for low-power applications as it operates at a low clock frequency and hence consumes low power. However, the subsampling down-conversion has not been employed in mixer-first RF front-ends due to the disadvantage of high noise figure from inherent noise folding and lack of RF port impedance matching because of nonzero IF down-conversion. To address the above two issues, first, a subsampling multipath down-conversion mixer scheme is proposed for rejecting $3f_s/4$ and $5f_s/4$ down-conversions, thereby alleviating the effect of noise folding, leading to low noise figure. Second, an IF-stage impedance matching scheme is proposed that provides 50 $\Omega$ matching at the RF port of the mixer using an IF-LNA in shunt with an $M$ -phase switch-capacitor filter. The analysis of the proposed scheme in terms of noise figure, conversion gain, and harmonic rejection is presented. The proposed subsampling mixer-first RF front-end is implemented in 1.2 V, 65-nm CMOS technology. The prototype occupies an active area of 0.33 mm $^2$ , the switch-capacitor mixer and $M$ -phase filter consume 400 $\mu$ W of power, and IF amplifier and nonoverlapping clock generation circuit consume 25 mW and 6–12.6 mW of power, respectively. The RF front-end achieves a 6.5-dB noise figure, 15.1-dB conversion gain, 50-dB harmonic rejection ratio (HRR), and $+$ 10-dBm IB-IIP $_3$ .